Benutzeranleitung / Produktwartung KBD4000 des Produzenten Pelco
Zur Seite of 43
ADDENDUM Worldwide Headquarters • 3500 Pelco W ay • Clovis, California 93612 USA • www .pelco.com USA & Canada • T el: 800/289-9100 • Fax: 800/289-9150 International • T el: 1-559/292-1981 • Fax: 1-559/348-1120 Addendum No.
KBD4000 Genex ® Multiplexer Keyboar d Installation/ Operation Manual C1921M-G (1/04) ® Pelco World Headquarters • 3500 Pelco Way, Clovis, CA 93612-5699 USA • www.
2 Pelco Manual C1921M-G (1/04).
Pelco Manual C1921M-G (1/04) 3 LIST OF TABLES T able Page A Camera Numbers with Switch 7 ON .......................................................................... 7 B Keyboard Addresses .............................................................
4 Pelco Manual C1921M-G (1/04) IMPOR T ANT SAFEGUARDS AND W ARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.
Pelco Manual C1921M-G (1/04) 5 DESCRIPTION The KBD4000 Genex ® Multiplexer Keyboard is a full-function keyboard controller for the MX4000 Genex Multiplexer and MX4000SVR Genex Multiplexer Server . This manual covers the KBD4000 keyboard’s operation with both duplex and simplex models of the multiplexer .
6 Pelco Manual C1921M-G (1/04) Figure 1. Connecting Keyboard to Multiplexer 1. Remove the DIP switch cover plate from the rear of the keyboard (refer to Figure 1). 2. Set the switches (refer to Figure 1 for switch locations). ADDRESS Set switches 1, 2, and 3 OFF .
Pelco Manual C1921M-G (1/04) 7 UNUSED Leave switch 5 OFF . It is not used. TURBO MODE Set switch 6 ON to enable the turbo (extra fast) pan feature or OFF to disable. CAMERA ADDRESS MODE There are two modes for addressing cameras: • Set switch 7 ON if you want to address all cameras consecutively from 1-256 (refer to T able A).
8 Pelco Manual C1921M-G (1/04) 1B DO A MUL TIPLEXER SERVER MODE INST ALLA TION R+ R- T T+ LOCAL KEYBOARD ON 1234567 ON 1234567 ON 1234567 ON 1234567 1 TX+ 2 TX- 3 12V AC 4 12V AC 5 GND 6N C 7 RX- 1 TX.
Pelco Manual C1921M-G (1/04) 9 3. Replace the cover on the back of the keyboard. 4. Connect the keyboard to the MX4000SVR Multiplexer Server . Y ou can connect up to four keyboards to the server—one to the server ’s LOCAL KEYBOARD port and three to its REMOTE KEYBOARD(S) port, or all four to the remote.
10 Pelco Manual C1921M-G (1/04) NOTE: If you have a multi- plexer server , you must en- ter the Camera menu from the multiplexer ’s front panel. Then you can program the cameras from the front panel of the multiplexer or from the keyboard.
Pelco Manual C1921M-G (1/04) 11 IMPORT ANT : The Genex multiplexer lets you work in any of four languages: English (default), French, German, or Spanish. If you need to change the lan- guage, do so before pro- gramming because you must reset the multiplexer to factory defaults before you can change the language.
12 Pelco Manual C1921M-G (1/04) MENUS Figure 4. Menu T ree Press and hold the VIEW key to switch to the System Setup menu. Enter a camera number and then press and hold the CAM key to change to the Camera menu. Press and hold the SEQ key to switch to the Sequence menu.
Pelco Manual C1921M-G (1/04) 13 SYSTEM SETUP (VIEW KEY) 2/6/8 Hr 2/6/8 Hr MAIN MONITOR VIDEO RESET A CTIVITY DETECTION ALL CH T O *2,6,or 8 Hr 120 Hr 12 Hr 168 Hr 16 Hr 180 Hr 18 Hr 240 Hr 24 Hr 360 H.
14 Pelco Manual C1921M-G (1/04) Record Speeds Sets the speed at which the VCR normally records video and at which it records when there is an alarm(s). Setting the speeds in the System Setup menu also sets the speeds in the Record Setup and Custom VCR Setup menus.
