Benutzeranleitung / Produktwartung PT-DW7000E des Produzenten Panasonic
Zur Seite of 106
DLP TM Based Projector Commercial Use Operating Instructions Read these instructions completely before operating this unit. TQBJ 0147-3 POWER ON OFF RGB 1 RGB 2 AUX MENU STD LENS OSD 1 4 7 2 5 8 3 6 9 0 NEXT USER LIGHT ID ALL ASPECT ID SET Projector Computer Numetric BRIGHT CONTRAST ON SCREEN SYSTEM SEL FUNC 1 D.
2 Dear Panasonic Customer: This instruction booklet provides all the necessary operating information that you might require. We hope it will help you to get the most performance out of your new product, and that you will be pleased with your Panasonic DLP TM based projector.
3 ENGLISH IMPORT ANT : THE MOULDED PLUG (U.K. only) FOR YOUR SAFETY , PLEASE READ THE FOLLOWING TEXT CAREFULL Y . This appliance is supplied with a moulded three pin mains plug for your safety and convenience.
4 Adjusting the position .............................................51 Shift adjustment ...............................................................51 Size adjustment ...............................................................52 Clock phase adjustment .
5 ENGLISH Precautions with regard to safety W ARNING If a problem occurs (such as no image) or if you notice smoke or a strange smell coming from the projector , turn off the power and disconnect the power cord from the wall outlet. • Do not continue to use the projector in such cases, otherwise fire or electric shocks could result.
6 Precautions with regard to safety Do not place liquid containers on top of the projector . • If water spills onto the projector or gets inside it, fire or electric shocks could result. • If any water gets inside the projector, contact an Authorized Service Centre.
7 ENGLISH Accessories Check that all of the accessories shown below have been included with your projector. Do not look into the lens while the projector is being used. • Strong light is emitted from the projector’s lens. If you look directly into this light, it can hurt and damage your eyes.
8 Precautions on handling Precautions on transport The projection lens is susceptible to vibrations and impacts. Be sure to always remove the lens during transport. Precautions on installation Be sure to observe the following precautions when installing the product.
ENGLISH 9 The projector is provided with a number of terminals and optional accessories to enable various system expansions. Both input and output are provided to all terminals on the main unit.
10 Name and function of parts < When the operation mode selector is set to Projector > Remote control operation indicator lamp The lamp flashes when any remote control button is pressed. POWER ON button (page 33) Turns on the power if the MAIN POWER has been put to the “ l ” position.
11 ENGLISH LIGHT button ( Click button) When this button is pressed, the remote control button light is turned on.The light goes off about 30 seconds after you stop remote control operation. USER button Displays the sub-memory screen of the signal registration.
12 Side-mounted connection terminals (page 14) AC IN terminal (page 33) Connect the supplied line power cord into this receptacle. Do not connect any other cable to this socket. MAIN POWER switch (page 33) Use this switch to turn on “ I ” and off “ o ” the commercial line power applied to the projector.
13 ENGLISH Lamp unit cover The lamp unit is housed. Remote control receiver window (rear) (page 15) This also receives the signal beam coming from the remote control. POWER ON (I) button (page 33) Turns on the power. POWER OFF ( ) button (page 34) Turns off the power.
14 S-VIDEO IN terminal (pages 22 and 23) An input terminal for S-video signals (MIN4-pin DIN). This terminal complies with S1 signals and automatically toggles between 16:9 and 4:3 according to the size of input signals. VIDEO IN terminal (page 23) An input terminal for video signals.
ENGLISH 15 Loading dry cells When loading supplied AA dry cells into the battery compartment of the remote control, make sure that their polarities are correct. 1. Open battery compartment lid. Open the lid in the order of steps and . 2. Insert the dry cells.
16 Every projector has its ID number and the ID number of the controlling projector must be set to the remote control in advance so that the user can operate the remote control. The ID number of the projector is set to “ ALL ” on shipping, and use the ID ALL button of the remote control when using only a single projector.
