Benutzeranleitung / Produktwartung P4S533-MX des Produzenten Asus
Zur Seite of 64
Motherboard P4S533-MX User Guide.
ii Checklist Copyright © 2003 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, sto.
iii Features Contents Notices ............................................................................................ v Safety information .......................................................................... vi About this guide ............
iv Safeguards Contents 2.2.2 Legend bar ............................................................. 2-9 2.3 Main Menu ........................................................................ 2-10 2.3.1 Primary and Secondary Master/Slave ............
v Notices Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
vi Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
vii About this guide Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. Where to find more information Refer to the following sources for additional information and for product and software updates.
viii ASUS contact infor mation ASUST eK COMPUTER INC. (Asia-Pacific) Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 General T el: +886-2-2894-3447 General Fax: +886-2-2894-3449 General Email: info@asus.
ix P4S533-MX specifications summar y CPU Chipset Front Side Bus (FSB) Memory Expansion slots VGA IDE Audio LAN (optional) Special features Rear panel I/O Internal I/O (continued on the next page) Socket 478 for Intel ® Pentium ® 4/Celeron On-die 512KB/256KB L2 cache with full speed Supports Intel ® Hyper-Threading T echnology ( since PCB R2.
x BIOS features Industry standard Manageability Form Factor Support CD contents Accessories 2Mb Flash ROM, Award BIOS, TCA V , PnP , DMI2.0, WfM2.0, SM BIOS2.3, CrashFree BIOS, ASUS EZ Flash PCI 2.2, USB 2.0 WfM 2.0. DMI 2.0, WOL/WOR by PME Micro-A TX form factor: 9.
Chapter 1 This chapter describes the features of the P4S533-MX motherboard. It includes brief descriptions of the motherboard components, and illustrations of the layout, jumper settings, and connectors.
1-2 Chapter 1: Product introduction 1 . 1 W elcome! Thank you for buying the ASUS ® P4S533-MX motherboard! The ASUS P4S533-MX motherboard delivers a host of new features and latest technologies makin.
ASUS P4S533-MX motherboard user guide 1-3 1 .3 Motherboard components Before you install the motherboard, learn about its major components and available features to facilitate the installation and future upgrades. Refer to the succeeding pages for the component descriptions.
1-4 Chapter 1: Product introduction A TX 12V connector . This power connector connects the 4-pin 12V plug from the A TX 12V power supply . North bridge controller . This SiS651 controller integrates a high performance host interface for the Intel Pentium 4 processor , a memory controller and SiS MuTIOL technology .
ASUS P4S533-MX motherboard user guide 1-5 PCI slots. These three 32-bit PCI 2.2 expansion slots support bus master PCI cards like SCSI or LAN cards with 133MB/s maximum throughput. LAN PHY . The SiS 962L integrated 10/100Mbps Fast Ethernet with Realtek external PHY supports your local area networking needs.
1-6 Chapter 1: Product introduction 1 .4 Special Features 1.4.1 Product highlights Latest processor technology The P4 S533-MX motherboard supports the latest Intel ® Pentium ® 4 Processor via a 478-pin surface mount ZIF socket. The Pentium 4 processor with 512KB L2 cache on 0.
ASUS P4S533-MX motherboard user guide 1-7 1 .5 Motherboard layout FLOPPY1 P ANEL1 CD1 CHA_F AN1 SiS651 HOST/ Memory Controller AUX1 P4S533-MX ® GAME1 FP_AUDIO1 Super I/O 2Mbit Flash BIOS PCI Slot 1 SEC_IDE1 Accelerated Graphics Port (AGP) USBPWR_34 SiS962L MuTLOL Media I/0 A TX12V1 CPU_F AN1 24.
1-8 Chapter 1: Product introduction 1 .6 Before you pr oceed T ake note of the following precautions before you install motherboard components or change any motherboard settings. 1. Unplug the power cord from the wall socket before touching any component.
ASUS P4S533-MX motherboard user guide 1-9 1 .7 Motherboard ins t allation Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. The motherboard uses the micro-A TX form factor that measures 9.
1-10 Chapter 1: Product introduction 1 .8 Central Pr ocessing Unit (CPU) 1.8.1 Overview The motherboard comes with a surface mount 478-pin Zero Insertion Force (ZIF) socket. The socket is designed for the Intel ® Pentium ® 4 Processor in the 478-pin package with 512/256KB L2 cache on 0.
ASUS P4S533-MX motherboard user guide 1-11 1.8.2 Installing the CPU Follow these steps to install a CPU. 1. Locate the 478-pin ZIF socket on the motherboard. 2. Unlock the socket by pressing the lever sideways, then lift it up to a 90°- 100° angle. 3.
1-12 Chapter 1: Product introduction 1 .9 System memor y The motherboard has two Double Data Rate (DDR) DIMM sockets and two Single Data Rate (SDR) DIMM sockets that supports up to 2GB non-ECC PC2700/2100/ 1600 DDR or PC133/100 SDRAM DIMMs.
ASUS P4S533-MX motherboard user guide 1-13 1 . 10 Expansion slots The motherboard has three PCI slots and one Accelerated Graphics Port (AGP) slot. T o install and configure an expansion card: 1. Install an expansion card following the instructions that came with the chassis.
