Benutzeranleitung / Produktwartung AN/DC des Produzenten Nortel
Zur Seite of 150
Part No. 312410-A R ev 00 Novem ber 20 00 600 Tec hno log y Park Dr iv e Billeric a, MA 01821-4 130 Installing and Operating AN/DC and ANH-8/DC Systems.
ii 312410-A R ev 0 0 Cop yright © 2000 Nor tel Netw orks All rights reserved. Nov ember 2000. The in formatio n in this do cument is subje ct to c hange with out no tice.
3124 10-A Rev 00 iii EC Dec laration of Conf ormity This pr o duct co nforms ( or these pr oduc ts co nfor m) to the pr ovision s of Counci l Direct ive 89/336/E E C and 73/23/EEC.
iv 312410-A R ev 00 Canada Requirements Only (continued) Repai rs to cer t ified equipm ent sho ul d be coor dinat ed by a repre sentat ive design ated by the su pplier.
3124 10-A Rev 00 v FCC P ar t 68 Compliance Statement This equipm ent complie s with P a rt 68 of FCC Ru les. All dire ct c onnec tio ns to telep hone ne tw o r k line s mu st be mad e using sta ndard plugs and jacks com pliant with FCC P art 68. Please note the fo llowing: 1.
vi 312410-A R ev 00 Nor tel Netw orks NA Inc. Software License Agreement NO TICE: Pleas e carefully read this l i cense agre emen t befo re copying or usi n g the accom panying soft ware or installing the hardware unit with pre-enabled softwar e (each of which is referred to as “Software” in this Agreement).
3124 10-A Rev 00 vii for the se c urity o f its own data an d inform ation and for maint a ining adequat e procedure s apart from the S oftware to reconstru c t lost or alte red f iles, data, or p rograms.
.
312410-A R e v 00 ix Contents Preface Bef ore Y ou Begi n ........ .................... ............. ................... ............. ................... ............. ... xv ii T e xt C on ventions ........ .................... ............. ......
x 3124 10-A Re v 00 Connectin g a Manage ment Con sole or Modem ............. ............. ................... ............. . 1-12 Connectin g a T er minal Console .................. .................... ............ .................... ....... 1 -12 Connectin g a PC Cons ole .
312410-A R e v 00 xi Chapter 3 Star ting the AN/DC and ANH-8/DC About Sof tware Installation ...... ....... ............. ...... ....... ...... ....... ...... ............. ...... ....... ...... ... 3-1 Boot Opt ions .. ............. .................
xii 312410- A Rev 0 0 Appendix B Using Local Boot (the Quick-Start Procedure) Filling Ou t the Quick-Star t W or ksheets ............. .................... ............ .................... ........ B-2 Global Inf or mation Worksheet ........ ........
312410-A R e v 00 xiii Figures Figure 1-1. Mounti ng Hardware .. ...... ....... ...... ....... ...... ....... ...... ............. ...... ....... ...... ... 1-2 Figure 1-2. Conso le Cab les ........ ................... ............. ..................
xiv 312410- A Rev 0 0 Figure 2-17 . Connectin g a PC Console to the ANH-8/DC ......... ................... ............. . 2-23 Figure 2-18 . Connectin g a Modem to the A NH-8/DC .......... ............ .................... ....... 2 -25 Figure 2-19 .
312410-A R e v 00 xv Ta b l e s T abl e 1-1. Conso le P arameters ...... ............. .................... ............ .................... ....... 1 -13 T abl e 1-2. Modem P arameters .. ............. ...... ....... ...... ....... ...... ...... ...
xvi 312410- A Rev 0 0 T abl e D- 7. V .3 5 Interf ace (Order No . 7220) ......... ............. ................... ............. ........ D-5 T abl e D-8. X.21 Interface (Order No . 7 224) ......... ............. ................... ............. ...