17 ENGLISH Using the remote control as a PC mouse Operation mode selector switch Put the knob to the Computer position. • ENTER button Pressing the front, rear, left and right edges of the button moves the mouse cursor up, down, left and right. • Right click ( ) button This button can be used as the right mouse button.
18 Projection scheme This projector can use any of the four projection schemes shown at right. Select the scheme that best suits your particular installation location. Select the most suitable scheme to the situation of your location. Use the OPTION menu on the menu screen to choose the desired projection scheme.
ENGLISH 19 L : Projection distance SH : Effective screen height Projection distances by the type of projection lenses (for PT -D7700E) • For the screen aspect ratio of 4:3 Units: m • The projection distances listed here involve an error of ± 5%.
20 • The projection distances listed here involve an error of ± 5%. • Keystone distortions are corrected in the way the screen size becomes smaller than the original one.
21 ENGLISH If the projector is used with a screen size not listed in this manual, check the diagonal dimension (inch) of your screen and calculate the projection distance using the following formulas. Calculation formulas for projection distance by lens types (for PT -D7700E) Minimal distance: L=0.
22 Connection Before connection, read carefully the instruction manual for the device to be connected. Turning off the power switch of the devices before connecting cables.
23 ENGLISH SERIAL S-VIDEO VIDEO REMOTE 1 RGB 1 IN IN IN IN OUT OUT OUT SYNC/HD VD B/P B G/Y REMOTE 2 R/P R RS-232C (G) / RS-422 (R) RS-232C (G) / RS-422 (R) IN RGB 2 IN Video deck (TBC built-in) High-.
24 SERIAL S-VIDEO VIDEO REMOTE 1 RGB 1 IN IN IN IN OUT OUT OUT SYNC/HD VD B/P B G/Y REMOTE 2 R/P R RS-232C (G) / RS-422 (R) RS-232C (G) / RS-422 (R) IN SERIAL S-VIDEO VIDEO REMOTE 1 RGB 1 IN IN IN IN .
25 ENGLISH SERIAL S-VIDEO VIDEO REMOTE 1 RGB 1 IN IN IN IN OUT OUT OUT SYNC/HD VD B/P B G/Y REMOTE 2 R/P R RS-232C (G) / RS-422 (R) RS-232C (G) / RS-422 (R) IN SERIAL S-VIDEO VIDEO REMOTE 1 RGB 1 IN I.
26 SMPTE259M compliant : 480i, 576i 10BASE-T/100BASE-TX SMPTE259M compliant : 480i, 576i SMPTE292M compliant : 720/60p, 720/59.94p, 720/50p 1 035/60i, 1 035/59.94i, 1 080/60i, 1 080/59.94i 1 080/50i, 1 080/24sF, 1 080/23.98sF, 1 080/30p 1 080/29.97p, 1 080/25p, 1 080/24p, 1 080/23.
27 ENGLISH Procedure of installation Disconnect the power before installing the input module. Slot cover Remove 2 screws. Input module Slot Tighten the two screws. Remove the slot cover . Insert the input module. Fix the input module. Register the input signal.
28 SD-SDI input module ET-MD77SD1 DVI-D input module ET-MD77DV Network module ET-MD77NT SDI signal DVI signal LAN 10BASE-T/ 100BASE-TX Projector High-vision video deck DVD player Business digital VCR .
29 ENGLISH SD-SDI Module ET-MD77SD1 IN SERIAL OUT LAN SD-SDI signal SD-SDI signal output (active through) LAN terminal (10BASE-T / 100BASE-TX) Business digital VCR For details on the network function, refer to page 82. SD-SDI input module (optional) ET-MD77SD1 (for 480i/576i) • Insert the input module suitable for the input signal specifications.
30 Installation of input module (optional) • Insert the input module that meets the input signal specifications. • Normally, use SYSTEM SELECTOR in “ AUTO ” .
