Benutzeranleitung / Produktwartung M2N-SLI des Produzenten Asus
Zur Seite of 166
Motherboard M2N-SLI Deluxe.
ii E2590 First Edition May 2006 Copyright © 2006 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitte.
iii Contents Notices ........................................................................................................ vii Safety information .................................................................................... viii About this guide .
iv Contents 2.6 Jumper ........................................................................................ 2-20 2.7 Connectors ................................................................................. 2-21 2.7.1 Rear panel connectors ....
v Contents 4.3.8 Usable Memory ............................................................. 4-18 4.4 Advanced menu ......................................................................... 4-19 4.4.1 JumperFree Conguration ........................
vi Contents 5.2.7 Other information ............................................................ 5-6 5.3 Software information ................................................................... 5-8 5.3.1 Cool ‘n’ Quiet!™ T echnology ............
vii Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
viii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
ix About this guide This user guide contains the information you need when installing and conguring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports.
x Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. T ypography Bold text Indicates a menu or an item to select. Italics Used to emphasize a word or a phrase.
xi M2N-SLI Deluxe specications summary (continued on the next page) CPU Socket AM2 for AMD Athlon™ 64 X2 /AMD Athlon™ 64 /AMD Athlon™ 64 FX/AMD Sempron™ processors Supports AMD Cool ‘n’.
xii M2N-SLI Deluxe specications summary High Denition Audio SoundMAX ® ADI AD1988B 8-channel CODEC Supports Jack-Sensing, Enumeration, Multi-Streaming, and Jack-Retasking T echnology Optical an.
xiii M2N-SLI Deluxe specications summary Rear panel 1 x PS/2 keyboard port (purple) 1 x PS/2 mouse port (green) 1 x Serial (COM1) port 1 x IEEE 1394a port 1 x External Serial A T A port 1 x Optical S/PDIF Out port 1 x Coaxial S/PDIF Out port 2 x LAN (RJ-45) ports 4 x USB 2.
xiv.
1 Product introduction This chapter describes the motherboard features and the new technologies it supports..
ASUS M2N-SLI Deluxe Chapter summary 1 1.1 Welcome! ...................................................................................... 1-1 1.2 Package contents ......................................................................... 1-1 1.3 Special features .
ASUS M2N-SLI Deluxe 1-1 1.1 Welcome! Th ank yo u f or b uyi ng an A SUS ® M2N-SLI Deluxe motherboard ! The motherboard delivers a host of new features and latest technologies, making it another stand.
1-2 Chapter 1: Product introduction 1.3 Special features 1.3.1 Product highlights Latest processor technology The motherboard comes with a 940-pin AM2 socket that supports AMD Athlon™ 64 X2/AMD Athlon™ 64/AMD Athlon™ 64 FX/AMD Sempron™ processors.
ASUS M2N-SLI Deluxe 1-3 Serial A T A I/II technology and SA T A-On-The-Go Th e m oth erb oa rd fu lly s up por ts the Serial A T A II 3.0 Gb/s technology through the Serial A T A interfaces and the NVIDIA ® nForce ® 570 SLI™ chipset.
1-4 Chapter 1: Product introduction AMD Cool ‘n’ Quiet T echnology The motherboard supports the AMD Cool ‘n’ Quiet T echnology , which monitors system operation and automatically adjusts CPU voltage and frequency for a cool and quiet operating environment.
ASUS M2N-SLI Deluxe 1-5 Advanced Thermal Design Fanless Design and Heat-pipe The ASUS fanless design allows multi-directional heat ow from major thermal sources in the motherboard to lower overall system temperature, resulting in quieter operation and longer system life.
1-6 Chapter 1: Product introduction Precision T weaker This feature allows you to ne tune the CPU/memory voltage and gradually increase the memory Front Side Bus (FSB) and PCI Express frequency at 1MHz increment to achieve maximum system performance.
2 Hardware information This chapter lists the hardware setup procedures that you have to perform when installing system components. It includes description of the jumpers and connectors on the motherboard.
ASUS M2N-SLI Deluxe Chapter summary 2 2.1 Before you proceed ..................................................................... 2-1 2.2 Motherboard overview ................................................................. 2-2 2.3 Central Processing Unit (CPU) .
ASUS M2N-SLI Deluxe 2-1 Onboard LED The motherboard comes with a standby power LED. The green LED lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component.
2-2 Chapter 2: Hardware information 2.2 Motherboard overview Before you install the motherboard, study the conguration of your chassis to ensure that the motherboard ts into it. 2.2.1 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
ASUS M2N-SLI Deluxe 2-3 2.2.3 Motherboard layout Socket AM2 DDR2 DIMM_B1 (128 bit,240-pin module) DDR2 DIMM_B2 (128 bit,240-pin module) DDR2 DIMM_A1 (128 bit,240-pin module) DDR2 DIMM_A2 (128 bit,240-.
2-4 Chapter 2: Hardware information 2.2.4 Layout contents Slots Page 1. DDR2 DIMM slots 2-1 1 2. PCI slots 2-17 3. PCI Express x1 slots 2-18 4. PCI Express x16 slots 2-18 Jumper Page 1. Clear RTC RAM (3-pin CLR TC) 2-20 Rear panel connectors Page 1. PS/2 mouse port (green) 2-21 2.
