Benutzeranleitung / Produktwartung PT-LB75E des Produzenten Panasonic
Zur Seite of 55
E NGLISH Operating Instructions LCD Projector Model No. PT-LB80NTE PT-LB80E PT-LB75NTE PT-LB75E Before operating this product, please read th e instruct ions carefully and sa ve th is manual for future use.
Important Information E NGLISH - 2 Important Safety Notice Dear Panasonic Customer: This instruction booklet provides all th e nec essary operating inform ation that you might requ ire. We hope it will help you to get the most out of your new product, and that you will be pleased with your Panasonic LCD projector.
Important Information Important Safety Notice E NGLISH - 3 Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and /or accompanying docu ments means that used electrica l and electronic prod ucts should not be mixed with general househ old waste.
Important Information Important Safety Information E NGLISH - 4 Declaration of Conformity Declaration of Conformity (DoC) This equipment is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Important Safety Information E NGLISH - 5 Important Infomation.
E NGLISH - 6 Contents J Quick steps Important Safety Notice ...... .......... ............ ................. 2 Declaration of Conformity...................... .............. ........... ... 4 Precautions with regard to safety ............ ............
Preparation Getting Started Basic Operation Settings Maintenance Appendix E NGLISH - 7 Contents Important Infomation Menu Navigation .................... ................ ................. ..29 Navigating th rough the MENU . ..........................
Important Information E NGLISH - 8 Precautions with regard to safety If you notice smoke, stra nge smells or noise co ming from the projector, disconnect t he mains plug from the mains socket. Do not continue to use the projector in such cases, otherwise fire or electric shocks could res ult.
Precautions with regard to safety E NGLISH - 9 Important Information Do not place your skin into the light beam wh ile the projector is being used. S trong light is emitted from the projector’s lens. If you place directly into this lig ht, it can hurt or damage your skin.
Precautions with regard to safety E NGLISH - 10 Important Information Do not short-circuit, heat or disassemble the batteries or pl ace them into water or fire. Failure to obser ve this ma y cause the batteries to overheat, leak, explode or catch fire, and burns or other injury may result.
Precautions with regard to safety E NGLISH - 11 Important Information Avoid setting up in places which are subject to vibration or shocks. The internal p arts ca n be damaged, which may cause malfunctions or accident s.
Precautions with regard to safety E NGLISH - 12 Important Information Make sure the following accessories are provided with yo ur projector. * The protectors for en clos ed prod ucts, such a s a plug cover or foam cartons, must be treated prop erly. * Contact to an Authorised Service Centre for lost access ories.
E NGLISH - 13 Preparation Read this first When you start the projection for the first time or after the projector is initialis ed, the minimum required settin g screen for projection will be displayed. J LANGUAGE Select the required lang uage setting.
E NGLISH - 14 Preparation About Your Projector J T op and front view Projector body NOTE: • Do not cover the ventilation openings or p lace anything within 50 cm ( 20") of them as this may cause damage or injury . • While the pr ojector is not i n use, keep the lens cover attached to protect the lens.
Preparation About Your Projector E NGLISH - 15 J Back and bottom view NOTE: • Do not cover the ventilation openings or place anything within 50 cm (20") of them as this may cause damage or injury . • When a cable is connected to the VARIABLE AUDIO OUT , the built-in speaker will be disa bled.
Preparation About Your Projector E NGLISH - 16 Battery compartment 1. Press the tab and lift up the cover . 2. Insert the batteries according to the polarity diagram indicated inside. T op view (page 25) Att aching a hand strap You can attach a favourite strap on to the remote control .
Getting Started E NGLISH - 17 Setting up You can adjust the projection size with 2.0x zoom l ens. Calculate and define the th row distance as follows. * All measurements ab ove are appro ximate and may di ffer slightly from the actual measurements.
Getting Started Setting up E NGLISH - 18 You can use the projec tor with any of the follo wing 4 projecti on methods. T o set the desired meth od in the projec tor, See “INSTALL ATION” on page 37. Y ou can adjust the projection angle in the vertic al direction by pressing the leg adjuster buttons.
Getting Started E NGLISH - 19 Connections Read and follow the operating and con necting in structions o f each peripher al device. The peripher al devices must be turned off. Prepar e the connecting cab les that match wit h the projector and peripheral device terminals.
E NGLISH - 20 Basic Operation Switching the projector on/off J Connecting 1. Make sure the sh ape of the mains plu g and the AC IN terminal on the ba ck of the proj ector match, then push th e plug all th e way in. 2. Align the side of the powe r cord secure lock wi th the side guide rail of the AC IN terminal of the projector and slide it in.
