Benutzeranleitung / Produktwartung PT-024 des Produzenten Olympus
Zur Seite of 37
For the digital camera CAMEDIA X-3 ■ Thank you for buying the Underwater Case PT-024. ■ Please read this instruction manual carefully and use the product safely and correctly.
E-1 Introduction ● Unauthorized copying of this manual in part or in full, except for private use, is prohibited. Unauthorized reproduction is strictly prohibited. ● OLYMPUS CORPORATION shall not be responsible in any way for lost profits or any claims by third parties in case of any damage occurring from unsuitable use of this product.
E-2 1. Keep this product out of the reach of babies, infants, and children. There is the possibility of occurrence of the following types of accidents. Injury by dropping onto the body from a height. Injury from parts of the body getting caught in parts which open and close.
E-3 Batteries ● Please use one Olympus lithium ion rechargeable battery for cameras (LI-12B). ● Take care that the battery electrodes do not become wet. This may cause trouble or accidents. ● Carefully read the instruction manual for the camera about other cautions regarding batteries.
When water leakage occurs while this product is being used, repair of the camera housed in this product may become impossible. Please observe the following cautions for use.
E-5 Handling the Product ● Use or storage of the product at the following locations may cause defective operation, defects, trouble, damage, fire, internal clouding, or water leakage. Always avoid these locations. Locations reaching high temperatures such as those under direct sunlight, in an automobile, etc.
E-6 ● Do not perform operations other than specified in this instruction manual, do not remove or modify parts other than specified, and do not use parts other than specified. Any troubles in taking pictures or with the equipment resulting from the above actions shall be outside the guarantee.
E-7 Introduction ................................................................................E-1 Please read the following items before use ..............................E-1 For safe use ............................................................
E-8 Check the loading status. ........................................................E-18 Seal the Case. ........................................................................E-18 Installation and Removal of the LCD Hood ...........................
E-9 1. Preparations Check the contents of the package. Check that all accessories are in the box. Contact your dealer if accessories should be missing or damaged.
E-10 Names of the parts Note : The Case operation parts marked by ❈ corresponds to the operation parts of the digital camera. When the operation parts of the Case are operated, the corresponding functions of the digital camera will operate. For details of the functions, refer to the instruction manual for the digital camera.
E-11 Install the strap. Install the strap on the Case body. : Please install the strap correctly as shown above. OLYMPUS CORPORATION shall bear no responsibility for damage etc. caused by dropping the Case because of incorrect installation of the strap.
E-12 How to Press the Shutter When pressing the shutter lever, press it gently, so that there will be no movement of the camera. Note: • For detailed operation of the shutter, refer to the instruction manual for the digital camera.
E-13 2. Adv ance Check of the Case Advance test before use This Case has been the subject of thorough quality control for the parts during the manufacturing process and thorough function inspections during the assembly.
E-14 3. Install the digital camera. Check the digital camera. Check the digital camera before loading it in the Case. Battery Confirmation As the LCD monitor is used for picture confirmation while taking pictures under water, the battery life becomes short.
E-15 Loading in the Case Which digital cameras can be loaded? This product (PT-024) is exclusively used for the CAMEDIA X-3. Open the lens barrier. When the lens barrier of the digital camera is opened, the power is switched on. When the selected time has elapsed without any operation, the camera enters into sleep mode (standby condition).
E-16 Load the digital camera. Quietly load the digital camera into the Case, taking care that the projecting part of the zoom lever of the digital camera properly fits into the recessed part of the zoom lever of the Case.
E-17 Insertion of silica gel Before sealing the Case, insert the accessory silica gel bag for prevention of fogging between the bottom of the camera and the Case. Insert the bag with the glued longer side to the inside. :• Insert the silica gel all the way at the specified location and with the specified orientation.
E-18 Seal the Case. Check the loading status. :• Seal the Case by turning both buckle lock levers down in arrow direction. When one of the buckles is left open, the Case will not be sealed and water leakage will be caused.
E-19 Installation and Removal of the LCD Hood Installation Strongly push the mounting projections of the LCD hood as shown in the figure into the guides above and below the LCD monitor window. Removal Remove the mounting projections of the LCD hood from the guides above and below the LCD monitor window by widening the LCD hood.
E-20 Perform the final checks. Visual Inspection After sealing the Case, check the sealing part of front and rear lid visually to confirm that the O-ring is not twisted or out of the groove and that no foreign matter has been caught. Fit the lens cap onto the lens ring as shown in the figure.