ASUS M2N-SLI Deluxe 2-5 Internal connectors Page 1. Floppy disk drive connector (34-1 pin FLOPPY) 2-24 2. IDE connector (40-1 pin PRI_IDE) 2-24 3. NVIDIA ® nForce 570 SLI Serial A T A connectors (7-pin SA T A1 [red], SA T A2 [red], SA T A3 [red], SA T A4 [red], SA T A5 [red], SA T A6 [red]) 2-25 4.
2-6 Chapter 2: Hardware information 2.3.1 Installing the CPU T o install a CPU: 1. Locate the CPU socket on the motherboard. Make sure that the socket lever is lifted up to a 90º angle; otherwise, the CPU will not t in completely . 2. Unlock the socket by pressing the lever sideways, then lift it up to a 90º angle.
ASUS M2N-SLI Deluxe 2-7 3. Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle. 4. Carefully insert the CPU into the socket until it ts in place. 5. When the CPU is in place, push down the socket lever to secure the CPU.
2-8 Chapter 2: Hardware information 2.3.2 Installing the heatsink and fan The AMD Athlon™ 64/AMD Athlon™ 64 FX/AMD Athlon™ 64 X2 and AMD Sempron™ processors require a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance.
ASUS M2N-SLI Deluxe 2-9 2. Attach one end of the retention bracket to the retention module base. 3. Align the other end of the retention bracket (near the retention bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place.
2-10 Chapter 2: Hardware information 5. When the fan and heatsink assembly is in place, connect the CPU fan cable to the connector on the motherboard labeled CPU_F AN.
ASUS M2N-SLI Deluxe 2-11 2.4 System memory 2.4.1 Overview The motherboard comes with four Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets. A DDR2 module has the same physical dimensions as a DDR DIMM but has a 240-pin footprint compared to the 184-pin DDR DIMM.
2-12 Chapter 2: Hardware information Important notice on installing Windows ® XP 32-bit version If you install Windows ® XP 32-bit version Operating System (OS), the limitation of this OS version is that it may reserve a certain amount of memory space for system devices.
ASUS M2N-SLI Deluxe 2-13 DDR2 Size V endor Model Side(s) Component DIMM socket support A* B* C* 512MB KINGSTON E5108AE-6E-E SS KVR667D2N5/512 • • • 1024MB KINGSTON E5108AE-6E-E DS KVR667D2N5/1G .
2-14 Chapter 2: Hardware information Qualied V endors List DDR2-800 DDR2 Size V endor Model Side(s) Component DIMM socket support A* B* C* 512MB KINGSTON K4T51083QC SS KVR800D2N5/512 • • • 10.
ASUS M2N-SLI Deluxe 2-15 2.4.3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components. Failure to do so can cause severe damage to both the motherboard and the components. T o install a DIMM: 1. Unlock a DIMM socket by pressing the retaining clips outward.
2-16 Chapter 2: Hardware information 2.5 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. 2.5.1 Installing an expansion card T o install an expansion card: 1.
ASUS M2N-SLI Deluxe 2-17 2.5.3 Interrupt assignments Standard interrupt assignments * These IRQs are usually available for ISA or PCI devices. IRQ Priority Standard function 0 1 System T imer 1 2 Keyb.
2-18 Chapter 2: Hardware information • In single card mode, we recommend that you use the blue PCI Express x16 (PCIEX16_1) slot. • Due to chipset limitation, the black PCI Express x16 (PCIEX16_2) slot can only operate at x8 speed.
ASUS M2N-SLI Deluxe 2-19 Recommended PCI Express x16 congurations Mode PCIEX16_1 (Blue) slot PCIE16_2 (Black) slot Card type Speed Card type Speed Non-SLI mode PCIe x16 graphics card x16 NA PCIe x1.
2-20 Chapter 2: Hardware information 2.6 Jumper Clear RTC RAM (CLRTC) This jumper allows you to clear the Real T ime Clock (RTC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data.
ASUS M2N-SLI Deluxe 2-21 2.7 Connectors 2.7.1 Rear panel connectors 1. PS/2 mouse port (green). This port is for a PS/2 mouse. 2. Serial port. This 9-pin COM1 port is for pointing devices and other serial devices.
2-22 Chapter 2: Hardware information Refer to the audio conguration table below for the function of the audio ports in 2, 4, 6, or 8-channel conguration. 9. Line Out port (lime). This port connects a headphone or a speaker . In 4-channel, 6-channel, and 8-channel conguration, the function of this port becomes Front Speaker Out.
ASUS M2N-SLI Deluxe 2-23 14. Optical S/PDIF Out port . This port connects an external audio output device via an optical S/PDIF cable. 15. Coaxial S/PDIF Out port. This port connects an external audio output device via an coaxial S/PDIF cable. 16. PS/2 keyboard port (purple) .
2-24 Chapter 2: Hardware information 2.7.2 Internal connectors 1. Floppy disk drive connector (34-1 pin FLOPPY) This connector is for the provided oppy disk drive (FDD) signal cable. Insert one end of the cable to this connector , then connect the other end to the signal connector at the back of the oppy disk drive.
