Benutzeranleitung / Produktwartung OMG-PCI-DIO48 des Produzenten Omega Engineering
Zur Seite of 32
www .omega.com e-mail: info@omega.com U ser ’ s Guide OMG-PCI-DIO4 8 48 Channel Digital I/O Board Shop online at.
Servicing Nor th America: USA: One Omega Drive, P.O. Box 4047 ISO 9001 Certified Stamford CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1, Canada TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.
Contents INTRODUCTION .......................................................................................................... 1 O VERVIEW ..............................................................................................................
APPENDIX A - TROUBLE SHOOTING .................................................................. 23 APPENDIX B - HOW TO GET ASSISTANCE ...................................................... 24 APPENDIX C - SILK - SC REEN ..............................
Introduction and Installation OMG - PCI - DIO48 Page 1 Introduction Overview The OMG - PCI - DIO48 provides two 8255 mode 0 compatible ports providing four ei ght - bit ports and four four - bit ports. Each can be individually configured as inputs or outputs.
Introduction and Installation OMG - PCI - DIO48 Page 2 System Installation The OMG - PCI - DIO48 can be install ed in any of the PCI expansion slots. 1. Turn off PC power. Disconnect the power cord. 2. Remove the PC case cover. 3. Locate an available PCI slot and remove the blank metal slot cover.
Technical Description OMG - PCI - DIO48 Page 3 Technical Description The OMG - PCI - DIO48 provides 48 channels of digital I/O configurable as inputs or outputs, which can be utilized for PC based con.
Technical Description OMG - PCI - DIO48 Page 4 3 rd Party Software Support Third party software su pport for many HMI/MMI and other process control software is included on the product installation CD. For the most up to date information on third party software support, please visit http://www.
Technical Description OMG - PCI - DIO48 Page 5 Electrical Characteristics The table below provides the electrical characteristics of each Input/Output. Each port is buffered with a 74LS245 octal bi - directional transceiver. Each input is capable of sinking up to 24 mA, while each output can source up to 15 mA.
Technical Description OMG - PCI - DIO48 Page 6 Pull Ups Ten pin bussed resistor packs are installed to provide pull - ups to the input ports. These are installed on all ports. The pull - up resistor packs are rated at 10K ohms. Figure 2 below provides the bussed resistor and corresponding port.
Technical Description OMG - PCI - DIO48 Page 7 50 Pin Ribbon Pin Out Figure 3 - 50 Pin Ribbon Cable Pin Out Description Pin # Port A A0 47 A1 45 A2 43 A3 41 A4 39 A5 37 A6 35 A7 33 Port B B0 31 B1 29 .
Technical Description OMG - PCI - DIO48 Page 8 Application Programmers Interface (API) Most modern operating systems do not allow direct hardware access. The SeaIO driver and API have been included to provide control over the hardware in Windows and Linux environments.
Technical Description OMG - PCI - DIO48 Page 9 Port C relative addressing (when port C is split) The input and output nibbles will each be treated as individual four bit ports. Port Configuration: Each eight - bit port can be configured as inputs or outputs.
Notes Page OMG - PCI - DIO48 Page 10.
Technical Description OMG - PCI - DIO48 Page 11 Tables : API Por t/bit reference numbers for Absolute and Relative Addressing R = Read W = Write R/W = Read or Write Port API Port # Absolute Address (f.
Technical Description OMG - PCI - DIO48 Page 12 Absolute Address Port 1 Port 2 Absolut e bit Address Port - Bit Absolut e bit Address Port - Bit 0 A1 - 0 64 A2 - 0 1 A1 - 1 65 A2 - 1 2 A1 - 2 66 A2 - .
Technical Description OMG - PCI - DIO48 Page 13 The following tables are provided for the user in the event that he/she wishes to record their particular relative addressing setup, provided its constant. Print this page and fill in the tables starting in the top left corner of each and work from top to bottom, left to right.