1-14 Chapter 1: Product introduction 1 . 1 1 Jumpers 1. USB device wake-up (3-pin USBPWR_12, USBPWR_34, USBPWR_56) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices.
ASUS P4S533-MX motherboard user guide 1-15 2. Clear RTC RAM (CLRTC1) This jumper allows you to clear the Real T ime Clock (RTC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data.
1-16 Chapter 1: Product introduction 1. Floppy disk drive connector (34-1 pin FLOPPY1) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug).
ASUS P4S533-MX motherboard user guide 1-17 3. COM1 connector (10-1 pin COM1) This connector accommodates a serial port using an optional serial port bracket. Connect the bracket cable to this connector then install the bracket into a slot opening at the back of the system chassis.
1-18 Chapter 1: Product introduction 5. CPU and Chassis Fan Connectors (3-pin CPU_F AN1, CHA_F AN1) The fan connectors support cooling fans of 350mA~740mA (8.
ASUS P4S533-MX motherboard user guide 1-19 7. USB header (10-1 pin USB_56) If the USB ports on the rear panel are inadequate, a USB header is available for additional USB ports. The USB header complies with USB 2.0 specification that supports up to 480 Mbps connection speed.
1-20 Chapter 1: Product introduction 9. Internal audio connectors (4-pin CD1, AUX1) These connectors allow you to receive stereo audio input from sound sources such as a CD-ROM, TV tuner , or MPEG card. P4S533-MX ® P4S533-MX Internal Audio Connectors CD1 (Black) AUX1 (White ) Right Audio Channel Left Audio Channel Ground Ground 10.
ASUS P4S533-MX motherboard user guide 1-21 1 1. System panel connector (20-pin P ANEL1) This connector accommodates several system front panel functions. • System Power LED Lead (3-1 pin PLED) This 3-1 pin connector connects to the system power LED.
1-22 Chapter 1: Product introduction.
Chapter 2 This chapter tells how to change system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
2-2 Chapter 2: BIOS information 2. 1 Managing and updating your BIOS 2.1.1 Using ASUS EZ Flash to update the BIOS The ASUS EZ Flash feature allows you to easily update the BIOS without having to go through the long process of booting from a diskette and using a DOS-based utility .
ASUS P4S533-MX motherboard user guide 2-3 5. At the prompt, “Please Enter File Name for NEW BIOS: _” , type in the BIOS file name that you downloaded from the ASUS website, then press <Enter>. EZ Flash will automatically access drive A to look for the file name that you typed.
2-4 Chapter 2: BIOS information 2.1.2 Using AFLASH to update the BIOS Creating a bootable disk AFLASH.EXE is a Flash Memory Writer utility that updates the BIOS by uploading a new BIOS file to the programmable flash ROM on the motherboard. This file works only in DOS mode.
ASUS P4S533-MX motherboard user guide 2-5 5. Select 1. Save Current BIOS to File from the Main menu and press <Enter>. The Save Current BIOS T o File screen appears. 6. T ype a filename and the path, for example, A:XXX-XX.XXX, then press <Enter>.
2-6 Chapter 2: BIOS information 6. When prompted to confirm the BIOS update, press Y to start the update. 7. The utility starts to program the new BIOS information into the Flash ROM. The boot block is updated automatically only when necessary . This minimizes the possibility of boot problems in case of update failures.
ASUS P4S533-MX motherboard user guide 2-7 2.1.3 CrashFree BIOS feature The CrashFree BIOS feature allows you to boot the computer from a floppy disk and update the BIOS in case the original BIOS fails or gets corrupted.
2-8 Chapter 2: BIOS information 2.2 BIOS Setup prog r am This motherboard supports a programmable Flash ROM that you can update using the provided utility described in section “ 2.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconfiguring your system, or prompted to “Run Setup”.
ASUS P4S533-MX motherboard user guide 2-9 2.2.2 Legend bar At the bottom of the Setup screen is a legend bar . The keys in the legend bar allow you to navigate through the various setup menus. The following table lists the keys found in the legend bar with their corresponding functions.
2-10 Chapter 2: BIOS information 2.3 Main Menu When you enter the Setup program, the following screen appears. Sub-menu Note that a right pointer symbol (as shown on the left) appears to the left of certain fields. This pointer indicates that you can display a sub-menu from this field.
ASUS P4S533-MX motherboard user guide 2-11 Legacy Diskette A [1.44M, 3.5 in.] Sets the type of floppy drive installed. Configuration options: [None] [360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.] [2.88M, 3.5 in.] Floppy 3 Mode Support [Disabled] This is required to support older Japanese floppy drives.
2-12 Chapter 2: BIOS information 2.3.1 Primary and Secondary Master/Slave T ype [Auto] Select [Auto] to automatically detect an IDE hard disk drive. If automatic detection is successful, Setup automatically fills in the correct values for the remaining fields on this sub-menu.
ASUS P4S533-MX motherboard user guide 2-13 If no drive is installed or if you are removing a drive and not replacing it, select [None]. Other options for the T ype field are: [CD-ROM] - for IDE CD-ROM.