312410-A R e v 00 xvii Preface Read th is guide for instruc tions on h ow to i nstall, st art, and opera t e Access Node or 8-Por t Access Node Hub models that hav e a singl e DC input s w itchi ng po wer supply , the AN™/DC and AN H™-8/DC.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems xvi ii 3124 10-A Re v 00 T ext Co n ven tio ns This gui de uses the fo llowi ng text con v entions: angle br ackets ( < >) Indicate that you choos e the te xt to enter bas ed on the descript ion inside t he bra c kets.
Prefac e 312410-A R ev 00 xix Acr o n yms This gui de uses the fo llowi ng acron yms: screen text Indicate s system out put, for ex ample, prompts and syst em m essag es. Example: Set Trap Monitor Filters vertic al line ( | ) Separates choices for command ke ywords and arg uments.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems xx 3124 10-A Re v 00 IEEE Institut e of Electrical and El ectronic Engi neers IP Internet Protocol ISDN Integ rated Services Digital Netw or k IS.
Prefac e 312410-A R ev 00 xxi Har d -Copy T echnical Ma nuals Y ou ca n print select ed technical manuals and release not es free, direct ly from the Int ernet . Go to the support.ba ynetworks. com/library/ tpubs/ URL. Find the p r oduct for which you need documentatio n.
.
312410-A R e v 00 1-1 Chap ter 1 Instal ling the AN/DC This chap ter descri bes ho w to install th e AN/DC. T op ics in this c hapte r incl ude • Prep aring for In stalla tio n • Insta lling the A.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-2 312410- A Re v 00 1. Inspe ct all it ems f or any shipping da m age. 2. Make sure that y our shipping package contains the f ollowing items : • Mounti ng hardware (Figure 1-1) . • Consol e /modem cable ki t (F igure 1-2 ) .
Insta lling the AN/ DC 312410-A R ev 00 1-3 Figure 1-2. Console Cabl es Suppl ying T ools and Equip ment Y ou may n eed items that are no t part of the ANH-8/DC ship ping accessor ies. Befo re ins tall ing th e AN H-8/D C hard ware , ensu re th a t you h ave all the cable s, tools, a nd other equi pment th at you n eed at your site .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-4 312410- A Re v 00 Service Console Y ou ca n attach a n optional VT -100 conso le or equi v al ent to th e AN/DC to monito r the res ults of s.
Insta lling the AN/ DC 312410-A R ev 00 1-5 Space Requirements The in stallat ion site must pr ovide a c ertain amount of free space around t he AN/D C to di ssi pate h eat . I nst all t he AN/D C in a spac e th at me et s the followin g spec ifica tions : • W idth: 19.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-6 312410- A Re v 00 Installing the AN/DC W i th a ll ca bling atta ched, you can i nstal l the AN/DC in an y of the fo llo w ing ways : • Posit ion the AN/ DC on a flat, st urdy surf ace. • Ins tall the AN /DC i n an el ectr oni c encl o sur e r ack .
Insta lling the AN/ DC 312410-A R ev 00 1-7 T o insta ll the AN/ D C in a rack: 1. Attach eac h flange bracke t to the AN/DC (Fig ure 1-3) as f ollo ws: a. Align the flange holes with the AN/DC mounting hole s. b. Insert a flange scr ew throug h each flange hole an d into the AN/DC.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-8 312410- A Re v 00 Figure 1-4. Installing the AN/DC in a Rack Y ou ca n now co nnect the netw ork cables to you r AN/DC. Go to the section “ Connecti ng Commun ications Cables ,” late r i n th is cha pt er .
Insta lling the AN/ DC 312410-A R ev 00 1-9 Mounting the AN/D C on a W all When mounting the AN/DC on a wa ll, keep the f ollow ing in mind : • Ma ke sure that th e wal l is at l east 3/8 in . (0. 9 6 cm) thic k , and is mad e of Sheetroc k or wood.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-10 312410- A Re v 00 Figure 1-5. Mounting t he AN/DC on a W all RUN BOOT DIAG POWER Rubber feet AN0005A.