Technical Description OMG - PCI - DIO48 Page 14 C1 - 6 C2 - 6 C1 - 7 C2 - 7 Figure 9 - (Print and fill in for your configuration) Direct Hardware Control In system s where the users program has direct access to the hardware (DOS) the tables below gives the mapping and functions that the 8005 provide.
Technical Description OMG - PCI - DIO48 Page 15 Interrupts Interrupts can be set up as shown in the tables on the next page ..
Technical Description OMG - PCI - DIO48 Page 16 Port C Port C is written and read to as a single eight bit port, but it has the ability to be configured as two four bit po rts. If both lower and upper nibbles are configure the same then no special considerations need to be made.
Notes Page OMG - PCI - DIO48 Page 17.
Technical Description OMG - PCI - DIO48 Page 18 Control Words n = control word for port1 or 2 I/O Configuration CWnD0 Port C1 lower nibble (bits 0 - 3) 1 = input 0 = output 1 on power up CWnD1 Port B1.
Technical Description OMG - PCI - DIO48 Page 19 Bit Set or Reset Port C n = port number CWnD0 1 = set to +5V 0 = Reset to GND CWnD4 0 or 1 (no effect) CWnD5 0 or 1 (no effect) CWnD6 0 or 1 (no effect).
Technical Description OMG - PCI - DIO48 Page 20 0 X X X 1 1 1 1 0F 7.
Technical Description OMG - PCI - DIO48 Page 21 Interrupt control When enabled interrupts are generated on A10 and A20 (Pin 47 on each 50 pin header), for this reason to use interrupts on a Port its A byte must be set as an input.
Specifications OMG - PCI - DIO48 Page 22 Specifications Environmental Specifications Specification Operating Storage Temperature Range 0º to 50º C (32º to 122º F) - 20 º to 70º C (- 4º to 158º F) Humidity Range 10 to 90% R.H. Non - Condensing 10 to 90% R.
Appendix A - Troubleshooting OMG - PCI - DIO48 Page 23 Appendix A - Troubleshooting Following these simple steps can eliminate most common pr oblems. Install software first . After installing the software then proceed to adding the hardware. This places the required installation files in the correct locations.
Appendix B - How To Get Assistance OMG - PCI - DIO48 Page 24 Appendix B - How To Get Assistance Please refer to Troubleshooting Guide prior to calling Technical Support. 1. Begin by reading through the Trouble Shooting Guide in Appendi x A. If assistance is still needed please see below.
A ppendix C - Silk - Screen OMG - PCI - DIO48 Page 25 Appendix C - Silk - Screen 4.2" 6.1".
Appendix D - Compliance Notices OMG - PCI - DIO48 Page 26 Appendix D - Compliance Notices Federal Communications Commission Statement FCC - This equipment has been tested and found to comply with the limits fo r Class A digital device, pursuant to Part 15 of the FCC Rules.
W ARRANTY / DISCLAIMER OME GA ENGINEERING, INC. war rants this unit to be free of defects in materials and workmanship for a period of 1 3 months from date of purc hase. OM E G A ’ s W ARRAN TY adds an additional one (1) month grace period to the normal one (1) year pr oduct warranty to cover handling and shipping time.
M 38 9 1 /0303 Where Do I Find Ever ything I Need for Pr ocess Measurement and Control? OM EGA…Of Course! Shop online at www .omega.com TEMPERA TURE Thermocouple, RTD & Thermistor Probes.
Ein wichtiger Punkt beim Kauf des Geräts Omega Engineering OMG-PCI-DIO48 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Omega Engineering OMG-PCI-DIO48 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Omega Engineering OMG-PCI-DIO48 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Omega Engineering OMG-PCI-DIO48 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Omega Engineering OMG-PCI-DIO48 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Omega Engineering OMG-PCI-DIO48 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Omega Engineering OMG-PCI-DIO48 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Omega Engineering OMG-PCI-DIO48. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Omega Engineering OMG-PCI-DIO48 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