31 ENGLISH DVI-D input module (optional) ET-MD77DV DVI Module ET-MD77DV DVI-D IN LAN DVI-D signal DVD player or high-vision video deck equipped with DVD/HDMI terminal PC with DVI output LAN terminal (10BASE-T / 100BASE-TX) For details on the network function, refer to page 82.
32 How to install and remove the projection lens (optional) How to install the projection lens While pressing the lock button on the projection lens cover , pull the cover forward to remove it. Pull and remove the dustproof sheet on the back of the projection lens cover .
ENGLISH 33 Powering up the projector Connect the supplied power cable. (220 V – 240 V~, 50 Hz/60 Hz) Press the “ I ” marked side of the MAIN POWER switch to turn on the power . The power indicator lamp on the projector will flash in red. After a short period, the indicator will illuminate and the projector will enter standby mode.
34 Powering off the projector Press the POWER OFF “” button. Select “ OK ” with or button and press the ENTER button. (or press the POWER OFF “” button again.) The projection of the image stops, and the power indicator lamp of the main unit lights up orange.
ENGLISH 35 If the focusing, zooming or positioning of the image projected on the screen is not successful, even though the projector is properly positioned against the screen, you can adjust the focus, the zoom, or the vertical or horizontal position of the image.
36 How to adjust the lens If the image is out of focus in any portion of the screen, adjust the lens by turning the adjustment screws to obtain evenness of focusing. How to adjust the lens for addressing unevenness of focusing Remove the lens cover and lens (Refer to page 32).
ENGLISH 37 Automatic adjustment (AUT O SETUP) Automatic adjustment function adjust the resolution, clock phase and image position automatically when dots- structured analogue RGB signals such as computer signal are supplied. (Automatic adjustment is not available if signals or moving images other than analogue RGB signals are supplied.
38 Registration of input signal data • The data of 96 input signals can be registered. • The signals supporting the installed input module are input and their data registered. • The memories are numbered over 12 pages (A to L: 8 data items can be registered on each page), and the data is registered in the unused memory with the lowest number.
39 ENGLISH Clearing the data of registered signals Press the “ MENU ” button. The MAIN MENU screen will be displayed. Select “ SIGNAL LIST ” with the and buttons. Press the “ ENTER ” button. The REGISTERED SIGNAL LIST screen will be displayed.
40 Registration of input signal data Sub memory The projector is provided with a sub memory function to register plural pieces of image adjustment data even they are determined to be the same signal by the frequency and form of the synchronization signal source.
41 ENGLISH On-screen indications Input switching / signal switching This shows the registered signal name on the status screen for signal switching. The designation can be set by the sub memory items. The place in which address code (A1, A2, ..., H7 and H8) signals are registered displays the sub memory number.
42 Using the FREEZE function Pressing the “ FREEZE ” button of the remote control switches between a still image and a motion image. If the projector is not used for a certain period of time during the meeting intermission, for example, a shutter mode is available that allows the user to hide images temporarily.
ENGLISH 43 Structure of menu screens Menus are extensively used for configuring, adjusting or reconfiguring the projector. The menus structure is as follows: MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY :MENU SELECT ENTER:SUB MENU PICTURE PICTURE MODE DYNAMIC COLOR 50 TINT 30 COLOR TEMP.
44 On-screen menus Basic operations on menu screen Press the “ MENU ” button. The MAIN MENU appears on the screen. Select the desired item with the or button. Selected items are displayed in blue. Press the “ ENTER ” button to establish your selection.
ENGLISH 45 Adjusting the picture Switching the picture mode The user can switch to the desired picture mode suitable for the image source and the environment in which this projector is used. PICTURE PICTURE MODE DYNAMIC COLOR 50 TINT 30 COLOR TEMP. DEFAULT GAMMA 2.
46 Adjusting the picture The desired picture can be obtained by following the procedure below. Adjusting Contrast / Bright / Colour / T int Adjustment procedure – to adjust picture (colour intensity) PICTURE PICTURE MODE DYNAMIC COLOR 50 TINT 30 COLOR TEMP.
