Benutzeranleitung / Produktwartung WAP-4033PE des Produzenten Planet Technology
Zur Seite of 38
54Mbps PoE Access Point WAP-4033PE User’s Manual.
Copyright Copyright © 2006 by PLANET T echnology Corp. All rights reserved. No part of this publication m ay be reproduced, transmitted, transcri bed, stored in a retriev al system, or translated int.
interference received, including interfer enc e that may cause undesired operatio n. Federal Communication Commissi on (FCC) Radiation Exposure St atement This equipment complies with FCC radiation expos ure set forth for an uncontrolled envir onment.
Revision User ’s Manual for PLANET 54Mbp s PoE Access Point Model: W AP-4033PE Rev: 1.0 (Oct, 2006) Part No. EM-W AP4033PE 4.
T ABLE OF CONTENTS Chapter 1 Introduction .................................................................................. 7 1.1 Package Contents .................................................................................................... 7 1.
Chapter 4 Specification ............................................................................... 36 Chapter 5 Frequently Ask Question ..........
Chapter 1 Introduction Thank you for purchasing WAP-4033PE. The W AP-4033 PE supports both IEEE 802.1 1b a nd IEEE 802.1 1g standards. Y ou can use it to connect an existi ng WLAN, or to build up a new wireless LAN.
1.3 Features z Complies with the IEEE 802.1 1b/g (DSSS) 2.4GHz specification z Supports 2.400~2.4835 GHz frequency b and z Data rate supports up to 54Mbps z IEEE 802.
microwave ovens, heavy-dut y motors, fluorescent lig hts and other i ndustrial equipments. Keep the number of walls or ceilings between AP and clients as few as possible. Otherwise the signal strength may be seriously reduced. Place WAP-4033PE in a open space or add additional W AP-4033PE as needed to improve the covera ge.
Chapter 2 Hardware Installation Before you proceed with the installation, it is nec essary that you have enoug h information about the W AP-4033PE. 1. Locate an optimum lo cation for the W AP-4033PE. T h e b e s t place for your W A P-4033PE is usually at the center of your wireless network, with line of sight to all of your mobile stations.
Chapter 3 Web Configuration Web configuration provides a user-friendly graph ic al us er interface (web pages) to manage yo ur W AP-4033PE. An AP with an assigned IP address (e.g. http://192.168.0.1 ) will allow you to monitor and configure (via web browser e.
3.2 Basic Setting In this option, you can configur e W AP-4033PE to work to different operating mode. Please refer to below sections to know the details configuration of each operating mo de. 3.2.1 AP Mode This mode is set to W AP-4033PE b y defa ult.
Parameter Description Mode Shows the current operation mode. You ma y set WAP-4033PE to other operating mode by select other operatin g mode. Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate up to 54Mbps.
work. You may check the LED status to make sure WAP-4033PE is finish the restart. 3.2.2 Station - Ad Hoc Mode Served as a w ireless station (Ad-h oc). Connected to a PC or a small LAN, this st ation along with other wireless stations can establish a small wireless net work without Access Points.
Parameter Description Mode Shows the current operation mode. You may set WAP-4033PE to other operating mode by select other oper ating mode. Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate up to 54Mbps.
3.2.3 Station - Infrastructure Mode Served as a wireless station (infrastructure). Con nected to a PC or a sma ll LAN, it allows the PC or small LAN able to access the wireless net work via Access Point. Parameter Description Mode Shows the current operation mode.
3.2.4 AP Bridge - Point to Point Mode This function provides to bridge for 2 wired Ethernet networks to connect to each other b y wireless. You can use t wo WAP-4030s in this mode to connect two wired Ether net networks together. Parameter Description Mode Shows the current operation mode.
to configure the detail settings. After configuration complete, pleas e click “Apply” button to save the configu ration. Then you will see a screen to prompt you the settings are save successfully. You may press “Co ntinue” for configure other settings or “Apply” to re start WAP-4033PE with new configurati on.
AP MAC Address If you want to bridge more than tw o wired Ethernet net works together with wireless connection, you hav e to enter the MAC a ddr esses of other WAP-4033PEs that with join the bridging work into the fields. Set Security IF you want to ena ble security to protect your wireless connection.
Band 2.4GHz (B): It allows to select the transmit rate up to 11Mbps. 2.4GHz (G): It allows to select the transmit rate up to 54Mbps. 2.4GHz (B+G): It provides best performance for 11g transmission when yo u enable the AP mode selection to “Mixed mode”.
see a screen to prompt you the settings are save successfully. You may press “Co ntinue” for configure other settings or “Apply” to re start WAP-4033PE with new configurati on. 3.2.7 Universal Repeater Mode “Universal Repeater Mode” allo ws you to extend the rang e of your wireless net work.
same. The default SSID is “ default ”. Channel Number Select the appropriate chan nel from the list provided to corresp ond with your network settings.