Basic Operation Switching the projector on /off E NGLISH - 21 Before switching on the projector, make sure the mains lead and all the other devices are connected correctly . See “Connections” on page 19 a nd “Mains lead” on page 20 . Q By control p anel operation Make sure CONTRO L PANEL in OPTION menu is set to VALID .
Basic Operation Switching the projector on/off E NGLISH - 22 J By control p anel operation Make sure the CONTROL PANEL setting in OPTION menu is set to VALID .
Basic Operation Switching the projector on /off E NGLISH - 23 The POWER indicator in forms you the status of th e power and th e POWER LOCK indicator sh ows the status of the RELEASE button.
E NGLISH - 24 Basic Operation Projecting an image 1. Switch on the connecte d devices. Press the play button of the required device. 2. Detect the input signal automatically . 3. Switch the aspect ra tio automatically . 1. Place the projector at th e right angle from the screen.
E NGLISH - 25 Basic Operation Remote control operation You can operate the pr ojector with the remote control within the remote range 15 m (4 9'2"), approximately ± 30° vertically and horizontally .
Basic Operation Remote control operation E NGLISH - 26 You can switch the input meth od manually by pressing the COMPUTER , WIRELESS (PT-LB80NTE/PT-LB75NTE only) and VIDEO buttons. Press the require d button several times or I H to cycle through the input methods as follows.
Basic Operation Remote control operation E NGLISH - 27 You can project an image split in 2 windows as an INDEX-WINDOW . One is froze n and stored in memory, and displa yed on the screen’s left side while di splaying subsequent image continues on the right.
Basic Operation Remote control operation E NGLISH - 28 You can enlarge the pr ojected image down to a centred area for emph asizing within th e range of 1x to 2x. Q Enlarging the image 1. Press any side of the DIGITAL ZOOM +/- button once. The centred area of the im age will then be enlarged 2.
E NGLISH - 29 Settings Menu Navigation The menu system allows you to access fu nctions which do not have their own dedicated buttons on the remote control. The menu options are str uctured and cate gorised. You can n avigate through the menu with FGHI buttons.
Settings Menu Navigation E NGLISH - 30 The main menu has 6 o ptions. Select the requ ired menu item and press ENTER to display the sub-menu. Underlined items are factory default settings. PICTURE POSITION LANGUAGE Main menu and Sub-menu NOTE: • Some default settings vary by the selected in put signal.
Menu Navigation E NGLISH - 31 Settings OPTION SECURITY WIRELESS (PT-L B80NTE/P T-LB75NTE only) INPUT GUIDE page 36 DETAILED SIMPLE OFF STARTUP LOGO page 36 ON OFF USER COMPUTER2 SELECT page 36 INPUT O.
E NGLISH - 32 Settings PICTURE menu Depending on the projection environment, you can use these pres et parame ter settings to optimis e image projection. Press I H to cycle through the op tions. You can adjust the contrast of the projected image. Adjust the BRIGHTNESS in advance if necessary.
PICTURE menu E NGLISH - 33 Settings You can perform more detailed imag e adjustment manually. J For S-VIDEO/VIDEO signals Q TV-SYSTEM When the video signal is changed, the se tting switches automatically . Y ou can switch the setting manually to match the video dat a.
E NGLISH - 34 Settings POSITION menu If the projector is aligned no n-perpendi cularly to the screen, or if the projection screen has an angled surface, the keystone will be corrected automatically.
POSITION menu E NGLISH - 35 Settings Q 16:9 The squeezed signal will be projected in 16:9 ratio. Q S4:3 The input signal will be sized down 75 % and projected. S4:3 mode is ef fective when projecting 4:3 image on to a 16:9 screen. Q THROUGH The image will be projected without any s ize adjustment .
E NGLISH - 36 Settings OPTION menu When you change the input method, th e guidance appears in the upper right co rner of the screen. The following display methods are availa ble. Press I H to cycle through the options. You can switch the logo on/off that is displayed when starting up the projector.
OPTION menu E NGLISH - 37 Settings You can adjust the power of the lamp to save electricity, prolong the lamp life and reduce the noise. STANDARD When higher luminance is required ECO-MODE When lower luminan ce is sufficient You can check how long the lamp has been u sed.
Settings OPTION menu E NGLISH - 38 You can select a useful function fr om the list and assign to the FUNCTION button for shortc ut. 1. Press the ENTER button. 2. Press FG to select the required function. 3. Press the ENTER button. The dot on the left of the option is indicating the assigned function.
E NGLISH - 39 Settings SECURITY menu J Entering the SECURITY menu Every time w hen you ap ply to the SECURITY menu, you will be asked to per form the passwor d operation. When you apply to the SECURITY menu before you change the password to your origina l, perform to input the following factory default pa ssword operation.