E-21 Now everything is all right! Have a nice dive! Final Test The final test after loading the camera is explained below. This is the only way to eliminate worry about possible entry of water! Always perform this test. It can be performed easily in a water tank or a bathtub.
E-22 4. T aking Pictures Under Water How to Use the Hand Strap Pass your hand through the accessory hand strap and adjust the length with the stop button. Take pictures carefully. Confirm the picture on the LCD monitor. This Case uses the LCD monitor to confirm the picture.
E-23 5. Handling After Shooting Wipe off any waterdrop. After completing the shooting and returning to land, wipe off any waterdrop sticking to the Case. Use air or a soft cloth not leaving any fibers to thoroughly wipe any waterdrop etc. from the joint between the front and rear lid, the shutter lever, the palm grips, and the buckles.
E-24 Take out the digital camera. Open the case carefully, pull up the mode dial from the upper surface of the case to disengage it from the mode lever of the camera, and then remove the digital camera from the case. :• Always place the opened Case with the O-ring side facing up.
E-25 Wash the Case with pure water. After use, seal the Case again after taking out the camera and wash it sufficiently in pure water as soon as possible. After use in sea water, it is effective to immerse it for a fixed time in pure water to remove any salt.
E-26 6. Maintaining the W aterproof Function Remove the O-ring. Open the Case and remove the O-ring from the Case. Removal of the O-ring Insert the O-ring removal pick between the O-ring and the wall of the O-ring groove. Move the tip of the inserted pick under the O-ring.
E-27 :• When a mechanical pencil or a similar other sharp object is used to remove the O-ring or to clean the inside of the O-ring groove, the Case and the O-ring may be damaged and water leakage may be caused. • When the O-ring is checked with the fingertips, take care not to stretch the O-ring.
E-28 1 Install the O-ring. Confirm that no foreign matter is attached, apply a thin coat of the accessory grease to the O-ring, and fit the O-ring into the groove. At this time, confirm that the O-ring does not stick out from the groove. How to Apply Grease to the O-ring Apply the exclusive lubricant to each O-ring.
E-29 Replace consumable products. The O-ring is a consumable product. Independent of the number of times the Case is used, it is recommended that the O-ring should be replaced by a new one at least once a year. Deterioration of the O-ring is accelerated by the use conditions and the storage conditions.
E-30 7. Appendix Q & A on the use of the PT-024 Q1 : Which digital cameras can be used? A1 : The The PT-024 is only for the models X-3. Q2 : What cautions must be observed when loading the digital camera into the Case? A2 : Pay special attention to the following items when loading the camera into the Case.
E-31 (3) In case of the following handling with a camera loaded into the Case, trouble or breakage may be caused for the Case and/or the loaded camera. Always avoid such handling. (a) Hitting other objects (b) Dropping (c) Placing heavy objects on top of the Case (4) When the Case is not used for a long time, trouble from formation of mold etc.
E-32 of the Case and deterioration of the O-ring. Wipe the inside of the Case with a soft cloth not causing any fibers. Remove the O-ring, wipe off any salt, sand, dust, etc., and also clean the O-ring groove and the O-ring contact surface in the same way and then dry them.
E-33 (7) Throwing the Case from a boat into the water, jumping with the Case into the water, or other sudden application of strong forces onto the Case. When entering the water, hand the Case over quietly or avoid impacts in other ways. Q9 : What are the important points for O-ring maintenance? A9 : Please observe the following items.
E-34 Olympus defogging silica gel. • Do not use adhesive for repairs or other purposes. When repair is required, please contact a service station of our company or your dealer. Q11 : Please tell me about repairs. A11 : Please contact a service station of our company or your dealer, if repair should be necessary.
E-35 After-sale Service ● You will receive the guarantee card from your dealer. Please make sure that the dealer's name, the date of purchase, etc. have been entered. If they have not been entered, immediately ask your dealer to have them entered.
E-36 Specifications ❈ We reserve the right to change the external appearance and the specifications without notice. Available models Olympus digital camera CAMEDIA X-3 Pressure resistance Depth of u.
Ein wichtiger Punkt beim Kauf des Geräts Olympus PT-024 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Olympus PT-024 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Olympus PT-024 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Olympus PT-024 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Olympus PT-024 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Olympus PT-024 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Olympus PT-024 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Olympus PT-024. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Olympus PT-024 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
