Benutzeranleitung / Produktwartung ES31PC des Produzenten Pelco
Zur Seite of 68
ES30PC/ES31PC Esprit ® with Pressurized IOC C311M-L (1/05) ® INST ALLA TION/OPERA TION U.S. Patent D-472.260.
2 C311M-L (1/05) CONTENTS Section Page IMPORT ANT SAFETY INSTRUCTIONS .................................................................................................. ............................................................................. 5 DESCRIPTION .
C311M-L (1/05) 3 GAIN/AGC ................................................................................................................................................................................................................ 34 IR FIL TER MODE (MODELS ES30PCBW18/ES31PCBW18 ONL Y) .
4 C311M-L (1/05).
C311M-L (1/05) 5 IMPORT ANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
6 C311M-L (1/05) DESCRIPTION The ES30PC/ES31PC Esprit Series is designed to protect camera optics and electronics from moisture and airborne contaminants. The system features a receiver , pan and tilt, enclosure, and a pressurized integrated optics cartridge (IOC).
C311M-L (1/05) 7 INST ALLA TION When installing the ES30PC/ES31PC Esprit ® system, allow for sufficient clearance between the top of the unit and overhead obstructions. This will prevent interference when the enclosure is driven to its maximum elevation of 33 degrees.
8 C311M-L (1/05) Route the wires and cables through the center of the Esprit mount. Reinstall the transformer module into the base. The transformer module can be positioned in the mount base in only one orientation. ES30PC-5/ES31PC-5 Models Only – Set the 120/230 voltage selector switch on the transformer to the appropriate voltage.
C311M-L (1/05) 9 Tu rn on the power . If the red LED lights, turn off the power and proceed to the next step. If the red LED does not light, refer to the Tr oubleshooting section. Plug the male Esprit system connector , located on the bottom of the pan and tilt, into the female Esprit system connector locat ed on the transformer module.
10 C311M-L (1/05) TXB SERIES TRANSLA TOR BOARD INST ALLA TION (OPTIONAL) Pelco’ s TXB Series allows controllers from other companies to communicate with the Esprit system.
C311M-L (1/05) 11 HOW TO REINST ALL THE PAN AND TIL T COVER The pan and tilt covers must be properly seated and have a tight seal all the way around when installed. To reinstall the pan and tilt cover , do the following: 1. Properly position the cover and slide it into place.
12 C311M-L (1/05) OPERA TION POWER-UP DISPLA Y When the system is powered up, the selected protocol, revision number , and other information is displayed on the monitor . For e xample, the screen might show the following information: The information displayed depends on the selected protocol (C, D, or P) and the menu selection for power - up mode.
C311M-L (1/05) 13 PRESSURIZED INTEGRA TED OPTICS CARTRIDGE The pressurized IOC houses an auto focus camera, lens, heater , and sensors in a self-contained, sealed unit. Dry nitrogen pressurized to 10 psig controls the environment inside the cartridge, eliminating internal condensation and corrosion.
14 C311M-L (1/05) CURRENT READING MENU The Current Reading menu displays the existing status of temperature, pressure, and dewpoint inside the integrated optics cartridge. An asterisk displayed to the left of a menu item denotes that an alert condition exists.
C311M-L (1/05) 15 ZONES A zone is a programmed pan area with set boundaries and identifying label. The Esprit system has a maximum of eight zones, each with a 20-character label. Zones can be programmed to blank video when the camera pans into the zone area.
16 C311M-L (1/05) PROGRAMMING – ES30PC16/ES31PC16 Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu Line Sync On Line Sync Phase 0 Exit Line Sy.
C311M-L (1/05) 17 PROGRAMMING – ES30PC22/ES31PC22 Gain Limit 7 Exit Gain/AGC Menu Auto-iris mode Auto Auto-iris level 66 Auto-iris peak 16 Exit Auto Iris Menu LowLight limit 2 Shutter speed Auto Aut.
18 C311M-L (1/05) PROGRAMMING – ES30PCBW18/ES31PCBW18 Gain Limit 28 Exit Gain/AGC Menu Auto-iris mode Auto Auto-iris level 91 Auto-iris peak 16 Exit Auto Iris Menu LowLight limit 2 Shutter speed Aut.
C311M-L (1/05) 19 PROGRAMMING ACCESSING MAIN MENU (PRESET 95) Y ou can call up the main menu on your monitor by programming (setting or creating) preset 95 (28 if in 32-preset mode). Programming preset 95 for Pelco’ s controllers varies according to the type of controller you are using.
20 C311M-L (1/05) ACK ACT (ACKNOWLEDGE ACTION) If an enivornmental condition inside of the IOC goes outside of the factory set limits (such as “Low Pressure”) then select ACK Alert to activate the alert label behavior . Program ACK Act to establish alert label behavior after alert acknowledgement.
C311M-L (1/05) 21 ALERT DISPLA Y POSITION Screen positioning of the alert label is user -defined. Positioning options include the following: To set the alert label position: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Alert.
22 C311M-L (1/05) ALERT REPEA T Y ou can program how often an ALERT label is repeatedly displayed until it is acknowledged by the system controller . The followi ng settings are available: Constant The ALERT label is continually displayed on the monitor until acknowledged.
C311M-L (1/05) 23 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camer.
24 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camer.
C311M-L (1/05) 25 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camer.
26 C311M-L (1/05) AUTO SHARPNESS <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x.
C311M-L (1/05) 27 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
28 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
C311M-L (1/05) 29 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
30 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camer.