Pelco Manual C1921M-G (1/04) 15 ADV ANCED SYSTEM SETUP (VIEW KEY) ALL COLOR* COLOR & B/W RESERVED DA TE FORMA T MM-DD-YY P ASSWORD DISABLED FRONT P ANEL CONTROL ENABLED MAIN MONITOR DISPLA Y RESPONDS TO NONE SPOT MONITOR DISPLA Y SEQUENCE RESPONDS TO ALARMS AUX MONITOR DISPLA Y BLANK RESPONDS TO ACTIVITY CAMERA TYPES ALL COLOR UNIT ID 001 COMM.
16 Pelco Manual C1921M-G (1/04) Spot Monitor Display • Select BLANK, SEQUENCE, or TRACK MAIN if you want the spot monitor to switch to cameras that have alarms or activity detection. Then under RE- SPONDS T O, select ALARMS, ACTIVITY , or ALARMS/ACTIVITY .
Pelco Manual C1921M-G (1/04) 17 Comm. T ype • In polled communication mode (switch 4 off), one multiplexer (any one) must be the master . Only one multiplexer can be master; all others must be slaves. The master multiplexer communicates with the slave multiplexers.
18 Pelco Manual C1921M-G (1/04) RECORD SETUP (LIVE/VCR KEY) ALARM DURA TION 30 SECONDS 1 MINUTE 2 MINUTES 5 MINUTES 10 MINUTES 15 MINUTES ENABLED + ENABLED - DISABLED *2, 6, or 8 Hr 24 Hr 96 Hr 240 Hr.
Pelco Manual C1921M-G (1/04) 19 VCR Switch Pulse • ENABLED + means the multiplexer waits for a positive head switching pulse from the VCR. If the multiplexer does not get a pulse from the VCR (because of a broken wire or the VCR does not give a pulse in some modes), it may appear the multiplexer is not working properly .
20 Pelco Manual C1921M-G (1/04) CUSTOM VCR SETUP (LIVE/VCR KEY) Figure 8. Custom VCR Setup Menu To program the advanced VCR parameters: 1. Press the MAIN MONITOR key .
Pelco Manual C1921M-G (1/04) 21 CAMERA SETUP (NUMBER AND CAM KEYS) OPEN CLOSED VIDEO INPUT TERMINA TION 75 OHM ALARM INPUT NORMALL Y OPEN COAXITR ON FORMA T EXTENDED ACTIVITY DETECTION ENABLED SET DETECTION MASK ENABLED DISABLED * * ONL Y NINE CHARACTERS APPEAR WHEN IN THE 16-CAMERA DISPLA Y .
22 Pelco Manual C1921M-G (1/04) (If you play back the tape on the same equipment, any covert picture will still appear blanked. Change the setting to NORMAL to see the picture.) V ideo T ermination • Set to 75 OHM when equipment is connected to the video IN connector only .
Pelco Manual C1921M-G (1/04) 23 ACTIVITY DETECTION MASK SETUP ACTIVITY DETECTION MED SENSITIVITY SET ALL CLEAR ALL EXIT TEST ACTIVITY BOX SET ACTIVITY BOX CLEAR LOW SENSITIVITY MED SENSITIVITY HIGH SENSITIVITY Figure 10. Activity Detection Mask Activity detection continually monitors selected camera inputs for motion.
24 Pelco Manual C1921M-G (1/04) 7. T urn activity boxes on or off (the default is all are on). • To turn on all boxes , use the joystick to choose SET ALL. Press the OPEN key . All boxes contain a symbol (as shown in Figure 10). The multiplexer monitors activity in those boxes.
Pelco Manual C1921M-G (1/04) 25 3. Press the SEQ key for about three seconds. 4. T ype the password (3916), if requested. Enter it by pressing each number key followed each time by the CAM key . The Sequence menu appears. The currently selected menu item blinks.
26 Pelco Manual C1921M-G (1/04) MUL TIPLE CAMERA DISPLA Y SETUP Y ou can use the keyboard to configure multiple camera display formats. The LEDs above the camera buttons on the multiplexer light to indicate which cameras are being displayed.
Pelco Manual C1921M-G (1/04) 27 PROGRAMMING THE 9-CAMERA DISPLA Y ( ) Y ou can program two groups of nine cameras each. Both groups can be programmed to include any nine cameras. is unavailable in simplex record mode. To program the nine-camera displays: 1.
28 Pelco Manual C1921M-G (1/04) PROGRAMMING MENU DEF AUL TS T able D. Programming Menu Defaults Menu Item Default System Setup T ime Display On T itle Display On Normal Record Speed 2/6/8 Hr (NTSC/EIA.
