Benutzeranleitung / Produktwartung M2N-MX SE PLUS des Produzenten Asus
Zur Seite of 90
M o t h e r b o a r d M2N-MX SE PLUS.
ii Copyright © 2007 ASUST eK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a r.
iii Contents Notices ......................................................................................................... vi Safety information ..................................................................................... vii About this guide .
iv Contents Chapter 2: BIOS setup 2.1 Managing and updating your BIOS ............................................ 2-2 2.1.1 Creating a bootable oppy disk ....................................... 2-2 2.1.2 ASUS EZ Flash utility .....................
v Contents 2.5.3 ACPI APIC Support [Enabled] ....................................... 2-2 9 2.5.4 APM Conguration ........................................................ 2-30 2.5.5 Hardware Monitor ..................................................
vi Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
vii Safety information Electrical safety • T o prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system. • When adding or removing devices to or from the system, ensure that the power cables for the devices are unplugged before the signal cables are connected.
viii About this guide This user guide contains the information you need when installing and conguring the motherboard. How this guide is organized This guide contains the following parts: • Chapter 1: Product introduction This chapter describes the features of the motherboard and the new technology it supports.
ix Conventions used in this guide T o make sure that you perform certain tasks properly , take note of the following symbols used throughout this manual. T ypography Bold text Indicates a menu or an item to select. Italics Used to emphasize a word or a phrase.
x M2N-MX SE PLUS specications summary (continued on the next page) CPU Chipset Front Side Bus Memory Expansion slots Graphics Storage High Denition Audio LAN USB Special features BIOS features S.
xi M2N-MX SE PLUS specications summary Rear panel Internal Connector Accessories Manageability Form Factor Support CD contents 1 x Parallel port 1 x LAN (RJ-45) port 4 x USB 2.0 ports 1 x VGA port 1 x COM1 port 1 x PS / 2 keyboard port 1 x PS / 2 mouse port 5.
xii.
1 Product introduction This chapter describes the motherboard features and the new technologies it supports..
1-2 Chapter 1: Product introduction 1.1 Welcome! Thank you for buying an ASUS ® M2N-MX SE PLUS motherboard! The motherboard delivers a host of new features and latest technologies, making it another .
ASUS M2N-MX SE PLUS 1-3 NVIDIA ® GeForce™ 6100 GPU and NVIDIA ® nForce™ 430 MCP chipsets The NVIDIA ® GeForce™ 6100 Graphics Processing Unit (GPU) Northbridge supports Microsoft ® DirectX 9.
1-4 Chapter 1: Product introduction 10 / 100 Mbps LAN Easy connectivity to your network or broadband connection with the onboard LAN port. Allows you to play online games without buying expensive additional LAN cards. See page 1-23 for details. USB 2.
ASUS M2N-MX SE PLUS 1-5 1.3.2 Innovative ASUS features ASUS CrashFree BIOS 2 Thi s feat ure al lows y ou to re store the or igina l B IOS data from t he su ppo rt CD in case whe n the BIOS c odes a nd da ta are co rrupte d. Th is pro tectio n elim inate s t he need t o buy a rep laceme nt BIOS chip.
1-6 Chapter 1: Product introduction Onboard LED The motherboard comes with a standby power LED that lights up to indicate that the system is ON, in sleep mode, or in soft-off mode. This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component.
ASUS M2N-MX SE PLUS 1-7 1.5.1 Motherboard layout 1.5 Motherboard overview 19.3cm (7.6in) DDR2 DIMM_A1 (64 bit,240-pin module) DDR2 DIMM_B1 (64 bit,240-pin module) 24.
1-8 Chapter 1: Product introduction R M2N-MX SE PLUS Do not overtighten the screws! Doing so can damage the motherboard. 1.5.2 Placement direction When installing the motherboard, make sure that you place it into the chassis in the correct orientation.
ASUS M2N-MX SE PLUS 1-9 1.6 Central Processing Unit (CPU) The motherboard comes with a 940-pin AM2+ socket designed for the AMD Athlon™ 64 X2 / Athlon™ 64 / Athlon™ FX / Sempron™ processor . The AM2+ socket has a different pinout from the 940-pin socket designed for the AMD Opteron™ processor .
