Benutzeranleitung / Produktwartung MAUSB-10 des Produzenten Olympus
Zur Seite of 52
USB Reader/Writer REFERENCE MANU AL.
2 Introduction Thank you for purchasing our product. This product is exclusively for reading and writing data to an xD-Picture Card/SmartMedia. Y ou can transfer large amounts of data to and from the card quickly and easily using a computer equipped with a USB port (IBM PC/A T compatibles and Macintosh).
3 Contents Introduction .................................................................................................................................... 2 Contents ...................................................................................
4 What’ s inc luded Make sure all the following items are included. If any items are missing, inform the shop from where you purchased this product right away .
5 Before getting started System requirements Y our computer must conform to the following minimum standards in order to use it with the MAUSB-10. ● Compatible operating systems IBM PC/A T compatible.
6 W indows Macintosh [USB 1.1 compatible] T urn on computer . Place provided Installation CD-ROM in CD-ROM drive. *2 Install driver . *2 Restar t computer . *2 Connect to computer . Get started! *4 *1 : Windows 95/3.1/NT are not compatible. *2 : Y ou only need to perform this procedure before using the MAUSB-10 for the first time.
7 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <98/98 SE/Me ⽧ Install> T urn on your computer’s power (and connected devices) to start Windows.
8 <98/98 SE/Me ⽧ Install> 4. During installation, the window at right appears. * The installation time may vary , depending on your computer. 5. When the driver installation is complete, the window at right appears. Click the “Finish” button.
9 1. Double-click “My Computer”. <98/98 SE/Me ⽧ Install> 2. Right-c lic k “OL YMPUS”. Select “Open” from the pop-up menu. 4. Double-click “SETUP”. * The “OL YMPUS USB Reader/Writer InstallShield Wizard” window appears. Start installing by following “Install the device driver” ( 墌 p.
10 Operating the MAUSB-10 The operating procedures for the MAUSB-10 under Windows are described below . 1 Connecting to the computer <98/98 SE/Me ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
11 < 98/98 SE/Me ⽧ Operation > When the MAUSB-10 is connected to your computer , it is recognized as a “Removable Disk”. Y ou can see two “Removable Disk” icons by opening “My Computer” from the desktop.
12 2 Inserting a card <98/98 SE/Me ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
13 3 Removing a card <98/98 SE/Me ⽧ Operation> Close all software programs that are using data on the card (e.g. Explorer , graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
14 4 Copying files from a card <98/98 SE/Me ⽧ Operation> 4. Drag the file icons you want to copy and drop them onto the destination folder . * The process is the same as copying files from a floppy disk. * It is also possible to move files to another folder, erase files, or write data from another folder .
15 5 Formatting a card <98/98 SE/Me ⽧ Operation> 6 Disconnecting the MAUSB-10 <98/98 SE/Me ⽧ Operation> Close all software programs that are using the card (e. g. Explorer , graphics applications), then follow the steps below . 1. Make sure that the status lamp is NOT on.
16 How to uninstall the device driver <98/98 SE/Me> The device driver can be deleted if it is no longer needed. First make sure that the MAUSB-10 is disconnected from the computer’ s USB port, then follow the steps below . * On-screen displays or messages may vary depending on the version of Windows you are using.
17 How to uninstall the device driver (Cont.) <98/98 SE/Me> 4. A confirmation window appears. Click “OK”. 5. The “InstallShield Wizard” window appears. 6. The window at right appears. Click the “Finish” button. 7. The window at right appears.
18 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <2000/XP ⽧ Install> T urn on your computer’s power (and connected devices) to start Windows 2000/XP .
19 <2000/XP ⽧ Install> 4. During installation, the window at right appears. * The installation time may vary , depending on your computer. 5. When installation of the device driver is complete, the window at right appears. Click the “Finish” button.
20 1. Double-click “My Computer”. <2000/XP ⽧ Install> 2. Right-c lic k “OL YMPUS”. Select “Open” from the pop-up menu. 4. Double-click “SETUP”. * The “OL YMPUS USB Reader/Writer InstallShield Wizard” window appears. Start installing by following “Install the device driver” ( 墌 p.
21 Operating the MAUSB-10 The operating procedures for the MAUSB-10 under Windows 2000/XP are described below . 1 Connecting to the computer <2000/XP ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
22 <2000/XP ⽧ Operation> [Installing the hardware] 1. The “Found New Hardware Wizard” window appears when the MAUSB-10 is connected to Windows XP for the first time. Make sure that “Install the software automatically [Recommended]” is selected and click the “Next” button.
23 <2000/XP ⽧ Operation> 5. When the driver installation is complete, the window at right appears. Click the “Finish” button. 6. Confirm that two “Removable Disk” icons have been added by opening “My Computer” from the desktop. * The drive letters (e.
24 Before connecting After connecting MAUSB-10 * In this example, the Removable Disks are recognized as the J and K drive. The drive letters (e.g. “J:”, “K:”, etc.) used by your computer may dif fer depending on your computer and/or connected optional devices.
25 2 Inserting a card <2000/XP ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
26 3 Removing a card <2000/XP ⽧ Operation> Close all software programs that are using data on the card (e.g. Explorer , graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
27 4 Copying files from a card <2000/XP ⽧ Operation> 1. Start up your computer . 2. Double-click “My Computer” from the desktop. 3. T o view the contents of a card, double-clic k the corresponding “Removable Disk” icon.
28 5 Formatting a card <2000/XP ⽧ Operation> [Before formatting the card] • T o format a card, log on with the user name “Administrator”, or use a user name with administrator privileges. Otherwise, formatting the card will be impossible.