ASUS M2N-SLI Deluxe 2-25 If any device jumper is set as “Cable-Select,” make sure all other device jumpers have the same setting. 3. NVIDIA ® nForce ® 570 SLI MCP Serial A T A connectors (7-pin .
2-26 Chapter 2: Hardware information 4. JMicron JMB363 ® Serial A T A RAID connector (7-pin SA T A_RAID1) This connector is for a Serial A T A signal cable. This connector supports a Serial A T A hard disk drive that you can congure for RAID through the onboard Serial A T A RAID controller .
ASUS M2N-SLI Deluxe 2-27 5. USB connectors (10-1 pin USB56, USB78, USB910) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2.
2-28 Chapter 2: Hardware information 7. CPU, chassis, and power fan connectors (4-pin CPU_F AN, 3-pin CHA_F AN1, 3-pin CHA_F AN2, 3-pin CHA_F AN3, 3-pin CHA_F AN4, 3-pin PWR_F AN) The fan c onnect ors su pport co oling fans o f 350 mA ~ 2000 mA (24 W max.
ASUS M2N-SLI Deluxe 2-29 9. AT X p owe r c on ne cto rs (24-pin A TXPWR, 4-pin EA TX12V) These connectors are for A TX power supply plugs. The power supply plugs are designed to t these connectors in only one orientation. Find the proper orientation and push down rmly until the connectors completely t.
2-30 Chapter 2: Hardware information • For a fully congured system, we recommend that you use a power supply unit (PSU) that complies with A TX 12 V Specication 2.0 (or later version) and provides a minimum power of 600 W . • Do not forget to connect the 4-pin A TX +12 V power plug; otherwise, the system will not boot.
ASUS M2N-SLI Deluxe 2-31 1 1. Optical drive audio co nne cto r (4-pin CD) This connector allows you to receive stereo audio input from an optical drive such as DVD or CD-ROM.. 12. Parallel port con nec tor (26-1 pin LPT) This connector is for a parallel port.
2-32 Chapter 2: Hardware information 13. Digital audio con nec tor (4-1 pin SPDIF_OUT) This connector is for an additional Sony/Philips Digital Interface (S/PDIF) port(s). Connect the S/PDIF In/Out module cable to this connector , then install the module to a slot opening at the back of the system chassis.
ASUS M2N-SLI Deluxe 2-33 • System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector . The system power LED lights up when you turn on the system power , and blinks when the system is in sleep mode.
2-34 Chapter 2: Hardware information Q-Connector (System panel) ASUS Q-Connector allows you to easily to connect the chassis front panel cables to the motherboard. Perform these steps to install ASUS Q-Connector . Step 1 Connect the front panel cables to their respective connectors on the ASUS Q-Connector .
3 Powering up This chapter describes the power up sequence and ways of shutting down the system..
ASUS M2N-SLI Deluxe Chapter summary 3 3.1 Starting up for the rst time ........................................................ 3-1 3.2 Powering off the computer .
ASUS M2N-SLI Deluxe 3-1 3.1 Starting up for the rst time 1. After making all the connections, replace the system case cover . 2. Be sure that all switches are off. 3. Connect the power cord to the power connector at the back of the system chassis. 4.
3-2 Chapter 3: Powering up 3.2 Powering off the computer 3.2.1 Using the OS shut down function If you are using Windows ® 2000: 1. Click the Start button then click Shut Down... 2. Make sure that the Shut Down option button is selected, then click the OK button to shut down the computer .
4 BIOS setup This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
Chapter summary 4 ASUS M2N-SLI Deluxe 4.1 Managing and updating your BIOS ............................................ 4-1 4.2 BIOS setup program .................................................................. 4-10 4.3 Main menu ...................
ASUS M2N-SLI Deluxe 4-1 4.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS Update (Updates the BIOS in Windows ® environment.) 2. ASUS EZ Flash 2 (Updates the BIOS in DOS using a oppy disk, USB ash disk, or the motherboard support CD.
4-2 Chapter 4: BIOS setup Quit all Windows ® applications before you update the BIOS using this utility . 3. Select the ASUS FTP site nearest you to avoid network trafc, or click Auto Select . Click Next . Updating the BIOS through the Internet T o update the BIOS through the Internet: 1.
ASUS M2N-SLI Deluxe 4-3 Updating the BIOS through a BIOS le T o update the BIOS through a BIOS le: 1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate . The ASUS Update main window appears.
4-4 Chapter 4: BIOS setup 4.1.2 Creating a bootable oppy disk 1. Do either one of the following to create a bootable oppy disk. DOS environment a. Insert a 1.44MB oppy disk into the drive. b. At the DOS prompt, type format A: / S then press <Enter>.
ASUS M2N-SLI Deluxe 4-5 T o update the BIOS using EZ Flash 2: 1. Visit the ASUS website (www .asus.com) to download the latest BIOS le for the motherboard. 2. Save the BIOS le to a oppy disk or a USB ash disk, then restart the system. 3. Y ou can launch the EZ Flash 2 by two methods.
