Benutzeranleitung / Produktwartung VoIP Analog Telephone Adapter VIP-157S des Produzenten Planet
Zur Seite of 71
VoIP Analog Telephone Adapter VIP-156/VIP156PE/VIP-157/VIP-157S User’s manual Version 3.1 1.
Copyright Copyright (C) 200 8 PLANET T echnology Corp. All rights reserved. The products and programs described in this User ’s Manu al are licensed products of PLANET T echnology , This User ’s M.
3 Revision User ’s Manual for PLANET V oIP Analog T elephone Adapter: Model: A T A Rev: 3.1 (2008, February) Part No. EM-VIP_A T A V3.1.
4 T ABLE OF CONTENTS Chapter 1 ................................................................................................................................... 6 Introductio n ........................................................................
5 Codec ID Setting ............................................................................................................................... .3 7 DTMF Setting ......................................................................................
6 Chapter 1 1 Introduction Overview Based on years of VoIP manufacturing experien ces , PLANET Technology VoIP total solutio ns are known for advanced implementation of standards bas ed telephony with mass deployment capability.
• Voice processing: Voice Active Detection, DT MF detection/ generat ion, G.168 echo cancellation (16mSec.), Comfort noise gene ration (CNG) • In band, out-of-band, and SIP-info DTMF support Packa.
Left / Right Panel of VIP-156 Front Panel of VIP-156PE Left / Right Panel of VIP-156PE 8.
Front Panel of VIP-157 Left / Right Panel of VIP-157 Front Panel of VIP-157S 9.
Left / Right Panel of VIP-157S LED Display & Button 1 PC RJ-45 connector, to maintain t he existi ng network structure, connected directly to the PC through straight CAT-5 cable 2 LAN RJ-45 connector, for Internet a ccess, connected directly to Sw it ch /H ub through straight CAT-5 cable.
LED display of VIP-156 / VIP-156PE LED Indicators Descriptions PWR Power is supplied to the device. ST A TUS The S t atus LED will be flashing when the machine i s operational LNK/ACT OFF : the device is connected to LAN at 10Mb/s. ON : the device is connected to LAN at 100Mb/s.
2 Chapter 2 Preparations & Installation Physical Inst allation Requirement This chapter illustrates ba sic installation of ATA analog Phone Adapter ((“ ATA ” in the following term)) • Network cables. Use standard 10/1 00Ba seT network (UTP) cables with RJ45 connectors.
LAN IP address configuration vi a web configuration interface Execute your web browser, and insert the IP addre ss ( default: 192.168.0.1 ) of V IP in the adddress bar.
14 Client #1 12xxx *xxx*xxx* xxx# Setup S tatic IP Address Use the * (star) key when entering a decimal point. DHCP will be disabled and system will change to the S tatic IP type. #1 13xxx *xxx*xxx* xxx# Set Network Mask Use the * (star) key when entering a decimal point.
15 address of the A T A. #125# Check Primary DNS Server Setting IVR will announce the current setting in the Primary DNS field. #126# Check LAN IP Address IVR will announce the current LAN port IP address of the A T A. #128# Check Firmware V ersion IVR will announce the version of the firmware running on the A T A.
Port Port #147+Number# enable forward to FXO Port Eanble forward to FXO Port #116# Enable PPTP function None Enable PPTP function #117# Disable PPTP function None Disable PPTP function #118# Enable VL.
17 Chapter 3 Network Service Configurations 3 Configuring and monitoring yo ur A T A from web browser The A T A integrates a web-based graphi cal user in terface that can cover most configurations and machine st atus monitoring. V ia standard web browse r , you can configure and ch e from anywhere around the world.
V oIP Phone Adatper main page 18.
Chapter 4 VoIP Telephone Adapter Configurations Phone Book A T A can set up 140 records of Phone Book. Use r can dial the Name records to make call s via Phone Book feature. 19 Field Description Phone Book Page The default is Page 1. It can sele ct Page 1 ~ Page 14 to look round Phone Book record s.
If you need to add a phone number into the Phone Book list, you need to input the positio n, the name, and the phone number (by URL type). When you finished a new phone list, just click the “Add Phone” button. If you want to delete a phone number , you can sele ct the phone number you want to delete then click “Delete Selected” button.
speed dial number you cho ose. Busy Forward : If you are on the phone, the ne w incoming ca ll will forward to the number you choo sed. Y ou can input the name and the phone number in URL field. No Answ er Forw ard : If yo u can not answer the phone, the incoming call will forward to the number you chosen.
