Benutzeranleitung / Produktwartung C1306M des Produzenten Pelco
Zur Seite of 24
ExSite ™ EHXM Series Explosionproof Fixed System INSTALLATION C1306M (8/05).
2 C1306M (8/05) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Getting Started .
C1306M (8/05) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’ s instructions.
4 C1306M (8/05) Getting Started Thank you for purchasing Pelco’ s ExSite ™ EHXM Series explosionproof system. This manual includes instructions for installing all the components of the system. Once the system installation is complete, refer to the operation/programming manual for instructions on how to operate and pro- gram your system.
C1306M (8/05) 5 Install the Power Module Attach the power module to the mounting surface. Use only installation methods and materials capable of supporting four times the maximum specified load of the system (140 lb/63.5 kg). NOTE: If required, install the optional TXB translator , fiber module, or UTP board before installing the power module.
6 C1306M (8/05) CONNECT WIRING Refer to the following information to connect the wires and cables as required. NOTES: • Relay 3 is allocated specifically for an external washer (not supplied by Pelco). • All relays are specified for 32 VDC, 0.5 A.
C1306M (8/05) 7 DIP SWITCH SETTINGS Configure the receiver address, termination, and baud setting for the system. The DIP switches to configure these settings are located on the top of the power module. NOTE: No DIP switch settings are required for Coaxitron control.
8 C1306M (8/05) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 1 OFF OFF OFF OFF OFF OFF OFF OFF 2 ON OFF OFF OFF OFF OFF OFF OFF 3 OFF ON OFF OFF OFF OFF OFF OFF 4 ON ON OFF O.
C1306M (8/05) 9 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 49 ON OFF OFF OFF ON ON OFF OFF 50 OFF ON OFF OFF ON ON OFF OFF 51 ON ON OFF OFF ON ON OFF OFF 52 OFF OFF ON OFF .
10 C1306M (8/05) T able B. D Protocol Receiver Address (Continued) ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 143 ON ON ON ON OFF OFF OFF ON 144 OFF OFF OFF OFF ON OFF OFF .
C1306M (8/05) 11 ADDRESS SWITCH SETTING SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 239 ON ON ON ON OFF ON ON ON 240 OFF OFF OFF OFF ON ON ON ON 241 ON OFF OFF OFF ON ON ON ON 242 OFF ON OFF OFF O.
12 C1306M (8/05) Install the Camera Module To install the camera module, do the following: 1. Refer to Figure 4. Loosen the set screw at the back of the camera enclosure with the provided 1.5 mm Allen wrench. Figure 4. Loosen Set Screw 2. Use the supplied spanner wrench to loosen the back of the camera enclosure (refer to Figure 5).
C1306M (8/05) 13 3. Slide the camera module into the camera enclosure. Refer to Figure 6 to position the camera module properly in the camera enclosure. Carefully mate the camera’ s power connector to the mating connector located inside the camera enclosure.
14 C1306M (8/05) 4. Models with a wiper: Refer to Figure 8 and do the following to install the arm of the wiper: a. Place the supplied green bushing on the stud located behind the handle of the camera module. The bushing should be in the same orientation as shown in Figure 8.
C1306M (8/05) 15 Install the Enclosure and Set Pan Position 1. Lightly apply O-ring lubricant (supplied) to the O-ring, and then install the O-ring on the rim of the power module (refer to Figure 9). Figure 9. Lightly Lubricate and Install O-Ring 2. Refer to Figure 10 and attach the enclosure unit to the power module.
16 C1306M (8/05) Set the T ilt Angle of the Camera Module 1. Place a 41 mm open end or crescent wrench on the tilt locking nut and a 21 mm open end wrench on the tilt shaft (refer to Figure 11). Figure 11. Set the T ilt Position 2. Hold the tilt shaft in position with the 21 mm wrench, and then turn the 41 mm wrench to loosen the tilt locking nut.
C1306M (8/05) 17 Install the Sun Shroud 1. Place the supplied nylon washers on the 6-32 Phillips pan head screws. Refer to Figure 12. 2. Align the mounting holes of the sun shroud with the holes on top of the camera enclosure. 3. Use the supplied nylon washers and screws to secure the sun shroud to the camera enclosure.
18 C1306M (8/05) Maintenance CAMERA MODULE REPLACEMENT To replace the camera module, do the following: 1. Remove the back cap of the camera enclosure. Refer to Figure 13 and do the following: a. Loosen the set screw with a 1.5 mm Allen wrench. b. Use the supplied spanner wrench to loosen the back cap of the camera enclosure.
C1306M (8/05) 19 3. Models with a wiper: Remove the wiper arm and the green bushing from the unit (refer to Figure 14). 4. Slide the camera module out of the enclosure. 5. Install the new camera module by doing the following: Slide the camera module into the camera enclosure.
20 C1306M (8/05) 6. Models with a wiper: Refer to Figure 14 and do the following to reinstall the arm of the wiper: a. Reinstall the green bushing on the stud located behind the handle of the camera module. b. Reinstall the wiper arm. Place the ridge of the arm in the notch of the camera enclosure tab and the slot of the arm over the green bushing.
C1306M (8/05) 21 Specifications ELECTRICAL Input V oltage 24 V AC or 100-240 VAC Input V oltage Range ±10% Power Consumption Maximum 60 watts (120 V A) per system Heater and Defroster Microprocessor.
22 C1306M (8/05) *Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770, CM9780, KBD200A, KBD300A, and MPT9500 controllers, but not with CM7500, MPT9000, or KBD9000 controllers.
PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FT/FR8000 Series fiber optic products.
W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .
Ein wichtiger Punkt beim Kauf des Geräts Pelco C1306M (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Pelco C1306M noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Pelco C1306M - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Pelco C1306M reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Pelco C1306M erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Pelco C1306M besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Pelco C1306M verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Pelco C1306M. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Pelco C1306M gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
