Benutzeranleitung / Produktwartung WGSW-2840 des Produzenten Planet Technology
Zur Seite of 66
24/48-Port 10/100Mbp s + 4G TP/SFP Combo Managed Ethernet Switch WGSW -2840/WGSW-5240 User's Manual.
T rademarks Copyright © PLANET T echnology Corp. 2005. Contents subject to which revision without prior notice. PLANET is a registered trademark of PLANET T e chnology Corp.
T able of Contents 1. INTRODUCTION ................................................................................................................... 5 1.1 P ACKET C ONTENTS ............................................................................
4.4.8 Load Default ........................................................................................................... 28 4.4.9 Reboot ............................................................................................................
1. INTRODUCTION 1.1 Packet Content s Check the contents of your package for following parts: ▫ Ethernet Switch x1 ▫ CD-ROM user's manual x1 ▫ Quick installation guide x1 ▫ 19" rack m.
IEEE 802.3z 1000Base-LX/SX Ethernet standards ▫ High back-plane band width 12.8/17.6Gbp s ▫ Console/Web/SNMP management. ▫ Configuration backup and rec overy . ▫ Per port Ingress/Egress bandwidth restriction. ▫ Configurable spanning tree aging time, STP port configuration.
Management Interface Console/Web/T elnet/SNMP SNMP V ersion v1, v2c Support MIB Support SNMP MIB Ⅱ (RFC 1213), Bridge MIB (RFC 1493), RMON group 1,2,3,9 Enterprise private MIB St andard Compliance Network S tandard IEEE802.3 10Base-T IEEE802.3u 100Base-TX IEEE802.
2. INSTALLATION This section describes the functiona lities of the S witch's components an d guides how to install it on the desktop or shelf. Basic kno wledge of networking is assumed. Please read this chapter com pletely before continuing. 2.1 Product Description 2.
2.1.3 LED Indications WGSW-2840: LED Color Function PWR Green Lights to indicate that the Switch is powered on. SYS Green Lights to indicate the system is working. LNK/ACT Green Blink to indicat e that the switch is acti vely send ing or receiving data over that port.
2.2.1 Desktop Inst allation T o install the Switch on desktop or shelf, please follo ws these steps: Step1: Attach the rubber feet to the recessed areas on the bottom of the switch. Step2: Place the switch on the desktop or the shelf near an AC power source.
Step4: Follow the same steps to attach the second bracket to the opposite side. Step5: After the brackets are attached to the Switch, us e suitable screws to securely attach the brackets to the rack, as shown in Figure 2-6 Figure 2-6 Mounting the Switch in a Rack Step6: Proceeds with the steps 4 and steps 5 of se ssion 2.
3. CONSOLE MANAGEMENT 3.1 Connecting to the Switch The console port is a female DB-9 connector that enables a c onnection to a PC or terminal for monitori ng and configuring the S witch. Use the supplied RS-232 cable with a male DB -9 connector to connect a terminal or PC to the Console port.
type “enable” for further configuration. The system needs password for further configuration. After the “enable” command, the system asks for p ass word, please enter “admin” for the default passw ord. As shows in the following screen: Console login screen 3.
3.4 T elnet login The switch also supports telnet for remote mana gement. The sw itch asks for user name and password for remote login when using telnet, pleas e use “admin” for username and “admin” for password. 3.5 Commands There are two levels for console commands.
show security mac-learning Show port security status show security static-MAC Show static mac table information show snmp Show snmp information show snmp rmon Show snmp rmon state show spantree Show s.
clear security static-MAC Clear static MAC entry clear snmp community Clear snmp community entry clear snmp trap Clear snmp trap management host clear spantree root Restor e spanning tree parame ters .
3.5.2.5 Set command Set command is to change the parameter of the switch functions. The follow table list s the set commands and the equivalent usages.
set qos map vlan-cos-map Set vlan based qos set qos queue egress-polic y Set the egress policy set security MAC-aging Set MAC aging time set security filter-MAC Create MAC filter entry set security ma.
show mirror Show mirror information show multicast router Sho w multicast router port information show port counter Show port counte r information show port rate-shaping Show port ingress and egress r.