Call Forward function for VIP-157 SNTP settings This page defines the p rim ary and seco nd SNTP Server IP Address, to get the date/time information. Also you can base on your location to set the T ime Zone, and how long need to synchronize a gain. When you finished the setting, please cli ck the Su bmit button.
V olume Settings for VIP-154T/VIP-154PT Beside the above settings, VIP-157 also can set the volume of PSTN. PSTN-Out V olume is to set the PSTN volume for you can hear .
Auto Answer (For VIP-157) This page defines the Auto Answer function. Y ou can set the Auto Answer function to answer t he incoming call by the phone. If the call is come from the IP , then the VIP-157 can let user to redial the call to PSTN phone number .
Dial Plan Settings This page defines the Dial Plan Setting function. Th is function is wh en you input the pho ne number by the keypad but you don’t need to pre s s “#”. After time out the system will dial directly . Field Description Drop Prefix The rule of add or replace code.
26 the max length is 40. - Symbol: It onl y accept the [+], [x] - +: It means as “or”. For ex am ple, [123+456+334+5xx] even if [123 or 456 or 334 or 5xx] - x: It is equal to 0~9.
Example_4: Dial Now: *xx+#xx+1 1x+xxxxxx 1. If the dialing number is match with the rule of “ *xx ” , it will send out the dialing number directly . For example, *00/ *01/ *02 … *99 . 2. If the dialing number is match with the rule of “ #xx ” , i t will send out the dialing number directl y .
waiting notice in your current call. If you set t he function to Of f, then you will not hear any notice. T.38 (FAX) Settings This page defines the T .38 (F AX) Setting function. Y ou can Enable/Disable the T .38 function, and can modify the T .38 transmission port of each FXS port.
the specific number automatically . Use Hot Line: Click Enable to carry the Hot line function out. Hot line number: Th e hot line number , it can input the IP address or registration number . Alarm Settings This page defines the Alarm setting in this page.
- Fixed IP: It could setup the IP address manual. - DHCP Client: It will acqui re the IP address automatically . - PPPoE: It will use the PPPoE connection method. IP: The IP address Mask: The sub net address Gateway: The default gateway address DNS Server1: The defa ult is 168.
DHCP Serv er: It will allot the IP address automati cally when enabke this function. Star t IP : S tart IP of lease table End IP: End IP of lease t able.
VLAN Settings This page defines the VLA N setting in this page. This function n eed s to co-operate with network devices which have VLAN function. VLAN Packet s: If setup a s On, it could receive VLA N messages. VID (802.1Q/T AG): Dispose VLAN ID is add a T ag header aft er rea lize enable the VLAN function.
DMZ Settings This page defines the DMZ setting in this page. DMZ: If setup as On, all of pa cket s (expect SIP pa ckets) will sen d to the spe cific IP address. DMZ Host IP: The DMZ host IP address. Virtual Server This page def ines the Virtual Server setti ng in this page.
External Port: For corresponding the external port. Server IP: T o input the Server IP address. PPTP Settings This page defines the PPT P setting in this page. Y ou could setup the PPTP Server conne ctio n information. When you finished the se tting, please click the Su bmit button.
Service Domain Settings In Service Domain Function you need to input the a ccount and the related informations in thi s p age, please refer to your ISP provider . Y ou can register three SIP account in the A T A. Y ou can dial the V oIP phone to your friends via first enable SIP account and receive the phone from these three SIP accounts.
For example: The default is realm 1, inpu t the 2* (Follow by the # key) from keypa d and hang up the telephone set. It will switch to realm 2, and it can make the SIP calls via realm 2. Port Settings This page defines the SIP and RTP port number in th is p a ge.
Codec ID Setting This page defines the Cod ec ID. Sometimes 2 V oIP devices with dif ferent Codec ID will cause the interopability issue. If you are t al k ing with others got some problems , you may ask the other one what kind of Codec ID he use, then you can change your Codec ID.
DTMF Setting This page def ines the RFC2833 Out-Band DTMF , Inband DTMF and Send DTMF SIP Info in this p age. T o change this setting, please following your ISP information. When you finished the setting, please click the Submit button. RPort Settings This page defines the RPort Enable/Disa ble in this page.
Other Settings This page defines the Hold by RFC, V oice/SIP Qo S and other settings in this page. T o change these settings please following your ISP information. When you finished the setting, please click the Submit button. Hold by RFC: The default is disa ble, and to st art up communication hold back function (RFC definition).