2-14 Chapter 2: BIOS information Maximum LBA Capacity This field shows the drive’s maximum LBA capacity as calculated by the BIOS based on the drive information you entered. Multi-Sector T ransfers [Maximum] This option automatically sets the number of sectors per block to the highest number that the drive supports.
ASUS P4S533-MX motherboard user guide 2-15 CPU External Frequency (MHz) (when CPU Speed is set to [Manual]) This feature tells the clock generator what frequency to send to the system bus and PCI bus. The bus frequency (external frequency) multiplied by the bus multiple equals the CPU speed.
2-16 Chapter 2: BIOS information Memory Frequency [Auto] This field determines whether the memory clock frequency is set to be in synchronous or asynchronous mode with respect to the system frequency . The options that appear in the popup menu vary according to the CPU Frequency (MHz).
ASUS P4S533-MX motherboard user guide 2-17 2.4.1 Chip Configuration SDRAM Configuration [By SPD] This parameter allows you to set the optimal timings for items 2–5, depending on the memory modules that you are using. The default setting is [By SPD], which configures items 2–5 by reading the contents in the SPD (Serial Presence Detect) device.
2-18 Chapter 2: BIOS information Graphics Aperture Size [64MB] This feature allows you to select the size of mapped memory for AGP graphic data. Configuration options: [4MB] [8MB] [16MB] [32MB] [64MB] [128MB] [256MB] AGP Capability [4X Mode] This motherboard supports the AGP 4X interface that transfers video data at 1066MB/s.
ASUS P4S533-MX motherboard user guide 2-19 2.4.2 I/O Device Configuration Floppy Disk Access Control [R/W] When set to [Read Only], this parameter protects files from being copied to floppy disks by allowing reads from, but not writes to, the floppy disk drive.
2-20 Chapter 2: BIOS information 2.4.3 PCI Configuration Slot 1, Slot 2, Slot 3 IRQ [Auto] These fields automatically assign the IRQ for each PCI slot. The default setting for each field is [Auto], which utilizes auto-routing to determine IRQ assignments.
ASUS P4S533-MX motherboard user guide 2-21 2.4.3.1 Onboard PCI Devices Control Onboard LAN [Enabled] This field allows you enable or disable the onboard LAN. Configuration options: [Disabled] [Enabled] Onboard LAN Boot ROM [Disabled] This field allows you enable or disable the onboard LAN Boot ROM feature.
2-22 Chapter 2: BIOS information 2.5 Power Menu The Power menu allows you to reduce power consumption. This feature turns off the video display and shuts down the hard disk after a period of inactivity .
ASUS P4S533-MX motherboard user guide 2-23 Power Management [User Defined] This field allows you to activate or deactivate the automatic power saving features. When set to [Disabled], the power management features do not function regardless of the other settings on this menu.
2-24 Chapter 2: BIOS information 2.5.1 Power Up Control AC PWR Loss Restart [Disabled] This allows you to set whether or not to reboot the system after power interruptions. [Disabled] leaves your system off while [Enabled] reboots the system. [Previous State] sets the system back to the state it was before the power interruption.
ASUS P4S533-MX motherboard user guide 2-25 2.5.2 Hardware Monitor CPU T emperature This item allows you to set the highest temperature for the CPU so that when exceeded by the actual CPU temperature.
2-26 Chapter 2: BIOS information 2.6 Boot Menu Boot Sequence The Boot menu allows you to select among the four possible types of boot devices listed using the up and down arrow keys. By using the <+> or <Space> key , you can promote devices and by using the <-> key , you can demote devices.
ASUS P4S533-MX motherboard user guide 2-27 Reset Configuration Data [No] The Extended System Configuration Data (ESCD) contain information about non- PnP devices. It also holds the complete record of how the system was configured the last time it was booted.
2-28 Chapter 2: BIOS information 2.7 Exit Menu When you have made all of your selections from the various menus in the Setup program, save your changes and exit Setup.
Chapter 3 This chapter describes the contents of the support CD that comes with the motherboard package. Software support.
3-2 Chapter 3: Software support 3. 1 Install an oper ating system This motherboard supports Windows 98SE/ME/NT/2000/XP operating system (OS). Always install the latest OS version and corresponding updates so you can maximize the features of your hardware.
ASUS P4S533-MX motherboard user guide 3-3 3.2.2 Software and drivers installation menus 5.2.3 Software and drivers description The menu lists the drivers and applications that are available for this motherboard. Simply click on a specific item then follow the installation wizard to install it.
3-4 Chapter 3: Software support ASUS Update V3.41.01 This item installs the ASUS Update. This program allows you to download the latest version of the BIOS from the ASUS website. Microsoft Direct X 8.1 Driver This item installs the Microsoft V8.1 driver .
Ein wichtiger Punkt beim Kauf des Geräts Asus P4S533-MX (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Asus P4S533-MX noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Asus P4S533-MX - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Asus P4S533-MX reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Asus P4S533-MX erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Asus P4S533-MX besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Asus P4S533-MX verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Asus P4S533-MX. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Asus P4S533-MX gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