4-6 Chapter 4: BIOS setup 4.1.4 Updating the BIOS The Basic Input/Output System (BIOS) can be updated using the AwardBIOS Flash Utility . Follow these instructions to update the BIOS using this utility . 1. Download the latest BIOS le from the ASUS web site.
ASUS M2N-SLI Deluxe 4-7 7. Press <N> when the utility prompts you to save the current BIOS le. The following screen appears. 8. The utility veries the BIOS le in the oppy disk, CD-ROM, or USB ash disk and starts ashing the BIOS le.
4-8 Chapter 4: BIOS setup 4. The utility saves the current BIOS le to the disk, then returns to the BIOS ashing process. 3. T ype a lename for the current BIOS le in the Save current BIOS as eld, then press <Enter>. T o save the current BIOS le using the AwardBIOS Flash Utility: 1.
ASUS M2N-SLI Deluxe 4-9 4.1.6 ASUS CrashFree BIOS 3 utility The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS le when it fails or gets corrupted during the updating process.
4-10 Chapter 4: BIOS setup 4.2 BIOS setup program This motherboard supports a programmable Low-Pin Count (LPC) chip that you can update using the provided utility described in section “4.1 Managing and updating your BIOS.” Use the BIOS Setup program when you are installing a motherboard, reconguring your system, or prompted to“Run Setup.
ASUS M2N-SLI Deluxe 4-11 4.2.1 BIOS menu screen Select Menu Item Specic Help Change the day, month, year and century. Legend bar General help Menu bar Sub-menu items Conguration elds Menu ite.
4-12 Chapter 4: BIOS setup 4.2.4 Menu items The highlighted item on the menu bar displays the specic items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power , Boot, and Exit) on the menu bar have their respective menu items.
ASUS M2N-SLI Deluxe 4-13 4.2.7 Pop-up window Select a menu item then press <Enter> to display a pop-up window with the conguration options for that item.
4-14 Chapter 4: BIOS setup F1:Help ↑↓ : Select Item -/+: Change Value F5: Setup Defaults ESC: Exit →← : Select Menu Enter: Select SubMenu F10: Save and Exit Phoenix-Award BIOS CMOS Setup Utility Main Advanced Power Boot Tools Exit Select Menu Item Specic Help Change the day, month, year and century.
ASUS M2N-SLI Deluxe 4-15 4.3.4 Primary IDE Master/Slave While entering Setup, the BIOS automatically detects the presence of IDE devices. There is a separate sub-menu for each IDE device. Select a device item then press <Enter> to display the IDE device information.
4-16 Chapter 4: BIOS setup Capacity Displays the auto-detected hard disk capacity . This item is not congurable. Cylinder Shows the number of the hard disk cylinders. This item is not congurable. Head Shows the number of the hard disk read/write heads.
ASUS M2N-SLI Deluxe 4-17 4.3.5 SA T A 1, 2, 3, 4, 5, 6 While entering Setup, the BIOS automatically detects the presence of Serial A T A devices. There is a separate sub-menu for each SA T A device. Select a device item then press <Enter> to display the SA T A device information.
4-18 Chapter 4: BIOS setup Head Shows the number of the hard disk read/write heads. This item is not congurable. Landing Zone Shows the number of landing zone per track. This item is not congurable. Sector Shows the number of sectors per track. This item is not congurable.
ASUS M2N-SLI Deluxe 4-19 Phoenix-Award BIOS CMOS Setup Utility Main Advanced Power Boot Tools Exit Select Menu Item Specic Help Adjust system frequency/ voltage. JumperFree Conguration AI NET2 PEG Link Mode CPU Conguration Chipset PCIPnP Onboard Device Conguration 4.
4-20 Chapter 4: BIOS setup Standard Loads the standard settings for the system. AI Overclock Loads overclocking proles with optimal parameters for stability when overclocking. AI N.O.S. The ASUS Non-delay Overclocking System feature intelligently determines the system load and automatically boosts the performance for the most demanding tasks.
ASUS M2N-SLI Deluxe 4-21 CPU Multiplier [Auto] Allows you to set the operating CPU multiplier . The conguration options may vary depending on the type of CPU installed. Conguration options: [Auto] [5x] [6x] ~ [10x] CPU V oltage [Auto] Allows you to set the operating CPU voltage.
4-22 Chapter 4: BIOS setup 4.4.2 AI NET2 F1:Help ↑↓ : Select Item -/+: Change Value F5: Setup Defaults ESC: Exit →← : Select Menu Enter: Select Sub-menu F10: Save and Exit Select Menu Item Specic Help Enable or Disable LAN cable check during POST.
ASUS M2N-SLI Deluxe 4-23 4.4.4 CPU Conguration Select Menu Item Specic Help DRAM timing and control. CPU Conguration CPU Type AMD Engineering Sample CPU Speed 2600 MHz Cache RAM 1024K DRAM Co.
4-24 Chapter 4: BIOS setup DRAM ECC Enable [Disabled] Enables or disables the DRAM ECC function. This item appears only when you install DRAM modules that support ECC function.