Auto Configuration This page defines the Auto Configuration (Auto Pr ovision) setting. A T A support s TFTP , FTP , HTTP and IP PBX auto config uration function in tot al. In IP PBX Auto Configuration Setting you need to check wit h your service provider if they have provid ed this function.
PTT Settings for VIP-156/VIP-157S Beside the above settings, VIP-157 also can set co unt ry of FXO port. PTT Settings for VIP-157 Cancel without to tag This function can decide th e device if send the canc el tag to Proxy Server .
MAC address for PPPoE dial-up connection. Please refer to the following operate pro cedures fo r more underst andings to carry out the MAC Clone function. 1. Please login A T A and browse to “ Ne twork -> LAN Settings ” p age. T o switch the LAN mode to NA T mode then press Save&Reboot button to save the settings an d reboot machine.
5. After Save&Reboot , the MAC of LAN port will become to PC’ s original MAC address. Tone Settings This page defines the T one settings. This function ca n setup the re lated parameters of Dial T one, Ring Back T one, Busy T one, Error T one and Inser T one.
(The Registration Server al so ne ed support this function) CPC Delay : When receive the disconnect signal, machine will to cut the voltage down to 0V af ter this time. CPC Duration: When st arting to cut the volt age down to 0V , machine will to continue this stat e by this time.
Save & Reboot In Save & Reboot you can save the changes you have done. If you want to use new setting in the Phone Adapter , Y ou have to click the Save button. Af ter you cli ck the Save button, the Phone Adapter will automatically restart and the new setting will effect .
Auto Upgrade The device can update new firmware with the gz or ds file format automatically by the Auto Upgrade function. Field Descriptions Up date via There are TFTP/ FTP and HTTP three ways to provide the auto upgrade function. TFTP Serv er Input the TFTP Server add ress, and it co uld input the IP or Domain Name form.
firmware. - Power On (+ Scheduling) : The m achine will check the new firmware when power on and followi ng the sche duling date and time. - Scheduling : The machine will follow the scheduling date and time to check the new firmware. Scheduling (Date) The machine will check the new fi rmware between the time range by random.
48.
Appendix A V oice Communication Samples There are several ways to make call s to desired dest ination in A T A. In this section, we’ll lead you step by step to establish your first voice com muni cation via keyp ad and web browsers operations.
Case 2: (Peer-to-Peer mode) VIP-157S Port 1 to Port 2 communications Supposing one VIP-157S connect s to two telephones, just pick up phone 1 and di al ‘ 192*168*0*1**5062 ’, phon e 2 will ring. Analog telephone sets a re connected to the phon e (RJ-1 1) ports of VIP-157S respectively 192.
Case 3: Voice communication vi a SIP proxy server – SIP-50 Registration / Registration / 51 ATA A IP Address: 192.168.0.1 Line Number: 1001 SIP-50 IP Address: 192.
52 STEP 3: Repeat the same configuration ste ps on A T A B , and che ck the machine registration st atus, make sure the regi stratio ns are completed. T est the scenario: 1. Pick up the telephone on A T A A 2. Press the keypad: 2002 shall be able to connect to the A T A B 3.
Case 4: Voice communication via IP PBX system – IPX-2000 (Auto-config) In the following sample, we’ll introduce how to in tegrate the A T A with our IP PBX system IPX-2000 via Auto-config feature. Registration / Authentication Registration / Authentication IPX-2000 LAN IP Address: 192.
STEP 2: Please browse to the Device Æ IP Phone menu and create new dev ice. And press the EDIT button for set up the Auto Config configuration. STEP 3: Please fill out the V endor Prefix code and MAC Address of A T A. L Note : The following are the V endor Prefix of devices: 1.
STEP 5: After setting up the p arameters, please browse to the Service Æ IP PBX serv ice menu, and press RELOAD of IP PBX configuration reload select ion for activating the settings. Device configurations on the A T A: STEP 6: Please log in A T A via web browser , bro wse to the SIP setting menu and select the Domain Service config menu.
STEP 7: After enablin g the auto-co nfig feature, the A T A shall be able to obt ain IP address and SIP extension information from IP PBX system IPX- 2000 information. T o verify the auto-config results, you may conn ect telephone set to A T A; press #120# to check if the IP addre ss is obtained from IPX-2000.
Case 5: Call Forward Feature_Example 1 In the following samples, we’ll introduce the Call Forward Feat ure applications. In this example, there are three VIP-156 register to IPX-300 and VIP-156_A had set Call Forward function to VIP-156_B.