1-10 Chapter 1: Product introduction 3. Position the CPU above the socket such that the CPU corner with the gold triangle matches the socket corner with a small triangle. 4. Carefully insert the CPU into the socket until it ts in place. The CPU ts only in one correct orientation.
ASUS M2N-MX SE PLUS 1-1 1 1.6.2 Installing the heatsink and fan The AMD Athlon™ 64 X2 / Athlon™ 64 / Athlon™ FX / Sempron™ processor requires a specially designed heatsink and fan assembly to ensure optimum thermal condition and performance. Follow these steps to install the CPU heatsink and fan.
1-12 Chapter 1: Product introduction 2. Attach one end of the retention bracket to the retention module base. 3. Align the other end of the retention bracket (near the retention bracket lock) to the retention module base. A clicking sound denotes that the retention bracket is in place.
ASUS M2N-MX SE PLUS 1-13 1.7.2 Memory congurations Y ou may install 256 MB, 512 MB, 1 GB, and 2 GB unbuffered non-ECC DDR2 DIMMs into the DIMM sockets. 1.7 System memory 1.7.1 Overview The motherboard comes with two Double Data Rate 2 (DDR2) Dual Inline Memory Modules (DIMM) sockets.
1-14 Chapter 1: Product introduction Qualied V endors Lists (QVL) DDR2-1066 DDR2-800 Size V endor Model CL Brand SS/DS Component DIMM support A B 512MB Kingston KHX8500D2/512 N/A Kingston SS Heat-S.
ASUS M2N-MX SE PLUS 1-15 DDR2-667 Size Vendor Model CL Brand SS/DS Component DIMM support A B 256MB Kingston KVR667D2N5/256 N/A Kingston SS D3216TLSAKL3U • • 256MB Kingston KVR667D2N5/256 N/A In.
1-16 Chapter 1: Product introduction Side(s) : SS - Single-sided DS - Double-sided DIMM Support: A - Supports one module inserted in any slot for a single-channel memory conguration. B - Supports one pair of modules inserted into the yellow slots. Visit the ASUS website (www.
ASUS M2N-MX SE PLUS 1-17 1.7.3 Installing a DIMM 1. Unlock a DIMM socket by pressing the retaining clips outward. 2. Align a DIMM on the socket such that the notch on the DIMM matches the break on the socket. 3. Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated.
1-18 Chapter 1: Product introduction 1.8 Expansion slots In the future, you may need to install expansion cards. The following sub-sections describe the slots and the expansion cards that they support. 1.8.1 Installing an expansion card T o install an expansion card: 1.
ASUS M2N-MX SE PLUS 1-19 IRQ Priority Standard Function 0 1 System T imer 1 2 Keyboard Controller 2 – Re-direct to IRQ#9 3 1 1 IRQ holder for PCI steering* 4 12 Communications Port (COM1)* 5 13 IRQ .
1-20 Chapter 1: Product introduction 1.8.3 PCI slots The PCI slots support cards such as a LAN card, SCSI card, USB card, and other cards that comply with PCI specications.
ASUS M2N-MX SE PLUS 1-21 1.9 Jumpers 1. Clear RTC RAM (CLRTC) This jumper allows you to clear the Real T ime Clock (RTC) RAM in CMOS. Y ou can clear the CMOS memory of date, time, and system setup parameters by erasing the CMOS RTC RAM data.
1-22 Chapter 1: Product introduction 2. USB device wake-up (3-pin PS2_USBPW1-4, USBPW5-8) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices.
ASUS M2N-MX SE PLUS 1-23 Refer to the audio conguration table for the function of the audio ports in 2, 4, or 6-channel conguration. 1.10 Connectors 1.10.1 Rear panel connectors 1. PS/2 mouse port (green). This port is for a PS/2 mouse. 2. Parallel port.
1-24 Chapter 1: Product introduction 7. USB 2.0 ports 1 and 2. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.0 devices. 8. USB 2.0 ports 3 and 4. These two 4-pin Universal Serial Bus (USB) ports are available for connecting USB 2.
ASUS M2N-MX SE PLUS 1-25 2. IDE connector (40-1 pin PRI_IDE) The onboard IDE connector is for Ultra DMA 133/100/66/33 signal cable. There are three connectors on each Ultra DMA 133/100/66/33 signal cable: blue, black, and gray .