ASUS M2N-SLI Deluxe 4-25 Dynamic Idle Cycle Counter Conguration options: [Auto] [Disabled] [Enabled] Idle Cycle Limit Conguration options: [Auto] [0 cycles] [4 cycles] [8 cycles] [16 cycles] [32 cycles] [64 cycles] [128 cycles] [256 cycles] DCQ Bypass Maximum Conguration options: [Auto] [0x] [1x] [2x] [3x].
4-26 Chapter 4: BIOS setup Address/Command Setup T ime Conguration options: [Auto] [1/2 MEMCLK] [1 MEMCLK] Read DQS T iming Control Conguration options: [Auto] [No delay] [1/64 MEMCLK delay] [2/64 MEMCLK delay] [3/64 MEMCLK delay] [4/64 MEMCLK delay] [5/64 MEMCLK delay].
ASUS M2N-SLI Deluxe 4-27 4.4.5 Chipset F1:Help ↑↓ : Select Item -/+: Change Value F5: Setup Defaults ESC: Exit →← : Select Menu Enter: Select Sub-menu F10: Save and Exit Select Menu Item Speci.
4-28 Chapter 4: BIOS setup Select Menu Item Specic Help Select Yes if you are using a Plug and Play capable operating system. Select No if you need the BIOS to congure non-boot devices. PCIPnP Plug & Play O/S [No] Resources Controlled By [Auto] x IRQ Resources Phoenix-Award BIOS CMOS Setup Utility Advanced 4.
ASUS M2N-SLI Deluxe 4-29 Select Menu Item Specic Help Phoenix-Award BIOS CMOS Setup Utility Advanced IDE Function Setup This sub-menu contains IDE function-related items.
4-30 Chapter 4: BIOS setup Select Menu Item Specic Help Phoenix-Award BIOS CMOS Setup Utility Advanced Serial-A T A Conguration This sub-menu allows you to change Serial A T A settings.
ASUS M2N-SLI Deluxe 4-31 Onboard 1394 Controller [Enabled] Allows you to disable or enable the onboard 1394 device support. Conguration options: [Disabled] [Enabled] Onboard 1st/2nd Nvidia LAN [Enabled] Enables or disables the onboard NVIDIA ® LAN controller .
4-32 Chapter 4: BIOS setup 4.5 Power menu The Power menu items allow you to change the settings for the Advanced Conguration and Power Interface (ACPI) and the Advanced Power Management (APM). Select an item then press <Enter> to display the conguration options.
ASUS M2N-SLI Deluxe 4-33 4.5.3 APM Conguration Select Menu Item Specic Help Press [Enter] to select whether or not to restart the system after AC power loss.
4-34 Chapter 4: BIOS setup Power On By RTC Alarm [Disabled] Allows you to enable or disable RTC to generate a wake event. When this item is set to Enabled, the items Date of Month Alarm and T ime (hh:mm:ss) Alarm items become user-congurable with set values.
ASUS M2N-SLI Deluxe 4-35 2.5.4 Hardware Monitor The items in this sub-menu displays the hardware monitor values automatically detected by the BIOS. It also allows you to change CPU Q-Fan feature-related parameters. Select an item then press <Enter> to display the conguration options.
4-36 Chapter 4: BIOS setup The Chassis Q-Fan Prole item becomes user-congurable when you set the Chassis Q-Fan Control item to [Enabled]. Chassis Q-Fan Prole [Performance] Allows you to set the appropriate performance level of the chassis Q-Fan.
ASUS M2N-SLI Deluxe 4-37 4.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu.
4-38 Chapter 4: BIOS setup 4.6.2 Removable Drives 1. Floppy Disks Allows you to assign a removable drive attached to the system. Select Menu Item Specic Help Removable Drives 1. Floppy Disks Phoenix-Award BIOS CMOS Setup Utility Boot 4.6.3 Hard Disk Drives 1.
ASUS M2N-SLI Deluxe 4-39 4.6.5 Boot Settings Conguration F1:Help ↑↓ : Select Item -/+: Change Value F5: Setup Defaults ESC: Exit →← : Select Menu Enter: Select Sub-menu F10: Save and Exit Select Menu Item Specic Help Press [Enter] to enable or disable.
4-40 Chapter 4: BIOS setup T ypematic Rate (Chars/Sec) [6] Allows you to select the rate at which a character repeats when you hold a key . Conguration options: [6] [8] [10] [12] [15] [20] [24] [30] T ypematic Delay (Msec) [250] Allows you to set the delay before keystrokes begin to repeat.
ASUS M2N-SLI Deluxe 4-41 3. When prompted, conrm the password by typing the exact characters again, then press <Enter>. The password eld setting is changed to Set. T o clear the password: 1. Select the password eld and press <Enter> twice.
4-42 Chapter 4: BIOS setup The succeeding items become user-congurable when you enable the ASUS Music Alarm. 4.7 Tools menu The T ools menu items allow you to congure options for special functions. Select an item then press <Enter> to display the sub-menu.
ASUS M2N-SLI Deluxe 4-43 Alarm Date: Sunday/Monday/T uesday/Wednesday/Thursday/Friday/ Saturday [Enabled] Allows you to enable or disable the alarm for a particular day . Conguration options: [Disabled] [Enabled] Alarm Time (hh:mm) 0 : 0 Allows you to set the alarm time.