58 T est the scenario: 1. VIP-156_C pick up the tele phon e 2. Dial the number 1001(VIP-156_A), 3. Because VIP-156_A h ad se t up All Forward function to the number 2002(VIP-156_B) 4.
Case 6: Call Forward Feature_Example 2 In this example, there are one VIP-157 and two VIP-156 register to IPX-300. The VIP-157_A had set Call Forward function to phone num be r 1 1 1 1-2222 (PSTN).
T est the scenario: 1. VIP-156_C pick up the tele phon e 2. Dial the number 1001(VIP-157 _A) 3. Because VIP-157_A h ad se t up All Forward function to the PSTN Phone Number 1 1 1 12222 4.
Case 7: Call Forward Feature_Example 3 In this example, there are one VIP-157 and two VIP-156 register to IPX-300. The VIP-157_A had set Call Forward function to number 2002 (V IP-156_B). Machine configurat ion on the VIP-157: Please log in VIP-157_A via web browser , browse to the Phone Settings menu and select the Call Forward config menu.
T est the scenario: 1. PSTN Phone Number 1 1 1 12222 pick up the telepho ne 2. Dial the PSTN Phone Number 333344 44(VIP-157_A) 3. Because VIP-157_A h ad se t up All Forward function to the number 2002(VIP-156_B) 4.
Case 8: Call Forward Feature_Example 4 In this example, there are three VIP-156 and conne ct with Peer to Peer mode. VIP-156_A had set Call Forward function to VIP-156_B. Machine configurat ion on the VIP-156: Please log in VIP-156_A via web browser , browse to the Phone Settings menu and select the Call Forward config menu.
Case 9: Auto Answer Feature_IP to PSTN In this example, there are one VIP-157 and two VIP- 156 and conn ect with Pee r to Peer mode. The VIP-157_A had set Auto Answer function for forw ardi ng calls to arbitrary telephone.
the Auto Ans wer config menu. In the setting page, pl ease ena ble the Aut o Answ er and PIN Code Enabled function, then the sample configur ation screen is shown below: T est the scenario: 1. VIP-156_C pick up the tele phon e 2. Dial the IP Addre ss 192.
Case 10: Auto Answer Feature_PSTN to IP In this example, there are one VIP-157 and two VIP- 156 and conn ect with Pee r to Peer mode. The VIP-157_A had set Auto Answer function for forwardi ng to arbitrary telephone.
T est the scenario: 1. The Phone Number 1 1 1 12222 pick up the telephone 2. Dial the PSTN Phone Number 333344 44(VIP-157_A) 3. VIP-157_A wi ll ring up but doesn’t answer the call 4. After 3 rings, the Phone Number 1 1 1 12222 will hear the prompt sounds then input the pass wor d 123# 5.
68 Appendix B The method of operation guide In this section, we’ll introduce the feature s method of operation, and lead you ste p by step to establish these features. Call Transfer A. Blind T ransf er 1. B call to A and they are in the process of conversation.
69 the switch code. Realm switch code: 1* : Realm 1 2* : Realm 2 3* : Realm 3 For example: The default is realm 1, inpu t the 2* (Follow by the # key) from keypa d and hang up the telephone set. It will switch to realm 2, and it can make the SIP calls via realm 2.
70 Appendix C VIP-156/VIP-156PE/VIP-157/VIP-157S S pecifications Product SIP Analog Telephone Adapt er Model VIP-156 VIP-156 PE VIP-157 VIP-157S Hardware LAN 1 x 10/100Mbps RJ-45 port (802.
EC Declaration of Conformity For the following equipment: *T ype of Product : SIP T elephone Adapter *Model Number : VIP-156 * Produced by: Manufacturer‘s Name : Planet T echnology Corp. Manufacturer‘s Address: 1 1F , No 96, Min Chuan Road Hsin T ien, T aipei, T aiwan, R.
Ein wichtiger Punkt beim Kauf des Geräts Planet VoIP Analog Telephone Adapter VIP-157S (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Planet VoIP Analog Telephone Adapter VIP-157S noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Planet VoIP Analog Telephone Adapter VIP-157S - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Planet VoIP Analog Telephone Adapter VIP-157S reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Planet VoIP Analog Telephone Adapter VIP-157S erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Planet VoIP Analog Telephone Adapter VIP-157S besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Planet VoIP Analog Telephone Adapter VIP-157S verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Planet VoIP Analog Telephone Adapter VIP-157S. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Planet VoIP Analog Telephone Adapter VIP-157S gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