Insta lling the AN/ DC 312410-A R ev 00 1-11 Connecting Co mm unic ations Cables T o connect ne twork cables to the back of the AN/DC: 1. Connect the appropri ate cables f or y our netwo rk conf iguration t o the communicati ons ports on the back of the AN/DC (F igure 1-6) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-12 312410- A Re v 00 Connect i ng a Managemen t Console or Mod em Use t he fro nt-pan el con sole port to connect an ASCII-based termin al, a persona l comput er terminal e mulator , or a mo dem to the AN/DC.
Insta lling the AN/ DC 312410-A R ev 00 1-13 Once you ha ve the appropri ate equipment , complete the f ollo wing step s: 1. P o wer on and c onf igure the consol e, using the para meters in Ta b l e 1 - 1 . Refer t o the console u ser manual for i nstructions .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-14 312410- A Re v 00 Figure 1-8. Connecting a T erminal Console 6. Atta ch t he 25-p in recep tac le conn ect o r on th e com bin ed cab le an d adapte r to t he termin al’ s host connect or .
Insta lling the AN/ DC 312410-A R ev 00 1-15 Once you ha ve the appropri ate equipment , complete the f ollo wing step s: 1. Inser t the 9 -pin r eceptacle end of the consol e cable i nto the CONSOLE port on the AN/DC ba ck panel (Figure 1-9 ) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-16 312410- A Re v 00 Connecting a Mo dem A mod em p rovides re mot e a ccess to the AN/D C for a networ k admi nistra tor . W e recomme nd that you conn ect a modem in cas e the AN/ DC experi ences syst em problems.
Insta lling the AN/ DC 312410-A R ev 00 1-17 2. P ower o f f t he modem. 3. Insert t he 9-pin re ceptacle end of t he modem cable into the back-panel CONSOLE port of the AN/DC (Fig ure 1-10) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-18 312410- A Re v 00 4. Insert t he 25-pin plug a t the other end of t he modem cable into the modem’ s RS-232 data communic ations por t . The modem is no w connected t o the AN/DC. Ne xt, connec t the po wer source as desc ribed in the follo wing sec tion.
Insta lling the AN/ DC 312410-A R ev 00 1-19 3. Strip 3/ 8 in. (10 mm) of insul ation from t he end of a #16 or # 18 A WG cabl e. 4. Inser t the s tripped end of the cable i nto the -VDC termi nal bloc k, the minus lead (Figure 1-12 ) . 5. T ighten the scr ew beneath the - VDC terminal block to e stablish the electr ical connecti on.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 1-20 312410- A Re v 00 9. Connect an e arth gro und to eithe r the leftmost termi nal block or to the gr ounding stud, locate d between the po wer switch and termi nal conn ect ors (Fig ure 1-13 ) .
312410-A R e v 00 2-1 Chap ter 2 Installing the ANH-8/DC This chap ter descri bes ho w to install th e ANH-8/DC. T op ics in this c hapte r incl ude: • Prep aring for In stalla tio n • Instal ling.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-2 312410- A Re v 00 V erifying Shipment Contents V eri fy that t he items you recei v e match the items in t he packing l ist attach ed to the shi pp ing co nt ain er . 1. Inspe ct all it ems f or shipping damage.
Installi ng the ANH- 8/DC 312410-A R ev 00 2-3 Figure 2-1. Accessories in the ANH-8/DC Shippi ng Container Suppl ying T ools and Equip ment Y ou may n eed items that are no t part of the ANH-8/DC ship ping accessor ies.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-4 312410- A Re v 00 Cables Unless t hey were s pecif ically o rdered, the Et hernet and sy nchrono us cables necessa ry for your ne twork conf iguratio n are not part of the ANH-8/DC ship ping accesso ries.
Installi ng the ANH- 8/DC 312410-A R ev 00 2-5 V erifying Site Requi rements V eri fy tha t your in stallation meet t he requ irement s liste d in th is section.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-6 312410- A Re v 00 En vironmental Requirements The ANH-8/DC in stallatio n site must meet the fol lo wing en vironmenta l spec ifica tions : .