Pelco Manual C1921M-G (1/04) 29 PROGRAMMING A PRESET 1. Press the MAIN or SPOT MONIT OR key . The green LED over the MAIN or SPOT key lights. When using the MAIN MONITOR, the SPOT MONITOR DISPLA Y menu item in the Advanced System Setup menu must be set to TRACK MAIN (refer to the Advanced System Setup section).
30 Pelco Manual C1921M-G (1/04) 1. LED DISPLA Y Displays the address of the multiplexer (from 1-16) with which the keyboard is communicating. 2. LIVE/VCR KEY Selects the source of video to display on the monitor(s). LIVE is live video from the cameras.
Pelco Manual C1921M-G (1/04) 31 T able E. Operation Guide Refer to “Functions” in the Index for an alphabetical list of the operations described in T able E. NOTE: References to switch 7 in this table refer to the switch behind the panel on the back of the keyboard.
32 Pelco Manual C1921M-G (1/04) Exits main tracking mode. 1. Go to the Advanced System Setup menu. 2. Move the joystick so the cursor highlights SPOT MONIT OR DISPLA Y items. 3. Press the OPEN key until SEQUENCE or BLANK is displayed. 4. Exit the Advanced System Setup menu.
Pelco Manual C1921M-G (1/04) 33 Zoom on a camera on the main monitor . 1. Press the MAIN MONITOR key . The green LED over the MAIN key lights. 2. Select the camera.
34 Pelco Manual C1921M-G (1/04) 1. Press the SPOT MONIT OR key . The green LED over the SPOT key lights. 2. Select a camera on the multiplexer you want to sequence.
Pelco Manual C1921M-G (1/04) 35 1. Follow the steps under “Run a sequence of cameras from one multiplexer on the main monitor” or “Run a sequence of cameras from one multiplexer on the spot monitor” to start sequencing the cameras on the main and spot monitors of individual multiplexers you want to sequence.
36 Pelco Manual C1921M-G (1/04) 1. Press the SPOT MONIT OR key . The green LED over the SPOT key lights. 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) a. On the number pad, press the multiplexer ’s address number (1-16 if the keyboard is connected to the multiplexer; 1-8 if connected to a server), and then press the UNIT key .
Pelco Manual C1921M-G (1/04) 37 T able E. Operation Guide (Continued) OPERA TION KEYBOARD COMMAND RESUL T The auxiliary function operates. 1. Press the SPOT MONIT OR key . The green LED over the SPOT key lights. 2. Select the camera. Addressing by Multiplexer (Switch 7 OFF) a.
38 Pelco Manual C1921M-G (1/04) TROUBLESHOOTING If you have difficulty operating your system, run through the following checklist to see if you can solve the problem. 1. Are the keyboard switches set properly? 2. Is the equipment wired properly? 3. Are the menu options in the multiplexer(s) and server set properly? 4.
Pelco Manual C1921M-G (1/04) 39 16. If you have a server , each keyboard controls its corresponding monitors. • In SINGLE mode, keyboard 1 controls monitor 1, keyboard 2 controls monitor 2, etc. • In P AIRED mode, keyboard 1 controls monitor 1 (main) and monitor 2 (spot), and keyboard 3 controls monitor 3 (main) and monitor 4 (spot).
40 Pelco Manual C1921M-G (1/04) INDEX A Activity detection 14 Activity detection mask setup 23 Address setting 9 Address switch setting 6, 8 Addressing by multiplexer 21, 23, 29 Addressing consecutive.
Pelco Manual C1921M-G (1/04) 41 O Operating differences 5 Operating modes 5, 6 P Paired mode 9 Password 1 1, 15 Pattern programming 29 Playback format 19 Polled/non-polled communication 9 Polled/non-p.
42 Pelco Manual C1921M-G (1/04) REVISION HISTOR Y Manual # Date Comments C1921M 5/98 Preliminary version released for beta evaluation. 7/98 Original version. C1921M-A 12/98 Added Sections 5.0 through 5.4. Added note to section 3.1. Added operations to T able C.
Ein wichtiger Punkt beim Kauf des Geräts Pelco KBD4000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Pelco KBD4000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Pelco KBD4000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Pelco KBD4000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Pelco KBD4000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Pelco KBD4000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Pelco KBD4000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Pelco KBD4000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Pelco KBD4000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