4-44 Chapter 4: BIOS setup 4.7.2 ASUS O.C. Prole This item allows you to store or load multiple BIOS settings. Select Menu Item Specic Help Press [Enter] to select. ASUS BIOS Prole Load BIOS Prole Save BIOS Prole Phoenix-Award BIOS CMOS Setup Utility Tools Select Menu Item Specic Help Load BIOS Prole from Prole 1.
ASUS M2N-SLI Deluxe 4-45 Select Menu Item Specic Help Save current BIOS Prole to Prole 1. Save BIOS Prole Save to Prole 1 Save to Prole 2 Save to File Phoenix-Award BIOS CMOS Setup Utility Tools Save BIOS Prole Save to Prole 1/2 Allows you to save the current BIOS le to the BIOS Flash.
4-46 Chapter 4: BIOS setup 4.7.4 ASUS EZ Flash 2 Allows you to run ASUS EZ Flash 2. Press <Enter> to start EZ Flash 2 then from the conrmation screen, use the left or right arrows to select [Y es] or [No] then press <Enter>. The following screen appears if you select [Y es].
ASUS M2N-SLI Deluxe 4-47 4.8 Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items.
4-48 Chapter 4: BIOS setup.
5 Software support This chapter describes the contents of the support CD that comes with the motherboard package..
ASUS M2N-SLI Deluxe Chapter summary 5 5.1 Installing an operating system ................................................... 5-1 5.2 Support CD information .............................................................. 5-1 5.3 Software information ...
ASUS M2N-SLI Deluxe 5-1 If Autorun is NOT enabled in your computer , browse the contents of the support CD to locate the le ASSETUP .EXE from the BIN folder . Double-click the ASSETUP .EXE to run the CD. Click an item to install 5.1 Installing an operating system This motherboard supports Windows ® 2000/XP/64-bit XP operating systems (OS).
5-2 Chapter 5: Software support 5.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. Nvidia Chipset Driver Program Installs the NVIDIA ® Chipset drivers for the NVIDIA ® nForce™ 570 SLI chipset.
ASUS M2N-SLI Deluxe 5-3 5.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS Cool ‘n’ Quiet Utility Installs the AMD Cool ‘n’ Quiet™ software.
5-4 Chapter 5: Software support ASUS AI Booster The ASUS AI Booster application allows you to overclock the CPU speed in Windows ® environment. ASUS AI Nap The ASUS AI Nap application allows you to minimize the power consumption of your computer whenever you are away .
ASUS M2N-SLI Deluxe 5-5 Make nVidia 32bit SA T A RAID Driver Make nVidia 64bit SA T A RAID Driver Allows you to create an NVIDIA ® Serial A T A RAID driver disk for a 32-bit/64-bit system. Make JMicron JMB363 RAID Driver Disk Allows you to create a JMicron ® JMB363 RAID driver disk.
5-6 Chapter 5: Software support 5.2.6 ASUS Contact information Click the Contact tab to display the ASUS contact information. Y ou can also nd this information on the inside front cover of this user guide.
ASUS M2N-SLI Deluxe 5-7 Browse this CD Displays the support CD contents in graphical format. T echnical support Form Displays the ASUS T echnical Support Request Form that you have to ll out when requesting technical support.
5-8 Chapter 5: Software support 5.3.1 Cool ‘n’ Quiet!™ T echnology The motherboard supports the AMD Cool ‘n’ Quiet!™ T echnology that dynamically and automatically change the CPU speed, voltage, and amount of power depending on the task the CPU performs.
ASUS M2N-SLI Deluxe 5-9 Windows ® 98 SE/Me 1. From the Windows ® 98 SE/Me operating system, click the Start button. Select Settings, then Control Panel. 2. Do u b l e - c li c k t h e D i s pl a y i c o n i n the Control Panel then select the Screen Saver tab.
5-10 Chapter 5: Software support Launching the Cool ‘n’ Quiet!™ software The motherboard support CD includes the Cool ‘n’ Quiet!™ software that enables you to view your system’s real-time CPU Frequency and voltage. T o launch the Cool ‘n’ Quiet!™ program: 1.
ASUS M2N-SLI Deluxe 5-11 5.3.2 ASUS PC Probe II PC Probe II is a utility that monitors the computer’s vital components, and detects and alerts you of any problem with these components. PC Probe II senses fan rotations, CPU temperature, and system voltages, among others.
5-12 Chapter 5: Software support Button Function Opens the Conguration window Opens the Report window Opens the Desktop Management Interface window Opens the Peripheral Component Interconnect windo.
ASUS M2N-SLI Deluxe 5-13 Changing the monitor panels position T o ch an ge th e po si tio n of t he mo ni tor pan els i n th e des kt op , cli ck the arrow down button of the Scheme options, then select another position from the list box. Click OK when nished.
5-14 Chapter 5: Software support Monitoring sensor alert The monitor panel turns red when a component value exceeds or is lower than the threshold value. Refer to the illustrations below . Large display Small display WMI browser Click to display the W M I ( W i n d o w s M a n a g e m e n t Instrumentation) browser .
