Benutzeranleitung / Produktwartung Genie des Produzenten Asus
Zur Seite of 26
Book Size PC System ® Genie Installation Guide.
2 Checklist Disclaimer/Copyrights No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated .
3 Features ASUS Contact Information ASUST eK COMPUTER INC. (Asia-Pacific) Marketing Address: 150 Li-T e Road, Peitou, T aipei, T aiwan 1 12 T elephone: +886-2-2894-3447 Fax: +886-2-2894-3449 Email: info@asus.com.tw T echnical Support T el (English): +886-2-2890-7123 T el (Chinese): +886-2-2890-71 13 Fax: +886-2-2893-7775 Email: tsd@asus.
4 Safeguards FCC/CDC Statements Federal Communications Commission Statement This device complies with FCC Rules Part 15. Operation is subject to the following two conditions: • This device may not cause harmful interference, and • This device must accept any interference received including interference that may cause undesired operation.
5 T able of Contents Disclaimer/Copyrights ....................................................... 2 ASUS Contact Information ................................................ 3 FCC/CDC Statements .......................................................
6 System Package Contents The following checklist enumerates the components included in the standard system package. 1) System Chassis 2) ASUS POLO Motherboard 3) Switching Power Supply 4) ASUS 24X CD-ROM Drive 5) CD-ROM Adapter Board 6) 1.
7 Genie Book Size PC System Y ou are reading the Genie Book Size PC System Installation Guide. This reference guide provides general information about the Genie Book Size PC System. “ About This Guide ” contains an introduction on the contents of this document that include target audience and chapter description.
8 Introduction: About This Manual Checklist This installation guide contains the following parts: 1. Introduction: About This Guide This part contains an introduction on the contents of this document that include target audience and chapter description.
9 Genie Book Size PC System This chapter includes step-by-step instructions on how to install components in the Genie Book Size PC System. Chapter 1 System Assembly IMPORT ANT : The Genie Book Size PC System chassis is suitable only for Flex A TX motherboards up to 20cm wide.
10 Chapter 1: System Assemby Opening the Chassis 1. Remove the two screws (indicated by black circles) on the back panel that secure the top cover to the chassis. 2. Slide the top cover towards the back panel, then lift it off the chassis. 3. Detach the front panel by lifting the holding tabs on top.
Genie Book Size PC System 11 Installing Disk Drives 1. Detach the CD-ROM frame by sliding it back for a quarter of an inch then lifting it up. 2. Carefully insert a slim CD- ROM drive into the frame as shown. 3. Secure the slim CD-ROM drive with two screws (one on each side).
12 Chapter 1: System Assemby Installing Disk Drives 6. Insert a floppy disk drive into the FDD bay as shown. 7. Secure the floppy drive to the frame using four screws (two on each side). 5. Secure the board with two screws. 8. Carefully turn the disk drive frame over and place a hard disk drive on the HDD bay as shown.
Genie Book Size PC System 13 9. Secure the HDD to the frame using four screws (two on each side). Installing Disk Drives 10. Carefully re-install the CD- ROM drive frame to the main drive frame. I/O Plate Y ou may need to change the I/O plate on the chassis back panel if the I/O connectors on your motherboard do not match the existing plate.
14 Chapter 1: System Assemby Installing an IR-USB Module 1. Attach the L-type fastening bracket to the IR-USB module. 2. Install the IR-USB module to the USB slot on the front of the chassis.
Genie Book Size PC System 15 Installing the Motherboard A FlexA TX motherboard that measures 19.05cm (7.5in) x 19.05am (7.5in) fits into the Genie Book Size PC chassis. 1. Remove the riser card holder by lifting it up and unhooking it from the back panel frame.
16 Chapter 1: System Assemby Closing the Chassis 1. Replace the disk drive frame into the chassis as shown. 2. Check the drive frame tab on the front and make sure it fits in place. 3. Re-install the riser card holder by inserting the hooks (indicated by circles) into the holes on top of the slot frame.
Genie Book Size PC System 17 Closing the Chassis 5. Remove the CD-ROM drive cover . 6. Replace the front panel by inserting the two tabs underneath the panel into their corresponding holes on the bottom of the chassis. Push the panel in until the top holding tabs click in place.
18 Chapter 1: System Assemby Closing the Chassis 9. Ensure that the lock tab (indicated by circle) on the back panel goes through the hole at the back of the top cover .
19 Genie Book Size PC System This chapter tells how to install optional components and perform optional assembly procedures in the Genie Book Size PC System.
20 Chapter 2: Optional Procedures Changing the I/O Plate 1. Detach the I/O plate from the chassis by sliding it to the right. (CAUTION: Be careful when removing the I/O plate. The tabs that secure it are tight.) After removing the existing I/O plate, the back panel exposes an opening for the new I/O plate to fit your motherboard I/O connectors.
Genie Book Size PC System 21 Installing a PCI Expansion Card 1. Lift the card locking tab to access the PCI expansion slot. 2. Remove the expansion slot metal cover by sliding it to the right. 3. Install the riser card to the connector on the motherboard.
22 Chapter 2: Optional Procedures Installing a PCI Expansion Card 6. Make sure that the notched end of the card bracket fits the protruding tabs on the slot frame. 5. For card stability , make sure that the card bracket end goes into the cleft on the slot frame.
23 Genie Book Size PC System This chapter describes the dif ferent system placement options to allow you to maximize your working area and af ford you more convenience.
24 Chapter 3: System Placement Horizontal Placement Normally , you place the Genie Book PC system flat (horizontal) on the desk. The chassis comes with four rubber feet that prevent direct contact with the surface.
Genie Book Size PC System 25 Ver tical Placement Y ou may also place the chassis in a vertical position to save space. If you desire to position the system this way , you need to purchase an optional pair of foot stands and a plastic panel cover for the bottom of the system chassis.
26 Chapter 3: System Placement (This page was intentionally left blank.).
Ein wichtiger Punkt beim Kauf des Geräts Asus Genie (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Asus Genie noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Asus Genie - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Asus Genie reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Asus Genie erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Asus Genie besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Asus Genie verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Asus Genie. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Asus Genie gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