47 ENGLISH PICTURE PICTURE MODE DYNAMIC COLOR 50 TINT 30 COLOR TEMP. DEFAULT GAMMA 2.2 CONTRAST 32 BRIGHT 32 SHARPNESS 6 NOISE REDUCTION 2 DYNAMIC IRIS 1 MAIN MENU PICTURE POSITION ADVANCED MENU LANGU.
48 Adjusting the picture DYNAMIC IRIS AUTO IRIS 2 MANUAL IRIS OFF DYNAMIC GAMMA 1 :MENU SELECT :CHANGE 2 3 1 DYNAMIC IRIS USER OFF DYNAMIC IRIS setting Pictures with the optimum contrast will be displayed by automatically providing aperture compensation and signal compensation to suit the pictures concerned.
49 ENGLISH PICTURE PICTURE MODE DYNAMIC COLOR 50 TINT 30 COLOR TEMP. DEFAULT GAMMA 2.2 CONTRAST 32 BRIGHT 32 SHARPNESS 6 NOISE REDUCTION 2 DYNAMIC IRIS 1 :MENU SELECT :CHANGE Press the “ MENU ” button. The MAIN MENU screen will be displayed Select “ PICTURE ” with the buttons.
50 Adjusting the picture Press the “ MENU ” button. The MAIN MENU screen will be displayed. Select “ PICTURE ” with the buttons. Press the “ ENTER ” button. The PICTURE screen will be displayed. Select desired one of the items in the following table with the buttons.
51 Adjusting the position ENGLISH Desired position can be achieved by following the procedure below. Shift adjustment This function allows the user to adjust the picture position vertically or horizontally if the position of the image projected on the screen is displaced when the projector is properly positioned against the screen.
52 Adjusting the position POSITION SHIFT SIZE DEFAULT CLOCK PHASE 0 KEYSTONE :MENU SELECT :CHANGE ENTER:SUB MENU Press the “ MENU ” button. The MAIN MENU screen will be displayed.
53 ENGLISH Some size modes are not available for certain types of input signals. • For RGB1 and RGB2 input signals: VID AUTO, S1 AUTO or VID AUTO ( PRIORITY) cannot be selected. • For VIDEO input signals: DEFAULT, S1 AUTO or VID AUTO (PRIORITY) cannot be selected.
54 Adjusting the position POSITION SHIFT SIZE DEFAULT CLOCK PHASE 0 KEYSTONE :MENU SELECT ENTER:SUB MENU MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY :MEN.
55 How to use ADV ANCED MENU ENGLISH • In DIGITAL CINEMA REALITY mode, the image quality will be deteriorated if 30p FIXED or 25p FIXED is selected when the signal is not a 2:2 pulldown signal. Note ADVANCED MENU DIGITAL CINEMA REALITY AUTO FORMAT SMPTE BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING OFF SYNC.
56 How to use ADV ANCED MENU ADVANCED MENU DIGITAL CINEMA REALITY AUTO FORMAT SMPTE BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING OFF SYNC.TERM 75 RASTER POSITION :MENU SELECT ENTER:SUB MENU Press the “ MENU ” button. The MAIN MENU screen will be displayed.
57 ENGLISH ADVANCED MENU DIGITAL CINEMA REALITY AUTO FORMAT SMPTE BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING OFF SYNC.TERM 75 RASTER POSITION :MENU SELECT ENTER:SUB MENU MAIN MENU PICTURE .
58 How to use ADV ANCED MENU ADVANCED MENU DIGITAL CINEMA REALITY AUTO FORMAT SMPTE BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING OFF SYNC.TERM 75 RASTER POSITION :MENU SELECT ENTER:SUB MENU .
59 ENGLISH ADVANCED MENU DIGITAL CINEMA REALITY AUTO FORMAT SMPTE BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING ON SYNC.TERM 75 RASTER POSITION :MENU SELECT :CHANGE ENTER:SUB MENU MAIN MENU P.