4. WEB-BASED MANAGEMENT This section introduces the configur ation and functions of the Web-Based management. 4.1 About W eb-based Management The switch offers management features that allow users to manage the switch from anywhere on the network through a standard bro wser such as Microsoft Internet Explorer .
WGSW-2840 Web Management Interface 4.4 System 4.4.1 IP Configuration The switch can be managed by the Web/T elnet/S NMP interfaces. Administrators can access the management interface via the IP address of the swit ch. The default IP address of the switch is 192.
NOTE: 1. T he Switch’s factory -default IP address is 19 2.168.0.100 with Submask 25 5.255.255.0 a nd a default gateway of 192.168.0.254 2. T he changed IP address take effect immediately af ter click on the OK button, you need t o use the new IP address to access the W eb interface.
message is designed to replace the SNMPv 1 trap message. SNMP community An SNMP community is the group that devices and management stations runn ing SNMP belong to. It helps define where information is sent. The community name is used to identif y the group.
This table is to define the system name, system location and the contact person of the switch. These informations show in the SNMP software of the ma nagement workstation which helps to identify the switch that is looking into.
4. Management S tat ion Configuration A trap manage r is a management station (SNMP applic ation) that receives traps (the system alerts generated by the switch). If no trap manager is def ined, no traps are issued. Create a trap manager b y entering the IP address of the st ation and a community string.
4.4.3 Password The Passwo rd management menu is to set or change the pa ssword of the Web Management Interface. Click on System/Passwo rd menu button, and the Modify Password table shows in the main web page. Enter “old p assword “ , “new password” , “con f irm password” Click “OK” to change the password.
CAUTION: Do not power off the sw itch until the upd ate progress is complete. 4.4.6 Saving Parameters It takes effect i mmediately when you change the parameters of the manag ement function when the switch is running. But the parameters would not be saved after reboot the sw ith.
T o backup the runn ing conf iguration, click on the “Backu p the system’ s p arameters” link, and a pop up window shows to save the configuration of the s witch to your workstation. T o recover a saved config uration, click on the “Browse” button in the Par ameters Recovery table.
4.5 Port Management 4.5.1 Port Configuration This function is to configure and to vie w the configured port management status, port negotiation mode and the port flow control function. 。 Management S tatus : Display port status: Enable or Disab le. Disable is to turn off the port.
4.5.3 Port Band Restrict The function provides the In-B and and Out-Band conn ection speed restriction on the ports. The Band of the connection speed rangs from 64Kbps to 80000Kbps. Ingress Port List/Egress Port L i st field can be filled in distinct number or a port range.
4.6 Redundancy 4.6.1 S p anning T ree 1. Sp anning T ree Protocol The IEEE 802.1D S panning T ree Protocol and IEEE 802. 1W Rapid Sp anning Tree Protocol allow for the blocking of links bet ween switches that form loops within the network. When multiple links bet ween switches are detected, a primar y link is establish ed.
The communication bet ween switches via BPDUs results in the following: 。 One switch is elected as the root switch 。 The shortest distance to the root sw itch is calculated for each switch 。 A designate d switch is selected. This is the switch closest to the root switch through which packet s will be forwarded to the root.
。 From listening to learning or to disabled 。 From learning to for warding or to disabled 。 From forwarding to disabled 。 From disabled to blocking Switch Blocking Listening Learning Forwarding Disable STP Port S tate T ransitions Y ou can modify each port state by using management software.
configurable except by setting priority below) the switch’s MAC address. The Bridge Identifier consists of two parts: a 16-bit priority and a 48-bit Ethernet MAC address 32768 + MAC Priority A relat.
parameters in the Switch are as follows: Priority – A Priority for the switch can be set from 0 to 65535. 0 is equal to t he highest Priority . Hello Time – The Hello T ime can be from 1 to 10 seconds.