C311M-L (1/05) 31 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
32 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
C311M-L (1/05) 33 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
34 C311M-L (1/05) GAIN LIMIT The gain limit sets the maximum level for the automatic gain control. Increasing the level will increase the signal level and increase the noise level of the picture. To change the gain: 1. Program preset 95 (28). The main menu appears.
C311M-L (1/05) 35 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camer.
36 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Limit Stops Off Set Man Limits Clear Man Limits Set Scan Limits Clear Scan Limits Exit Limit Stop Menu LIMIT STOPS NOTE: Limit stops are inactive while setting items in the program menu (e.
C311M-L (1/05) 37 LIMIT STOPS MENU The manual pan limit stops can be set at the controller using the Limit Stops menu: 1. Program preset 95 (28). The main menu appears. 2. Position the cursor (>) beside Limit Stop. 3. Press the Iris Open button to enter the Limit Stop menu.
38 C311M-L (1/05) Scan Limit Stops When scan limit stops are set, the pan and tilt reverses direction during random, frame, or auto scanning when a limit stop is reached.
C311M-L (1/05) 39 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Line Sync On Line Sync Phase 0 Exit Line Sync .
40 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camer.
C311M-L (1/05) 41 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
42 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 90 MPH wind Exit Other Menu PA TTERN LENGTH The Esprit can do the following: One full pattern - 1.
C311M-L (1/05) 43 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Power Up Default Exit Power -Up Menu POWER-UP MODE This feature lets the dome resume a desired condition following power -up.
44 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
C311M-L (1/05) 45 Default Setting <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camera <Gain/AGC> <Auto iris> Next Exit Camera Menu RESET CAMERA Resetting the camera returns the settings to their defaults.
46 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.5 min Spd Profile 50 MPH wind Exit Other Menu SCAN SPEED The scan speed is adjustable from 1-40 degrees per second.
C311M-L (1/05) 47 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camer.
48 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camer.
C311M-L (1/05) 49 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
50 C311M-L (1/05) Auto white bal On Red bal level 182 Blue bal level 182 Exit White Balance Menu <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Ot.
C311M-L (1/05) 51 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Wiper Mode Momentary Wiper Dwell <s> 2 Wiper T ime <m> 60 Exit Wiper Menu WIPER MODE There are three wiper settings: Wiper Mode Wiper Dwell Wiper T ime To change the wiper settings: 1.
52 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
C311M-L (1/05) 53 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
54 C311M-L (1/05) <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Backlight comp Off Zoom limit x- - Reset camer.
C311M-L (1/05) 55 <Camera> <Line Sync> <Power Up> <Wiper> <Limit Stop> <Alert> <Other> ACK Alert Exit MAIN MENU Proportional pan On Park time minutes 0 Scan Speed deg/s 25 Pattern Length 1.
56 C311M-L (1/05) TROUBLESHOOTING NOTE: The system contains no user -serviceable parts. If there is a problem with your system, it must be returned to Pelco for servicing.
C311M-L (1/05) 57 Symptom: No video or poor video 1. Check the video and power connections to the camera. 2. Check for power to the camera from the Esprit system camera power output. 3. Check all coax BNC connectors from the camera to the monitor . 4.
58 C311M-L (1/05) MAINTENANCE Clean the enclosure window periodically with a mild non-abrasive detergent in water and a soft cloth to help maintain picture clarity . If operating problems are experienced with the system, refer to the T roubleshooting section.
C311M-L (1/05) 59 00864 2. Open hinge door to the system. Remove the cap screw that secures the wiper board. Unplug the ribbon cable connector . 00866 RIBBON CABLE CONNECTO R CAP SCREW 00865 3. Lift up wiper board and unplug the cartridge power cables.
60 C311M-L (1/05) APPENDIX NOTE: Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode.
C311M-L (1/05) 61 Table B. Switch Settings for SW2 NOTE: The Esprit will sense and automatically select input from Coaxitron control signals in either the standard or extended mode. Therefore, the DIP switches settings have no effect on Coaxitron control signals.
62 C311M-L (1/05) Table B. Switch Settings for SW2 (Continued) (Continued on next page) Receiver Address Switch Setting P-T ype D-T ype Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 .
C311M-L (1/05) 63 Table B. Switch Settings for SW2 (Continued) Receiver Address Switch Setting P-T ype D-T ype Control Control SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8 – 232 OFF OFF OFF ON OF.
64 C311M-L (1/05) SPECIFICA TIONS ELECTRICAL Input V oltage: 24, 120, or 230 V AC, 50/60 Hz; switch selectable for 120/230 VAC inputs. Reset featur e enabled when power becomes unstable or interrupted.
C311M-L (1/05) 65 Sensitivity ES30PC16/ES31PC16: 0.05 lux at 1/2-second shutter speed (NTSC) 0.05 lux at 1/1.5-second shutter speed (P AL) ES30PC22/ES31PC22: 0.02 lux at 1/2-second shutter speed (NTSC) 0.02 lux at 1/1.5-second shutter speed (P AL) ES30PCBW18/ES31PCBW18: 0.
66 C311M-K (9/04).
REVISION HISTORY Manual # Date Comments C311M 6/01 Original version. C311M-A 8/02 Camera modifications. C311M-B 9/02 Revised per ECO #02-8063. C311M-C 11/02 Revised installation instructions for addition of alignment label. C311M-D 6/03 Added Az/El/Direction menu per ECO #03-8861.
W orldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
Ein wichtiger Punkt beim Kauf des Geräts Pelco ES31PC (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Pelco ES31PC noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Pelco ES31PC - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Pelco ES31PC reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Pelco ES31PC erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Pelco ES31PC besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Pelco ES31PC verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Pelco ES31PC. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Pelco ES31PC gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