60 How to use ADV ANCED MENU BRIGHT ADJUST BRIGHT INSIDE 6 BRIGHT OUTSIDE 6 UPPER 0 LOWER 0 LEFT 0 RIGHT 0 Projection range Edge blending width (right) BRIGHT adjustment (right) Marker BRIGHT INSIDE BRIGHT OUTSIDE Select the “BRIGHT ADJUST” with the buttons.
61 ENGLISH ADVANCED MENU DIGITAL CINEMA REALITY AUTO FORMAT SMPTE BLANKING INPUT RESOLUTION CLAMP POSITION EDGE BLENDING OFF SYNC.TERM 75 RASTER POSITION RASTER POSITION V: 0 H: 0 MAIN MENU PICTURE PO.
62 Changing the display language • The on-screen display of the projector is set to the English language on shipping. Note Press the “ MENU ” button.
ENGLISH 63 How to change the system format Pressing the SYSTEM SELECTOR button on the remote control or using the menu screen operation (page 81) enables the user to make the following changes depending on S Video / Video input or the currently selected input module.
64 Option settings OPTION PROJECTOR ID 2 SETTING FRONT-F LAMP SELECT DUAL LAMP POWER HIGH RS232C SETTING OSD POSITION 2 SYSTEM INFORMATION COLOR MATCHING OFF VIDEO SETTING AUTO SETUP :MENU SELECT :CHA.
65 ENGLISH A: Floor mount front projection (Front – Floor mount) D: Ceiling mount rear projection (Rear – Ceiling mount) C: Floor mount rear projection (Rear – Floor mount) B: Ceiling mount fron.
66 Option settings Lamp select Two internal lamps in the projector can be used either in “ DUAL ” or “ SINGLE ” mode depending on user's needs or viewing conditions. In the “ SINGLE ” mode, the projector may automatically switches between one lamp and the other, or one of the lamps can be specified.
67 ENGLISH Position of on-screen indications The user can specify the position of the on-screen indications “ 1 ” : Top left of the screen “ 2 ” : Left centre of the screen “ 3 ” : Bottom .
68 Option settings Adjusting colour matching When multiple sets are used simultaneously, this projector allows the user to correct the difference of colours among the sets.
69 ENGLISH MEASURE MODE MEASURED DATA TARGET DATA AUTO TESTPATTERN ON :MENU SELECT ENTER:SUB MENU MEASURE MODE MEASURED DATA TARGET DATA AUTO TESTPATTERN ON MEASURE MODE MEASURED DATA TARGET DATA AUTO TESTPATTERN ON TARGET DATA R, G, B Cy, Mg, Ye, Wh TARGET DATA: R, G ,B R x 0.
70 Automatic adjustment (Only for RGB input) Use this setting when adjusting a specific or oblong (16:9, etc.) signal. Press the MENU button. The MAIN MENU screen will be displayed. Select “ OPTION ” with the buttons. Press the ENTER button. The OPTION screen will be displayed.
71 ENGLISH Fan control When using the projector over 1 400 m above sea level, set to “ HIGHLAND ” . FAN CONTROL NORMAL HIGHLAND OPTION OUTPUT RESOLUTION SXGA+ AUTO SIGNAL ON FAN CONTROL NORMAL P I.
72 Option settings P IN P This item is used to set the condition of the Picture-In- Picture. Main window Subwindow Use the buttons to select "OFF", "USER 1", "USER 2", or "USER 3". When selecting an option other than "OFF", the submenu can be displayed by pressing the ENTER button.
ENGLISH 73 Setting FUNC1 The user can specify the function of the “ FUNC 1 ” button on the remote control. “ P IN P ” : Enables setting of P IN P to OFF, USER 1, USER 2, or USER 3. (refer to page 72). “ LAMP POWER ” : Enables the lamp power to be switched between high and low (refer to page 66).
74 Pin assignments and signal names The main unit is equipped with SERIAL terminals located in its terminal section on the side, and this terminal is compliant with RS-232C. Also a serial output terminal is provided to enable plural projector control.