Bridge ID = 15 Port 3 Port 1 Port 2 A Bridge ID = 20 Port 1 Port 2 Port 3 C Bridge ID = 30 Port 1 Port 2 Port 3 B LAN 1 LAN 2 LAN 3 Portcast = 19 Portcast = 19 Portcast = 19 Portcast = 4 Portcast = 4 Portcast = 19 Portcast = 4 Portcast = 4 Before Applying the ST A Rules In this example, only the default STP values are used.
between switch B and C is deliberate ly chosen as a 100 Mbps Fast Ethernet link (default port cost = 19). Gigabit ports could be used, but the port cost should be increased from t he default to ensure that the link between switch B and s witch C is the blocked link.
the default setting is 128.The lo wer number has the highest priority . Path Cost: S pecifies the path cost of the port. The switch uses this parameter to help determine which port will become a for warding port. Lower numbers will be used as forwarding ports first.
It allows a maximum of eight ports to be aggregated at the same time. The Sw itch support Gigabit Ethernet ports (up to 12 groups). If the group is defined as a LACP static link aggregationing group, then any extra ports selected are placed in a standby mode fo r redundancy if one of the other ports fails.
applications, which are sensiti ve to even slight delays, or for data from specified end user s whose data transmissions warrant special consideratio n. The Switch allows you to further tailor how priority tagged data packets are handled on your network.
new VLAN is created, the member ports assigned to the new VLAN will be removed from the DEF AUL T _ VLAN port member list. The DEF AUL T_VLAN has a VID = 1.
MAC address. Their presence is indicated by a value of 0x8100 i n the Ether T ype field. When a packet's Ether T ype field is equal to 0x8100, the packet ca rries the IEEE 802.
decisions are based upon this PVID, in so far as VLAN are concerned. T agged packet s are forwarded according to the VID contained within the tag. T agged packets are also assigned a PVID, but the PVID is not used to make packet forwarding decisions, the VID is.
2. The main page then change to Port-base VLAN table, click on the “A dd/Modify” button to create a new VLAN group. 3. The Port-ba se VLAN Confiruta tion table then pops up, enter the VLAN group ID, VLAN name and select the member ports for the VLAN.
802.1Q VLAN There are up to 256 configur able VLAN groups. By default when 802.1Q is enabled, all p orts on the switch belong to default VLAN (VID 1). The default VLAN cannot be deleted. Underst and nomenclature of the S w itch T agging and Untagging Every port on an 802.
Switch allows each port to set one PVID, the range is 1~255, default PVID is 1. The PVID must be the same as the VLAN ID that the por t was defined as belonging to in t he VLAN group, or the untagged traffic will be dropped. 1. Select 802.1Q VLAN in the VLAN T ype field and click on the “OK” button.
3. Choose the Link T ype in the drop drop down menu: A cces s or T runk . Note that if the Acces s type is chosen, it will strip the 802.1 Q t ag from all packets that out of this port.
5.3 Select on the VLAN chich you want to tag with in the VLAN T able field and click o n the “Add” button to add. This will add the VLAN in to the VLAN with The T runk Port field. 5.4 Click on the “close” button to close the VLAN port configur ation table of port #2, and back to the 802.
disconnected or po wered-off from the network, and then reconnected at some time later . If the Net work station is connected with one port want to control the switch, the station’ s MAC Address mus.
3. T o remove the MAC Addre ss filtered by the port. Simply click on the “Delete” button of the MAC Address in the Current Filtering MA C Ta b l e . 4.7.4 MAC Address Learning The switch is able to disable MAC Address learning functio n on ports. 1.
4.7.5 MAC Address Aging T ime The Aging T ime affects the learning process of the S w itch. Dynamic forwarding table entries, which are made up of the source and destination MAC addr esse s and their associated port numbers, are deleted from the table if they are not accessed within the aging time.
4.8 QoS 4.8.1 Underst and QOS Quality of Service (QoS) is an advanced traffic prioriti zation feature that a llows you to establish control over network traffic. QoS enables you to assign various gr ades of network service to different types of traffic, such as multi-media, video, protocol-s pecific, time critical, and file-backup traffic.