Installi ng the ANH- 8/DC 312410-A R ev 00 2-7 Installing the AN H-8/DC in a Rack F or this procedu re, you need • F our #10 cag enut scre ws and washe rs (shipped with the ANH-8/ DC) • T wo fl an.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-8 312410- A Re v 00 Figure 2-3. Attac hing Flang e Brackets to Rack-Mount the ANH-8/DC 2. Align the flan ge brack et holes with the holes in the fr ont v ertica l supports of the ra ck (Figur e 2-4) .
Installi ng the ANH- 8/DC 312410-A R ev 00 2-9 Figure 2-4. Installing the ANH-8/DC in an Electronic Enc losure Rack 3. Insert a cagenut scr ew through each bracket hole and int o the corr esponding holes i n the ra ck. 4. T ighten each cagenut screw with a Phillips scr ewdriv er .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-10 312410- A Re v 00 Mounting the ANH -8/DC on a W all F or this procedu re, you need • T wo fl ange brack ets an d four # 6 roundh ead scr e.
Installi ng the ANH- 8/DC 312410-A R ev 00 2-11 Figure 2-6. Mounting the ANH-8/DC on a W all 3. Insert t wo to f our wall anchor screws thwr ough the hol e s in each fl ange brack et, and f asten each scr ew secur ely in t he wall.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-12 312410- A Re v 00 Connecting Co mm unic ations Cables Gather t he communicatio ns equipment and cab ling that yo u will attach t o the ANH-8/DC. If y ou do not ha ve the proper cable s , contact your n etwork admini strator or see the Cable Guide for Rout ers and BNX Platforms .
Installi ng the ANH- 8/DC 312410-A R ev 00 2-13 Connecting Ethe rnet Repeater P or t UTP Cables T o connect unshi elded twi sted-pair (U TP) cables to the front panel 10Base-T repeat er ports, at tach the UTP cabl es to the front-pane l RJ-45 connect ors (Eth ernet Repea ter Ports 1- 8), as sho wn in Figur e 2-8 .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-14 312410- A Re v 00 Figure 2-9. ANH-8/DC Fr ont-P anel MDI-X /MDI Switch Connecting t he ANH-8/DC to O ther Repeater s/H ubs Y ou can use Port.
Installi ng the ANH- 8/DC 312410-A R ev 00 2-15 When you c onf igure a netw ork with mu ltiple ANH- 8/DC (or other re peater/hub) systems, y ou must comply wit h the follo wing ru les: • Connect no m ore than four hubs. • Make sure that each U TP connecti on is not longer t han 100 mete rs (109.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-16 312410- A Re v 00 Figure 2-11. Linking Hubs Refer t o “10Base -T Repeater Ports (ANH- 8/DC only)” in Ap pendix C for more info rmation.
Installi ng the ANH- 8/DC 312410-A R ev 00 2-17 Connecting a Se cond Ethernet Interface UT P Cable Complete t hese steps t o connec t a UTP cabl e to the back p anel UTP-2 port. 1. Atta ch a U TP ca b le t o the b ack- pan el RJ- 45 co nnec tor ( Figure 2-12 ).
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-18 312410- A Re v 00 Connecting Synchr onous Cables Connec t one t o thre e synchrono us interf ace cabl es to the bac k of the ANH-8/DC: 1. Locate th e RS-232, RS-422, V .28, V .35, or X.2 1 interface cabl e.
Installi ng the ANH- 8/DC 312410-A R ev 00 2-19 Connecting an IS DN Cable Connect a n ISDN BRI cable to the back of the ANH-8/DC: 1. Plug the I SDN cable into the ISDN- BRI connector ( Figur e 2-14 ). Figure 2-14. Connecting an ISDN BRI Ca b l e 2. Connect the other end of t he cable to the ISDN communicatio ns de vice.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-20 312410- A Re v 00 Connect i ng a Managemen t Console or Mod em Use t he fro nt-pan el con sole port to connect an ASCII-based termin al, a persona l computer terminal emula tor , or a modem to the ANH-8 /DC.
Installi ng the ANH- 8/DC 312410-A R ev 00 2-21 4. Inser t the s cre w on the cable’ s connect or into the r eceptac le on th e adapte r’ s co nnector and t ighten the scr ew (Fi gure 2-15) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-22 312410- A Re v 00 6. Inser t the 9 -pin r eceptacle end of the consol e cable i nto the ANH-8/DC console p ort connect or .