75 ENGLISH Control commands When controlling the projector from a computer, the following commands are available: Cable specifications • To connect the computer to the SERIAL terminal, prepare an adequate communication cable that fits to your personal computer.
76 Using the REMOTE 2 terminal provided on the side of the main unit, it is possible to operate the projector from a control panel etc. furnished in a distant location where infrared remote control signal cannot be received. Pin assignments and control Be sure to short-circuit Pins and when controlling.
ENGLISH 77 Displaying the internal test pattern The projector has eight types of internal test patterns to check the condition of the set. To display test patterns, follow the steps below. • Results of adjustment on the image, picture quality, position, size and other factors will not be reflected in test patterns.
78 Setting the security MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY :MENU SELECT ENTER:SUB MENU PASSWORD :INPUT ENTER:SET SECURITY PASSWORD OFF PASSWORD .
79 ENGLISH SECURITY PASSWORD OFF PASSWORD CHANGE TEXT DISPLAY OFF TEXT CHANGE SECURITY PASSWORD OFF PASSWORD CHANGE TEXT DISPLAY OFF TEXT CHANGE SECURITY PASSWORD OFF PASSWORD CHANGE TEXT DISPLAY OFF TEXT CHANGE TEXT PASSWORD NEW CONFIRM :INPUT ENTER:SET Select “ TEXT DISPLA Y ” with the buttons.
80 How to use CP OPTION MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY CP OPTION :MENU SELECT ENTER:SUB MENU CP OPTION OSD ON SYSTEM SELECTOR :MENU SELECT :.
81 ENGLISH MAIN MENU PICTURE POSITION ADVANCED MENU LANGUAGE OPTION TEST PATTERN SIGNAL LIST SECURITY CP OPTION :MENU SELECT ENTER:SUB MENU CP OPTION OSD ON SYSTEM SELECTOR :MENU SELECT :CHANGE SYSTEM.
82 The input module (ET-MD77NT, ET-MD77DV, ET-MD77SD1 or ET-MD77SD3) available as an optional accessory comes with a network function to enable the projector to be controlled from the Web browser of the personal computer. In addition, the network function also fulfills automatic E-mail transmission function.
83 ENGLISH Press the “ ENTER ” button. The OPTION screen will be displayed. Select “ NETWORK SETTING ” with the buttons. Initial setting of network function Procedure of setting Press the “ MENU ” button. The MAIN MENU screen will be displayed.
84 How to use network function (optional) Items Function Description HOSTNAME DHCP IP ADDR PORT No. NET MASK GATEWAY MAC ADDR Make alteration if necessary when to use the DHCP server. Set the DHCP item to ON when to acquire an IP address automatically using the DHCP server.
85 ENGLISH • Avoid activating two or more Web browser simultaneously to work out setting or control actions. • Change the password first of all. Note Accessing from the W eb browser Activate the Web browser in the personal computer . Enter the IP address set by the projector into the URL input field of the Web browser .
86 How to use network function (optional) Basic control page This page is the first page displayed when the projector is accessed through a web browser. To move from another page, click [Projector control], then [Basic control]. Control button Click this item, and a projector control page appears.
87 ENGLISH (Continued on next page) Detail control page Click [Projector control], then [Detail control] to display the Detail control page. On-screen status is displayed, even if the on-screen of projector is set to off.
88 How to use network function (optional) When is displayed on the status information screen, click it to display the error details. Error information page OK: Normal operation FAILED: Occurrence of t.
Select “ Enable ” to use the E- mail function. 89 ENGLISH E-mail setup page With this projector, if a problem occurs or if the lamp usage time reaches a set value, an e-mail message can be sent to one or more preset e-mail addresses (maximum two addresses).
90 How to use network function (optional) Enter the E-mail address to which the E-mail is to be sent when two E-mail addresses are going to be used. Do not enter it when the second E- mail address is not going to be used. Select the conditions for sending E-mail.