Rules are associated with a QoS Profile (see above). T o implement QoS on your network, you need to carry out the follo wing actions: 1. Define a service level to determine the pr iority that will be applied to traffic. 2. Apply a classifier to determine how the incoming traffic will be classified and thus treated by the Swi tch.
2. VLAN-COS Mapping QoS settings allow customization of VLAN ID to T raffic classifiers 1. Fill the VID (1-2094) field in the VL AN-CoS Mapping T able .
3. 802.1p-CoS Mapping QoS settings allow customization of packet priority in order to facilitate delivery of data traf fic that might be affected by latency problems. The IEEE 802.1p Priority specification uses 8 priorit y levels to classify data packet s.
4. Port-COS Mapping QoS settings allow customization of VLAN ID to T raffic classifiers 1. Fill the Port List (e.g. 1-3,7) field in the port-based QoS Configuration T able. 2. Fill the mapping number in the CoS (0-7) field. 3. Click on the “OK” button to save.
6. Queue Management There are two rules for the Priorit y Queue: Weighted Round Robin ( WRR ) and Al ways Hight . T o configure Queue Rul e, select the Queue Policy drop down menu in the Queue Rule Configuration table. And Click on the “OK” button to save.
4.9 Multicast 4.9.1 IGMP Snooping Theory Computers and network devices that want to re ceive multicast transmissions ne ed to inform nearby routers that they will become mem bers of a multicast gro up. The In ternet Group Management Protocol (IGMP) is used to communicate this information.
A host sends an IGMP “report” to join a group A host will never send a report when it wants to leave a group (for version 1). A host will send a “leave” report when it wants to leave a group (for version 2). Multicast routers send IGMP queries (to the all-host s group address: 224.
4.9.2 St atic Routing Port This function is to configure ports to be the member of IGMP Group s in VLANs. T o do this, fill the Port List field and the VID field for the static routing and click on the “Add ” button to save. 4.10 Port Analysis 4.10.
4.10.2 Port Mirror Port Mirroring is a method of monitoring network traf fic that forwards a copy of each incoming and/or outgoing packet from one port of a network switch to another port where the packet can be studied. It enables the manager to keep close track of s w itch performance and alter it if necessary .
4.1 1 Storm Control This function is to control the Braodcast S torm, Mu lticast S torm and Flooded S torm packet on each port. T o configur e the S torm Control, click on the Storm Control menu button. The web main page then sho ws the S trom Restricting function table.
5. TROUBLE SHOOTING This section is intended to help you solve the most common problems on the 8 10/ 100TX plus 100FX Exp. Slot managed POE switch. 5.1 Incorrect connections The switch port can auto detect straight or crossove r cable when you li nk switch with other Ethernet device.
5.2.1 Cabling RJ-45 ports: use unshielded twisted-pair (UTP) or shie ld twisted-pair (STP) cable for RJ-45 connections: 100 Ω Category 3, 4 or 5 cable for 10Mbps connections or 100 Ω Category 5 cable for 100 Mbps connections. Also be sure that the length of any tw isted-pair connection does not excee d 100 meters (328 feet).
6. APPENDIX 6.1 Console Port Pin Assignment s The DB-9 serial port on the front panel is used to connect to the switch for out-of-band console configuration. The console menu-dr iven configuration progr am can be accessed from a terminal or a PC running a terminal emulation p rogram.
Cable Ty p e Max. Length Connector 10BASE-T Cat. 3, 4, 5100-ohm UTP 100 m (328 ft) RJ-45 100BASE-TX Cat. 5 100-ohm UTP 100 m (328 ft) RJ-45 100BASE-FX 50/125 or 62.
Ein wichtiger Punkt beim Kauf des Geräts Planet Technology WGSW-2840 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Planet Technology WGSW-2840 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Planet Technology WGSW-2840 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Planet Technology WGSW-2840 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Planet Technology WGSW-2840 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Planet Technology WGSW-2840 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Planet Technology WGSW-2840 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Planet Technology WGSW-2840. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Planet Technology WGSW-2840 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