1-26 Chapter 1: Product introduction 3. Serial A T A connectors (7-pin SA T A1, SA T A2) These connectors are for the Serial A T A signal cables for Serial A T A 3.0 Gb/s hard disk and optical disk drives. The Serial A T A 3 Gb/s is backward compatible with Serial A T A 1.
ASUS M2N-MX SE PLUS 1-27 4. CPU and Chassis Fan connectors (4-pin CPU_F AN, 3-pin CHA_F AN) The fan c onnect ors su pport cooli ng fan s of 3 50mA~ 740 mA (8.
1-28 Chapter 1: Product introduction Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! 6. USB connectors (10-1 pin USB56, USB78) These connectors are for USB 2.0 ports. Connect the USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis.
ASUS M2N-MX SE PLUS 1-29 8. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either High Denition Audio or AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector .
1-30 Chapter 1: Product introduction 10. A TX power connectors (24-pin EA TXPWR, 4-pin A TX12V) These connectors are for A TX power supply plugs. The plugs from the power supply are designed to t these connectors in only one orientation. Find the proper orientation and push down rmly until the connectors completely t.
ASUS M2N-MX SE PLUS 1-31 1 1. System panel connector (10-1 pin F_P ANEL) This connector supports several chassis-mounted functions. • System power LED (2-pin PWRLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector .
1-32 Chapter 1: Product introduction.
2 BIOS setup This chapter tells how to change the system settings through the BIOS Setup menus. Detailed descriptions of the BIOS parameters are also provided.
2-2 Chapter 2: BIOS setup 2.1 Managing and updating your BIOS The following utilities allow you to manage and update the motherboard Basic Input/Output System (BIOS) setup. 1. ASUS EZ Flash: Updates the BIOS in DOS mode using a oppy disk or the motherboard support CD.
ASUS M2N-MX SE PLUS 2-3 2. Co py the or ig in al or th e lat est mo th er boa rd BI OS l e t o t he b oot abl e op py dis k. 2.1.2 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a oppy disk and using a DOS-based utility .
2-4 Chapter 2: BIOS setup 2.1.3 AFUDOS utility The AFUDOS utility allows you to update the BIOS le in DOS environment using a bootable oppy disk with the updated BIOS le. This utility also allows you to copy the current BIOS le that you can use as backup when the BIOS fails or gets corrupted during the updating process.
ASUS M2N-MX SE PLUS 2-5 Updating the BIOS le T o update the BIOS le using the AFUDOS utility: 1. Visit the ASUS website (www .asus.com) and download the latest BIOS le for the motherboard. Save the BIOS le to a bootable oppy disk. 2. Copy the AFUDOS utility (afudos.
2-6 Chapter 2: BIOS setup 2.1.4 ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS le when it fails or gets corrupted during the updating process. Y ou can update a corrupted BIOS le using the motherboard support CD or the oppy disk that contains the updated BIOS le.
ASUS M2N-MX SE PLUS 2-7 Recovering the BIOS from the support CD T o recover the BIOS from the support CD: 1. Remove any oppy disk from the oppy disk drive, then turn on the system.
2-8 Chapter 2: BIOS setup Installing ASUS Update T o install ASUS Update: 1. Place the support CD in the optical drive. The Drivers menu appears. 2. Click the Utilities tab, then click Install ASUS Update . See page 3-4 for the Utilities screen menu. 3.
ASUS M2N-MX SE PLUS 2-9 3. Select the ASUS FTP site nearest you to avoid network trafc, or click Auto Select . Click Next . Updating the BIOS through the Internet T o update the BIOS through the Internet: 1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate .
2-10 Chapter 2: BIOS setup Updating the BIOS through a BIOS le T o update the BIOS through a BIOS le: 1. Launch the ASUS Update utility from the Windows ® desktop by clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate . The ASUS Update main window appears.
ASUS M2N-MX SE PLUS 2-1 1 • The default BIOS settings for this motherboard apply for most conditions to ensure optimum performance. If the system becomes unstable after changing any BIOS settings, load the default settings to ensure system compatibility and stability .
2-12 Chapter 2: BIOS setup 2.2.2 Menu bar The menu bar on top of the screen has the following main items: Main For changing the basic system conguration Advanced For changing the advanced system se.