Installi ng the ANH- 8/DC 312410-A R ev 00 2-23 Figure 2-17. Connecting a PC Cons ole to the ANH-8/DC 5. Attach th e 25-pin r eceptacl e end of the cable-plus-adapt er to the PC console c able’ s 25-pin plu g connector . 6. Connect the complete cable uni t to the co m munications port at the back of the PC ( Figure 2 -17) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-24 312410- A Re v 00 Comple te the following ste ps: 1. Conf igur e the modem, using t he parameters in T able 2-2 . Refe r to the mo d em use r manua l f or ins tr uctio ns. 2. P ower o f f t he modem.
Installi ng the ANH- 8/DC 312410-A R ev 00 2-25 Figure 2-18. Connecting a Modem to the ANH-8 /DC 4. Insert t he 25-pin plug a t the other end of t he modem cable into the modem’ s RS-232 data communic ations por t .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-26 312410- A Re v 00 Conne ct ing to th e DC P ower Source T o connect t he ANH-8/DC to the po wer source: 1. Ensure th at th e power s witch is in t he OFF ( 0) pos iti on (Figu r e 2 -19) . 2.
Installi ng the ANH- 8/DC 312410-A R ev 00 2-27 Figure 2-20. Attaching the ANH-8/DC P ower Input Cables 6. Strip 3/ 8 in. (10 mm) of insul ation from t he end of a #16 or # 18 A WG cabl e. 7. Inser t the stripped end of the cabl e into the R TN terminal block, the plus lead (Figur e 2-20) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 2-28 312410- A Re v 00 Figure 2-21. Attaching the ANH-8/DC Earth Ground Cab le 10. Bef ore qual if ied ser vice perso nnel connect the ANH-8/ DC to the power sour ce, verify that the powe r switch is OFF and that the ANH-8/DC has been pr operly gr ounded.
312410-A R e v 00 3-1 Chap ter 3 Star ting the AN /DC and ANH-8/DC The f irst time you start the AN/DC or ANH- 8/DC, you complete an i mportant softw are conf iguratio n process. Befo re you b egin the in itial s tart u p from a remo te site : 1. Coordinat e with your ne twor k admini strator .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-2 312410- A Re v 00 Y ou must complete an i niti al start up procedure to obta in the necessar y fil es and connect the AN/DC or ANH- 8/ DC to the netw or k. Ge tt ing a file o ver t he net work is calle d network booting, or ne tbooti ng .
Starting th e AN/DC and ANH-8/ DC 312410-A R ev 00 3-3 Installing the Flash Memor y Car d A PCMCIA Flash memor y card (Figure 3- 1) pro vides stor age cap ability for the non volat ile f ile system ( NVFS) in th e AN/DC and ANH-8/DC. When you r emo ve a form atted memory card, t he NVFS automat ically r e mov es access to the ca rd.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-4 312410- A Re v 00 1. P ositi on the card with the l abel facing up and the INSER T arr ow pointing toward the c ard rece ptacle.
Starting th e AN/DC and ANH-8/ DC 312410-A R ev 00 3-5 Figure 3-3. Inser ting a Flash Memory C ar d in the ANH-8/DC Card Receptacle Usin g EZ Ins tall T o use th e EZ Inst all fea ture: 1. Inst all the r outer and attached communi cation s equipmen t as des cribed in Chapter 1 (AN/DC) or Chapter 2 (ANH-8/DC).
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-6 312410- A Re v 00 Using Ne tboot, Dire cted Netboo t, or Local Bo ot Y ou us e a command interf ace to the r outer so ftware, th e Diagnostic Monitor , for Netbooti ng or Local Boot ing. (Y ou can also use the T echnician Interface o r Site Manager for t he Dire cted Ne tboot procedu re.