ASUS M2N-SLI Deluxe 5-15 PCI browser Click to display the PCI (Peripheral Component Interconnect) browser . This browser provides information on the PCI devices installed o n y o u r s y s t e m . C l i c k t h e p l u s s i g n (+) before the PCI Information item to display available information.
5-16 Chapter 5: Software support Memory usage The Memory tab shows both used and available physical memory . The pie chart at the bottom of the window represents the used (blue) and the available physical memory . Conguring PC Probe II Click to view and adjust the sensor threshold values.
ASUS M2N-SLI Deluxe 5-17 5.3.3 ASUS Music Alarm This motherboard is equipped with an audio alarm clock called ASUS Music Alarm. The ASUS Music Alarm gives you a personal wake-up called with your favorite CD music when the system is off. The onboard audio CODEC supports this feature, which requires an optical drive (CD-ROM, CD-RW , or DVD-ROM).
5-18 Chapter 5: Software support OS conguration T o congure ASUS Music Alarm in Windows ® 1. Place the support CD into the optical drive. 2. Click the Utilities tab and choose ASUS Music Alarm to install the utility . 3. Insert an audio CD into the optical drive.
ASUS M2N-SLI Deluxe 5-19 7. Click the arrow ( ) next to Options in the Options section. The Options panel appears. Disable or select the Repeat mode, then specify the length of the alarm music to play . Set the desired volume. When done, click OK . 8.
5-20 Chapter 5: Software support 5.3.4 ASUS AI Nap This feature allows you to minimize the power consumption of your computer whenever you are away . Enable this feature for minimum power consumption and a more quiet system operation.
ASUS M2N-SLI Deluxe 5-21 5.3.5 ASUS AI Gear ASUS AI Gear provides four system performance options that allows you to select the best performance setting for your computing needs. This easy-to-use utility adjusts the processor frequency and vCore voltage to minimize system noise and power consumption.
5-22 Chapter 5: Software support Y ou can also set the AI Gear modes by clicking the AI Gear icon on the Windows taskbar . • When AI Gear is enabled, the system will automatically optimize the CPU and chassis fan speed according to the system loading.
ASUS M2N-SLI Deluxe 5-23 5.3.6 SoundMAX ® High Denition Audio utility The ADI AD1988B High Definition Audio CODEC provides 8-channel audio capability through the SoundMAX ® audio utility with AudioESP™ software to deliver the ultimate audio experience on your PC.
5-24 Chapter 5: Software support From the taskbar , double-click on the SoundMAX ® icon to display the SoundMAX ® Control Panel. Audio Setup Wizard By clicking the icon from the SoundMAX ® control panel, you can easily congure your audio settings.
ASUS M2N-SLI Deluxe 5-25 Jack conguration This screen helps you congure your computer’s audio ports, depending on the audio devices you have installed. Adjust speaker volume This screen helps you adjust speaker volume. Click the T est button to hear the changes you have made.
5-26 Chapter 5: Software support Audio preferences Click the icon to go to the Preferences page. This page allows you to change various audio settings. General options Click the General tab to choose your playback and recording devices, enable/ disable the AudioESP™ feature, and enable/disable digital output.
ASUS M2N-SLI Deluxe 5-27 Enhanced Microphone Features V oice recording Enables Noise Filter function. Detects repetitive and stationary noises like computer fans, air conditioners, and other background noises then eliminates it in the incoming sudio stream while recording.
5-28 Chapter 5: Software support 5.4 RAID congurations The motherboard comes with the NVIDIA ® nForce™ 570 SLI MultiShield™ and JMicro ® JMB363 RAID controllers that allow you to congure Serial A T A hard disk drives as RAID sets. The motherboard supports the following RAID congurations.
ASUS M2N-SLI Deluxe 5-29 5.4.1 Installing hard disks The motherboard supports Serial A T A hard disk drives. For optimal performance, install identical drives of the same model and capacity when creating a disk array . Installing Serial A T A (SA T A) hard disks T o install the SA T A hard disks for a RAID conguration: 1.
5-30 Chapter 5: Software support 5.4.2 NVIDIA ® MediaShield™ RAID congurations The motherboard includes a high performance SA T A RAID controller integrated in the NVIDIA ® nForce™ 570 SLI southbridge chipset. It supports RAID 0, RAID 1, RAID 0+1, RAID 5 and JBOD for six independent Serial A T A channels.
ASUS M2N-SLI Deluxe 5-31 Entering the NVIDIA ® MediaShield RAID utility T o enter the NVIDIA ® RAID utility: 1. Boot up your computer . 2. During POST , press <F10> to display the main menu of the utility . The RAID BIOS setup screens shown in this section are for reference only , and may not exactly match the items on your screen.
5-32 Chapter 5: Software support TIP: For server systems, we recommend using a lower array block size. For multimedia computer systems used mainly for audio and video editing, we recommend a higher array block size for optimum performance. T ake caution in using this option.
ASUS M2N-SLI Deluxe 5-33 Rebuilding a RAID array T o rebuild a RAID array: 1. From the Array List menu, use the up or down arrow keys to select a RAID array then press <Enter>.