ASUS M2N-MX SE PLUS 2-13 2.2.4 Menu items The highlighted item on the menu bar displays the specic items for that menu. For example, selecting Main shows the Main menu items. The other items (Advanced, Power , Boot, and Exit) on the menu bar have their respective menu items.
2-14 Chapter 2: BIOS setup 2.3 Main menu When you enter the BIOS Setup program, the Main menu screen appears, giving you an overview of the basic system information. 2.3.1 System Time [xx:xx:xx] Allows you to set the system time. 2.3.2 System Date [Day xx/xx/xxxx] Allows you to set the system date.
ASUS M2N-MX SE PLUS 2-15 2.3.4 IDE Conguration The items in this menu allow you to set or change the congurations for the IDE devices installed in the system.
2-16 Chapter 2: BIOS setup The BIOS automatically detects the values opposite the dimmed items (Device, V endor , Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra DMA, and SMART monitoring). These values are not user-congurable. These items show N/A if no IDE device is installed in the system.
ASUS M2N-MX SE PLUS 2-17 2.3.6 SA T A1 and SA T A2 While entering Setup, the BIOS automatically detects the presence of SA T A devices. There is a separate sub-menu for each SA T A device. Select a device item then press <Enter> to display the SA T A device information.
2-18 Chapter 2: BIOS setup PIO Mode [Auto] Selects the PIO mode. Conguration options: [Auto] [0] [1] [2] [3] [4] DMA Mode [Auto] Selects the DMA mode.
ASUS M2N-MX SE PLUS 2-19 2.4 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. T ake caution when changing the settings of the Advanced menu items. Incorrect eld values can cause the system to malfunction.
2-20 Chapter 2: BIOS setup This option should remain disabled for the normal operation. The driver developer may enable it for testing purpose 2.4.1 CPU Conguration The items in this menu show the CPU-related information that the BIOS automatically detects.
ASUS M2N-MX SE PLUS 2-21 AMD Overclocking Conguration AMD Overclocking Conguration Processor Frequency Multiplier [Auto] Processor Voltage [Auto] Processor Frequency Multiplier [Auto] Sets the processor frenquency multiplier . Conguration options: [Auto] [x5.
2-22 Chapter 2: BIOS setup NorthBridge Configuration 2.4.2 Chipset The Chipset menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu. Advanced Chipset Settings WARNING: Setting wrong values in below sections may cause the system to malfunction.
ASUS M2N-MX SE PLUS 2-23 Channel Interleaving [Auto] Allows you to enable or disable channel memory interleaving. Conguration options: [Disabled] [Auto] Enable Clock to All DIMMs [Disabled] All ows yo u to e nable or di sab le the Unuse d Clo cks to DIMMs Even Memor y Slo ts are not p opulat ed.
2-24 Chapter 2: BIOS setup SouthBridge MCP61 chipset Conguration Primary Graphics Adapter [PCIE-> PCI -> IGP] OnChip VGA Frame Buffer Size [128M] AZALIA Audio [Auto] Front Panel Select [HD Au.
ASUS M2N-MX SE PLUS 2-25 2.4.3 Onboard Devices Conguration Congure ITE8712 Super IO Chipset Serial Port1 Address [3F8/IRQ4] Parallel Port Address [378] Parallel Port Mode [Normal] Parallel Port IRQ [IRQ7] Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address.
2-26 Chapter 2: BIOS setup 2.4.4 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices.
ASUS M2N-MX SE PLUS 2-27 USB 1.1 Controller [Enabled] Allows you to enable or disable the USB 1.1 Controller . Conguration options: [Enabled] [Disabled] USB 2.
2-28 Chapter 2: BIOS setup USB Mass Storage Device Conguration USB Mass Storage Device Conguration USB Mass Storage Reset Delay [20 Sec] Device #1 Netac Emulation Type [Auto] USB Mass Storage Reset Delay [20 Sec] Allows you to set the numbers of seconds POST waits for the USB mass storage device after start unit command.
ASUS M2N-MX SE PLUS 2-29 2.5 Power menu The Power menu items allow you to change the settings for the Advanced Power Management (APM). Select an item then press <Enter> to display the conguration options.
2-30 Chapter 2: BIOS setup 2.5.4 APM Conguration APM Conguration Power Button Mode [On/Off] Restore on AC Power Loss [Power Off] Power On By PCI(-E) Device [Disabled] Power On By Ring [Disabled].