91 ENGLISH POP server setup page The POP server is set on this page when POP authentication is required for mail transmissions. Click [Network set up], then [POP server set up] to display the POP server setup page. Select “ Enable ” for this setting only when authentication is required for sending mail.
92 Subject: Panasonic projector report(CONFIGURE) === Panasonic projector report(CONFIGURE) === Projector Type : D7700 ––––– E-mail setup data ––––– TEMPERATURE WARNING SETUP MINIM.
93 ENGLISH Adjust clock page Click [Network set up], then [Adjust clock] to display the Adjust clock page. Time zone selection Button to update time zone setting Button to update time and date settings New date field New time field Network config page Set this to ON to enable the DHCP client function.
94 Firmware update page (The firmware should be updated only by an individual with the specialized knowledge required to do this.) Enter here the filename of the firmware to be updated. After entering the filename, press the [Upload] button. Data transfer is now commenced.
95 ENGLISH Press the “ ENTER ” button. The OPTION screen will be displayed. Select “ NETWORK SETTING ” with the buttons. Returning the network function setting back to the factory setting Using the following procedure, the user can return all settings of network function such as IP address, password and Email setting to the factory setting.
96 Indication of monitor lamp Three monitor lamps are provided at the top of main unit front to inform the user of the lamp replacement time and unusual internal temperature. These lamps indicate the degree of abnormality by combination of blinking and/or lighting lamps.
97 Cleaning and replacement of air filter ENGLISH T urn off the main power and remove the power plug from the receptacle. Turn off the power supply observing the procedure (How to turn “ OFF ” the power supply) on page 34 and then remove the power plug.
98 Replacement of lamp unit Precautions on lamp unit replacement Be careful when handling a light source lamp. The lamp unit has high internal pressure. If improperly handled, failure might result. A used lamp unit may burst if it is handled violently.
99 ENGLISH • After 1 500 hours (4 000 hours when Long Life Lamp Units are used) of operating the same lamp, it is only possible to operate the unit for approximately 10 minutes.
100 8. Insert the power cord plug into the wall outlet and then press the MAIN POWER switch. • If the power does not turn on (power indicator lamp (red) does not turn on) even after turning the MAIN POWER switch “ I ” , turn the MAIN POWER “ O ” , confirm that the lamp unit and door are installed correctly, and turn on again.
101 Before asking for service … try to check the following points again. ENGLISH Symptoms Checkpoint • Is the power cord securely plugged in the receptacle? • Is the MAIN POWER switch put to the.
102 Specifications PT -D7700E PT -DW7000E Power supply 220 V – 240 V~, 50 Hz/60 Hz Power consumption 800 W (about 15 W in standby without fan running) DLP TM panel Panel size Display system Number of pixels 0.
103 ENGLISH Interface ports RGB2 input terminal Video input/output terminal S-video input terminal Serial input/output terminal Remote1 input/output terminal Remote2 terminal 1 set of high-density, D-sub 15p (female) [For YP B P R input] Y: 1.0 V [p-p] synchronization signal included, P B P R : 0.
104 Appendix 640 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 1 024 x 768 1 024 x 768 1 024 x 768 1 024 x 768 1 024 x 7.
105 Outside dimensions ENGLISH 540 29 200 530 <Units: mm>.
T rademark Acknowledgement • Digital Light Processing, DLP, and Digital Micromirror Device, DMD are registered trademarks of the Texas Instruments. • VGA and XGA are trademarks of International Business Machines Corporation. • S-VGA is a registered trademark of the Video Electronics Standards Association.
Ein wichtiger Punkt beim Kauf des Geräts Panasonic PT-DW7000E (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Panasonic PT-DW7000E noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Panasonic PT-DW7000E - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Panasonic PT-DW7000E reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Panasonic PT-DW7000E erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Panasonic PT-DW7000E besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Panasonic PT-DW7000E verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Panasonic PT-DW7000E. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Panasonic PT-DW7000E gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