5-34 Chapter 5: Software support A new set of navigation keys is displayed on the bottom of the screen. 2. Press <R> to rebuild a RAID array . The following screen appears. 3. Use the up or down arrow keys to select a RAID array to rebuild, then press <F7>.
ASUS M2N-SLI Deluxe 5-35 Deleting a RAID array T o delete a RAID array: 1. From the Array List menu, use the up or down arrow keys to select a RAID array then press <Enter>. The RAID Array details appear . [R] Rebuild [D] Delete [C] Clear Disk [ENTER] Return Array 1 : NVIDIA MIRROR XXX.
5-36 Chapter 5: Software support Clearing a disk data T o clear disk data: 1. From the Array List menu, use the up or down arrow keys to select a RAID array then press <Enter>. The RAID Array details appear . [R] Rebuild [D] Delete [C] Clear Disk [ENTER] Return Array 1 : NVIDIA MIRROR XXX.
ASUS M2N-SLI Deluxe 5-39 5.4.3 JMicron ® RAID Conguration The JMicron ® Serial A T A controller allows you to congure RAID 0 and RAID 1 sets on the external Serial A T A hard disk drives. Before creating a RAID set Prepare the following items: • At two HDDs, preferably with the same model and capacity .
5-40 Chapter 5: Software support Entering the JMB363 RAID BIOS utility 1. During POST , press <Ctrl-J> to enter the JBM363 RAID BIOS menu. 2. The main JMB363 RAID BIOS menu appears. 3. Use the arrow keys to move the color bar and navigate through the items.
ASUS M2N-SLI Deluxe 5-41 2. When the Level item is highlighted, use the up/down arrow key to select the RAID set that you want to create. 3. When the Disks item is highlighted, use the up/down arrow key to highlight an HDD that you want to belong to the RAID set, then press the space bar to conrm selection.
5-42 Chapter 5: Software support 5. When done, press <Enter> to conrm the creation of the RAID set. A dialogue box appears to conrm the action. Press <Y> to conrm; otherwise, press <N>. Pressing <Y> deletes all the data in the HDDs.
ASUS M2N-SLI Deluxe 5-43 Deleting a RAID set 1. In the main JMB363 RAID BIOS menu, highlight Delete RAID Disk Drive using the up/down arrow key then press <Enter>. 2. Use the space bar to select the RAID set you want to delete. A selected set shows a sign before it.
5-44 Chapter 5: Software support Resetting disks to non-RAID When you install an HDD that has been congured as part of another RAID set, you may convert this broken RAID HDD to non-RAID mode.
ASUS M2N-SLI Deluxe 5-45 5.5 Creating a RAID driver disk A oppy disk with the RAID driver is required when installing Windows ® 2000/XP operating system on a hard disk drive that is included in a RAID set. T o create a RAID driver disk: 1. Place the motherboard support CD into the CD-ROM drive.
5-46 Chapter 5: Software support.
6 This chapter tells how to install SLI-ready PCI Express graphics cards. NVIDIA ® SLI™ technology support.
ASUS M2N-SLI Deluxe Chapter summary 6.1 Overview ............................................................................... 6-1 6.2 Dual graphics cards setup .
ASUS M2N-SLI Deluxe 6-1 6.1 Overview The motherboard supports the NVIDIA ® SLI™ (Scalable Link Interface) - Intel ® Edition technology that allows you to install two identical PCI Express™ x16 graphics cards. Follow the installation procedures in this section.
6-2 Chapter 6: NVIDIA ® SLI™ technology support 6.2 Dual graphics card setup 6.2.1 Installing SLI-ready graphics cards Install only identical SLI-ready graphics cards that are NVIDIA ® -certied. Different types of graphics cards will not work together properly .
ASUS M2N-SLI Deluxe 6-3 4. Insert the second graphics card into the other slot. Make sure that the card is properly seated on the slot. If required, connect an auxiliary power source to the PCI Express graphics cards. 3. Insert one graphics card into either the blue or black slot.
6-4 Chapter 6: NVIDIA ® SLI™ technology support 7. Connect a VGA cable or a DVI-I cable to the graphics card/s. We recommend to install an additional chassis fan for better thermal environment. 5. Align and insert the SLI connector to the goldngers on each graphics card.
ASUS M2N-SLI Deluxe 6-5 NVIDIA Settings icon T o enable the multi-GPU feature: 1. Click the NVIDIA Settings icon on your Windows taskbar . 2. F r o m t h e p o p - u p m e n u , s e l e c t nView Desktop Manager then click nView Properties. Make sure that your PCI Express graphics card driver supports the NVIDIA SLI technology .
6-6 Chapter 6: NVIDIA ® SLI™ technology support 5. From the Display Properties dialog b o x , s e l e c t t h e S e t t i n g s t ab t h e n click Advanced. 6. Select the NVIDIA GeForce tab. 7 . Click the slider to display the following screen, then select the SLI multi-GPU item.
Ein wichtiger Punkt beim Kauf des Geräts Asus M2N-SLI (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Asus M2N-SLI noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Asus M2N-SLI - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Asus M2N-SLI reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Asus M2N-SLI erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Asus M2N-SLI besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Asus M2N-SLI verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Asus M2N-SLI. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Asus M2N-SLI gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