29 6 Disconnecting the MAUSB-10 <2000/XP ⽧ Operation> Close all software programs that are using data on the card (e.g. Explorer , graphics applications), then follow the steps below . 1. Make sure that the status lamp is NOT on. 2. Left-click the “Unplug or Eject Hardware” icon on the taskbar .
30 How to uninstall the device driver <2000/XP> The device driver can be deleted if it is no longer needed. First make sure that the MAUSB-10 is disconnected from the computer’ s USB port, then follow the steps below . * On-screen displays or messages may vary depending on the version of Windows you are using.
31 How to uninstall the device driver (Cont.) <2000/XP> 4. A confirmation window appears. Click “OK”. 5. The “InstallShield Wizard” window appears. The device driver is no longer installed. 6. The window at right appears. Click the “Finish” button.
32 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <Mac OS 8.6~9.2 ⽧ Install> T urn on your computer’s power (and connected devices) to start Mac OS.
33 3 Install the device driver <Mac OS 8.6~9.2 ⽧ Install> When using the MAUSB-10 for the first time, you must first install the device driver included on the provided CD-ROM. 3. Doub le-click the “Mac OS 9” folder . 4. Doub le-click “USB Reader_Writer”.
34 < Mac OS 8.6~9.2 ⽧ Install > 6. Click the “Restart” button. The device driver is now installed. (Remove the CD-ROM from the CD-ROM drive and store it in a safe place.) 5. When the Mac OS 8.x, 9.x installer starts up, the window at right appears.
35 Operating the MAUSB-10 The operating procedure for the MAUSB-10 under Mac OS is described below . 1 Connecting to the computer <Mac OS 8.6~9.2 ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
36 2 Inserting a card <Mac OS 8.6~9.2 ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
37 3 Removing a card <Mac OS 8.6~9.2 ⽧ Operation> Close all software programs that are using data on the card (e. g. graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
38 4 Copying files from a card <Mac OS 8.6~9.2 ⽧ Operation> 1. Insert a card in the MAUSB-10. * The status lamp blinks, then the card icon appears on the desktop. * The icon’s appearance may vary , depending on the card and the OS version. 2.
39 How to uninstall the device driver <Mac OS 8.6~9.2> The device driver can be deleted if it is no longer needed. First make sure that the MAUSB-10 is disconnected from the computer’s USB port, then follow the steps below . 1. From the desktop, double-click the hard disk icon.
40 How to install Also refer to your computer ’s user manual and the manuals for any optional devices you are using. 1 T ur n on the computer <Mac OS X ⽧ Install> T urn on your computer’s power (and connected devices) to start Mac OS.
41 3 Install the device driver <Mac OS X ⽧ Install> When using the MAUSB-10 for the first time, you must first install the device driver included on the provided CD-ROM. 1. Doub le-click the “OL YMPUS” icon. 2. Doub le-click the “MAUSB-10” folder .
42 < Mac OS X ⽧ Install > 6. Enter the administrator ’ s name and the pass- word, then click the “OK” button. 7. Click the “Continue” button. 8. Click the “Continue” button. 9. Select the disk to install on, then click the “Continue” button.
43 < Mac OS X ⽧ Install > 10. Click the “Install” (or “Upgrade”) button. 11. Click the “Continue Installation” button. 12. The window at right appears during the installation. 13. Click the “Restart” button. The device driver is now installed.
44 Operating the MAUSB-10 The operating procedure for the MAUSB-10 under Mac OS is described below . 1 Connecting to the computer <Mac OS X ⽧ Operation> After installing the device driver , connect the MAUSB-10’ s connector to the USB port on your computer .
45 2 Inserting a card <Mac OS X ⽧ Operation> 1. Make sure the MAUSB-10 is connected to the computer and insert the card into the corresponding card slot. [xD-Picture Card] Make sure the card is level and that the gold-colored contact area is facing down .
46 3 Removing a card <Mac OS X ⽧ Operation> Close all software programs that are using data on the card (e. g. graphics applications), then follow the steps below . Attention! If you do not follow the steps below , the data on the card(s) may be damaged.
47 4 Copying files from a card <Mac OS X ⽧ Operation> 1. Insert a card in the MAUSB-10. * The status lamp blinks, then the card icon appears on the desktop. * The icon’ s appearance may vary , depending on the card and the OS version. 2. Double-click the icon to display the files that you want to copy .
48 T roubleshooting Windows The status lamp (green) does not light. A “Found New Hardware Wizard” windo w appears when you connect the MAUSB-10. The MAUSB-10 doesn’t work even after installing the driver and connecting the MAUSB-10 to the computer .
49 T roubleshooting Macintosh The status lamp (green) does not light. No card icon(s) appears on the computer’ s screen. Y ou can read a card, but not write to it. Y ou cannot write with a SmartMedia. The error message “File Sharing is invalid.” appears.
50 Specifications * The specifications in this manual are subject to change without prior notice. * For the latest information, visit the OL YMPUS web site (http://www .olympus.com). * 1 Some cards with ID are not generally available for purchase. Consult your nearest SmartMedia dealer for details.
51 Glossary of T er ms A program used to operate or manage a peripheral device (printer , modem, digital camera, USB reader/writer , etc.). Without the proper driver installed, a peripheral device will not be recognized by the computer . A window that appears on the monitor when the computer requires user confirmation or instructions on what to do.
OL YMPUS OPTICAL CO ., L TD. VT398703.
Ein wichtiger Punkt beim Kauf des Geräts Olympus MAUSB-10 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Olympus MAUSB-10 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Olympus MAUSB-10 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Olympus MAUSB-10 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Olympus MAUSB-10 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Olympus MAUSB-10 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Olympus MAUSB-10 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Olympus MAUSB-10. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Olympus MAUSB-10 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