E NGLISH - 40 Settings WIRELESS menu In WIRELESS menu , the following items are av ailable. NETWORK NAME CHANGE INPUT PASSWORD PASSWORD CHANGE NETWORK STANDBY WEB CONTROL LIVE MODE CUT IN STATUS INITIALI ZE NOTE: • The WIRELESS menu is available only with PT-LB8 0NTE/P T-LB75NTE.
E NGLISH - 41 Maintenance LAMP and TEMP Indicators If a problem should occu r with the projector, the LAMP and/or TEMP indicators will inform you. Manag e the indicated pr oblems as follow. 1. Confirm the st atus of all indicators and projector , and switch off the projector in proper way .
E NGLISH - 42 Maintenance Care and Replacement J Before cleaning the projector Switch of f the projector and disconnect the mains plug from the mains socket. Unplug all the cables from the projector . J Cleaning the outer surf ace of the projector Wipe off dirt and du st gently with a sof t cloth.
Care and Replacement E NGLISH - 43 Maintenance The lamp un it, ET-LAB80 is consumab le and you mu st repl ace it regularly. It is recommended that a qualified technician carry the lamp un it replacement and consult with an Autho rised Service Centre.
Maintenance Care and Replacement E NGLISH - 44 J Replacement proce dure Q Removing and replacing the lamp unit 1. Use a Phillips-head screwdriver to loosen the 2 lamp unit cover fixing screws on the back of the projector until the screws turn freely , and remove the lamp unit cover .
E NGLISH - 45 Maintenance Troubleshooting Should any problem persist, contact yo ur dealer. Problem Cause Reference pag e Power does not turn on. The mains lead may not be connected securely . No electric supply at the mains socket. TEMP indicator is lit or flashes.
E NGLISH - 46 Appendix Technical Information List of comp atible signals Mode Display resolution (dot s) *1 *1. The “i” appearing after the resolu tion indicates an interlaced signal. Scanning frequency Dot clock frequency (MHz) Picture quality *2 *2.
Technical Information E NGLISH - 47 Appendix The serial connector wh ich is on the con nector panel of the pr ojector conforms to the RS-232C interface specificatio n, so that the proje ctor can be contr olled by a personal computer which is connected to th is connecter.
Appendix Technical Information E NGLISH - 48 J Cable specifications (When connected to a personal computer) J Control commands You can switch the signals which to output fro m the COMPUTER1 OUT terminal by pressing the computer key command. The ke y commands are depe nd on the ma nufactures.
Technical Information E NGLISH - 49 Appendix * All measurements ab ove are appro ximate and may di ffer slightly from the actual measurements. J Calculation methods for screen dimensions Y ou can calculate more detaile d screen dimension from the scr een diagonal.
Appendix Technical Information E NGLISH - 50 S pecifications Power supply AC 100 - 240 V 50 Hz/60 Hz Power consumption 300 W During standby (when fan is stopped): 4 W Amp s 3.
Technical Information E NGLISH - 51 Appendix T erminals S-VIDEO IN Single - line, Mini DIN 4p Y: 1.0 V [p-p], C: 0.286 V [p-p], 75 Ω VIDEO IN Single - line, RCA pin jack 1.0 V [p-p], 75 Ω COMPUTER Single - line, D - sub HD 15-pin (female) RGB input/output R.
Appendix Technical Information E NGLISH - 52 VGA and XGA are trademarks of In ternat ional Business Machines Co rporation. S-VGA is a registered tradema rk of the Video Electronics S tandards Association. HDMI, the HDMI logo and Hig h-Definition Multimedia Interface are trad emarks or registered tr ademarks of HDMI Licensing LLC.
E NGLISH - 53 Appendix Index A AC IN .............. ................................. .......... 15 Accessories ................. .............. ........... ........ 12 Air exhaust port ................ ................. ............ 15 Air filter Cleaning .
Appendix Index E NGLISH - 54 N Navigation buttons Control panel button ............. .............. ........... 14 Remote control button ........... .............. ........... 16 NOISE REDUCTION .............. .............. ........... 33 O OPTION menu .
Matsushita Electric Industrial Co., Ltd. Web Site: http://panasonic.net © 2008 Matsushita Electric Industrial Co., Ltd. All Rights Reserved. Printed in Japan S0308-1048B.
Ein wichtiger Punkt beim Kauf des Geräts Panasonic PT-LB75E (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Panasonic PT-LB75E noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Panasonic PT-LB75E - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Panasonic PT-LB75E reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Panasonic PT-LB75E erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Panasonic PT-LB75E besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Panasonic PT-LB75E verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Panasonic PT-LB75E. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Panasonic PT-LB75E gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