Parameter Description Encryption Y ou can select “None”, “ WEP 64bits”, “WEP 128bits”, “WP A (TKIP)” or “WP A2 (AES)” of this option . In default, it is None. Key Format This is only used when you select “ WEP 64bits” or “WEP 128bits” encryption method.
the bridged access points. F ill the text box b y following the rules belo w . Hex (64 characters): input 64-digit Hex values (i n th e “A-F”, “a-f” and “0-9” range) or at least 8 character pass phrase as the pre-shared keys. After configuration complete, pleas e click “Apply” button to save the configur ation.
fragmentation of data to be transmitted. If you set this value too low , it will result in bad performance. RTS Threshold When the packet size is smalle r than the R TS threshold, the access point will not use the RTS/CTS mechanism to send this packet.
mode”. The security settings only apply to AP function in “Universal Repeater mode”. The station function of “Universal Repeater mode” does not have security feature. 3.4.1 802.1x IEEE 802.1x is an authentication pr ot ocol. Every user must use a valid ac count to login to this Access Point before accessing the wireless LAN.
802.1x only, please keep this setting in “Disa ble”. Enable 802.1x Authenticatio n Please check this opti on to en able 802.1x function. RADIUS Server IP Address Enter RADIUS Serer IP address. RADIUS Server Port Leave the default port setting or assign a new port number for this option.
WEP key length will provide higher level of securit y , but the throughput will be lower . Key Format Y ou may select to select ASCII Characters (alphanumer ic format) or Hexadecimal Digits (in the “A-F”, “a -f” and “0-9” range) to be the WEP Key .
Parameter Description Encryption Please select “WPA pre-shar ed ke y” in this option. WP A (TKIP) TKIP can change the encryption key frequen tly to enhance the wireless LAN security . WP A2 (AES) This use CCMP protocol to change encryption key frequently .
3.4.4 WPA RADIUS WiFi Protected Access (WP A) is an advanced se curity standard. Y ou c an use an external RADIUS server to authenticate wireless stati ons and provide the session key to encrypt data during communication. It uses TKIP or CCMP (AES) to change the enc r yption key frequently .
3.5 MAC Filtering For security reason, the MAC Address Filterin g that only allo ws authorized MAC Addresses associating to the Access Point. Parameter Description Enable Wireless Access Control Enable or disable the MAC Address Filterin g function.
3.6 System Utility From here, you can define th e Access Point’s IP Address and Login Password and enable the Access Point to be a DHCP Server . Parameter Description Password Settings Current Password Enter the current password (up to 15-digit alphanumeric string) of the Access Point.
the Access Point is 255.255.255.0 . Gateway Addr ess The IP address of the default gat eway of the subnet that this access point resides in. It allows this access point be accessed by PC from deferent subnet to do configuration. DHCP Server Enable or disable the DHCP Server .
Parameter Description Configuration T ools Use the " Backup " tool to save the Access Point’ s current configuration to a file named "config.bin" on your P C. Y ou can the n use the " Restore " tool to upload and restore the saved config uration to the Access Point.
Parameter Description Firmware Upgrade This tool allows you to upgrade the Access Point’s system firmware. T o upgrade the firmware of WAP-4033PE, y ou nee d to download the firmware file to your local hard disk, and enter that file name an d p ath in the app ropriate field on this page.
Chapter 4 Specification Standard IEEE 802.11g / 802.11b Frequency Band 2.400~2.4835GHz Transfer Rate 802.11g: 54/48/36/24/18/ 12/9/6Mbps 802.11b: 11/5.5/2/1Mbps Modulation OFDM, CCK, DQPSK and DBPSK Sensitivity 1 1g @ PER < 10% 54Mbps: -71.46 dBm 48Mbps: -73.
Chapter 5 Frequently Ask Question This chapter provides ans wer to problems usually encountered during th e installation and operation o f the Wireless Network Access Point . Read the descri ption below to solve your problems. Q. Can I run an application from a remo te computer over th e w ireless network? A.
Q. When WA P-4033PE works with WDS m ode, can wireless connect to it? A. Y es, WDS mode is work as a AP and Bridge at the same time. So the wireless client can access to WDS mode W AP-4033PE without problem. When wireless client connect to the remote site via WDS mode, the performance will be 50% then ac cess to the connected WDS mode W AP-4033PE.
Ein wichtiger Punkt beim Kauf des Geräts Planet Technology WAP-4033PE (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Planet Technology WAP-4033PE noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Planet Technology WAP-4033PE - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Planet Technology WAP-4033PE reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Planet Technology WAP-4033PE erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Planet Technology WAP-4033PE besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Planet Technology WAP-4033PE verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Planet Technology WAP-4033PE. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Planet Technology WAP-4033PE gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