ASUS M2N-MX SE PLUS 2-31 2.5.5 Hardware Monitor Hardware Monitor CPU Temperature [51ºC/123.5ºF] MB Temperature [36ºC/96.5ºF] CPU Fan Speed (RPM) [3325RPM] Chassis Fan1 Speed [N/A] VCORE Voltage [ 1.376V] 3.3V Voltage [ 3.312V] 5V Voltage [ 5.068V] 12V Voltage [11.
2-32 Chapter 2: BIOS setup 2.6 Boot menu The Boot menu items allow you to change the system boot options. Select an item then press <Enter> to display the sub-menu.
ASUS M2N-MX SE PLUS 2-33 2.6.3 Boot Settings Conguration Select Screen Select Item +- Change Option F1 General Help F10 Save and Exit ESC Exit Boot Settings Conguration Quick Boot [Enabled] Full.
2-34 Chapter 2: BIOS setup If you forget your BIOS password, you can clear clear it by erasing the CMOS Real T ime Clock (RTC) RAM. See section “1.9 Jumpers” for information on how to erase the RTC RAM. Interrupt 19 Capture [Disabled] When set to [Enabled], this function allows the option ROMs to trap Interrupt 19.
ASUS M2N-MX SE PLUS 2-35 User Access Level [Full Access] This item allows you to select the access restriction to the Setup items. Conguration options: [No Access] [View Only] [Limited] [Full Access] No Access prevents user access to the Setup utility .
2-36 Chapter 2: BIOS setup Exit & Discard Changes Select this option only if you do not want to save the changes that you made to the Setup program. If you made changes to elds other than System Date, System T ime, and Password, the BIOS asks for a conrmation before exiting.
3 Software support This chapter describes the contents of the support CD that comes with the motherboard package..
3-2 Chapter 3: Software support If Autorun is NOT enabled in your computer , browse the contents of the support CD to locate the le ASSETUP .EXE from the BIN folder .
3-3 ASUS M2N-MX SE PLUS 3.2.2 Drivers menu The drivers menu shows the available device drivers if the system detects installed devices. Install the necessary drivers to activate the devices. ASUS Installl-Drivers Installation Wizard Installs the ASUS Install-Drivers Installation Wizard.
3-4 Chapter 3: Software support 3.2.3 Utilities menu The Utilities menu shows the applications and other software that the motherboard supports. ASUS InstAll - Installation Wizard for Utilities Installs all of the utilities through the installation Wizard.
3-5 ASUS M2N-MX SE PLUS 3.2.4 Make Disk menu The Make Disk menu allows you to make a RAID driver disk. NVIDIA ® 32bit 2000 SA T A RAID Driver Allows you to create an NVIDIA ® Serial A T A (SA T A) R.
3-6 Chapter 3: Software support NVIDIA ® SA T A RAID User’s Manual Allows you to open the NVIDIA ® SA T A RAID user’s manual. HD Audio User’s Manual Allows you to open the HD Audio user’s manual. 3.2.5 Manual menu The Manual menu contains a list of supplementary user manuals.
3-7 ASUS M2N-MX SE PLUS 3.2.6 ASUS Contact information Click the Contact tab to display the ASUS contact information. Y ou can also nd this information on the inside front cover of this user guide.
3-8 Chapter 3: Software support T echnical support Form Displays the ASUS T echnical Support Request Form that you have to ll out when requesting technical support. Filelist Displays the contents of the support CD and a brief description of each in text format.
3-9 ASUS M2N-MX SE PLUS 3.3 Creating a RAID driver disk A oppy disk with the RAID driver is required when installing Windows ® 2000/XP/ Vista operating system on a hard disk drive that is included in a RAID set. T o create a RAID driver disk: 1. Place the motherboard support CD into the CD-ROM drive.
3-10 Chapter 3: Software support.
Ein wichtiger Punkt beim Kauf des Geräts Asus M2N-MX SE PLUS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Asus M2N-MX SE PLUS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Asus M2N-MX SE PLUS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Asus M2N-MX SE PLUS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Asus M2N-MX SE PLUS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Asus M2N-MX SE PLUS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Asus M2N-MX SE PLUS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Asus M2N-MX SE PLUS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Asus M2N-MX SE PLUS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