Starting th e AN/DC and ANH-8/ DC 312410-A R ev 00 3-7 Figure 3-4. Running Dia gnostic s 5. Bef or e diagnost ics ar e complete, si m ultaneously hold do wn the c ontr ol and c keys to bypass the automatic boot pr ocess. The AN Diagnos tics login pro m pt appears.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-8 312410- A Re v 00 Figure 3-5. Log gi ng In to the Diagnostic Monitor 6. T ype the f ollowing c omm and at the login p rompt and pr ess the Retu rn key: Manager Note that you must ty pe Manage r with an upper case “M.
Starting th e AN/DC and ANH-8/ DC 312410-A R ev 00 3-9 Continuing with Netboot 1. Contact y our network a dministrat or to verify that the netw ork is se t up f or the Netboot pr ocedu re. 2. Ask y our netw ork administr ator (o r r efe r to A ppendix A) f or the interf ace conf igurati on command to use in S t ep 3.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-10 312410- A Re v 00 Figure 3-7. V erifying the Interface Configuration 5. If the c onfigura tion inf ormation is cor rec t, continue to the next st ep. Otherwi se, r eenter t he corr ect ifconfig c om mand.
Starting th e AN/DC and ANH-8/ DC 312410-A R ev 00 3-11 Figure 3-8. N etboot 7. When y ou boot the r outer , its LEDs fla sh in a parti cular order . T o interpre t the LED sequence and t rou ble shoo t an y potenti al pr oble m s, re fe r to Chapte r 4.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-12 312410- A Re v 00 Continuing with Directed Netb oot Before yo u can use the Dire cted Netboo t procedure, you mus t hav e already use d the ifconfig command (as described i n the pre vious sec tion) to confi gure the interf ace from whi ch you plan to use Direct ed Netboot.
Starting th e AN/DC and ANH-8/ DC 312410-A R ev 00 3-13 4. T yp e the following comm a nd and pr ess the Retur n key to v erify the conf igurati on that y ou specif ied in Step 3 (Figur e 3-10) : getcfg Figure 3-10.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-14 312410- A Re v 00 Figure 3-11. Directed Netboot After t he router re boots, it gets a configuration file from a TFTP server and load s the so ftw are imag e from the local f ile system. The ro uter sta rts bridging an d routing tr af fic.
Starting th e AN/DC and ANH-8/ DC 312410-A R ev 00 3-15 Continuing with Local Boot Y ou need to use both the Diagnos tic Mo nitor and the T echnicia n Inter fa ce to loc al boot the AN. Before starting the Lo cal Boot procedur e, ask your network admini strator f or assistan ce in comple ting the Quic k-Start wo rksheets in Appendix B.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-16 312410- A Re v 00 Figure 3-12. Local Boot 4. When y ou boot the r outer , its LEDs fla sh in a parti cular order . T o inter pret t he LED sequence and troubl eshoot any p otential pr oblems, refer to C h apte r 4; then return t o S tep 5 .
Starting th e AN/DC and ANH-8/ DC 312410-A R ev 00 3-17 Figure 3-13. Logging In to the T echnician Interface and Mounting a Vo l u m e 6. T ype the f ollowing c omm and and pr ess th e Retur n key to begi n the Quick-Star t pr ocedure: run install.bat 7.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 3-18 312410- A Re v 00 8. When the T echnic ian Interf ace pro mpt re appears, type the follo wing command and pr ess the Ret urn key to exit the T echnicia n Interfac e: logout Once the install sc ript compl etes, the r outer starts b ridging and rout ing traf fi c.
312410-A R e v 00 4-1 Chap ter 4 Operating the AN /D C and ANH-8/DC This chap te r descr i bes • Ensu ring a Succ ess ful I n stal latio n (usin g the f ront-pan el LEDs) • Checki ng the statu s o.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-2 312410- A Re v 00 Ensuri ng a Succe ssfu l Inst allation After co nnecting the route r to the n etwork, you c an ensure a su ccessf ul instal lation by che cking the LEDs on the front panel. Figure 4- 1 sho ws the front-pan el LEDs on an AN/DC.
Operati ng the AN/DC and ANH-8/ DC 312410-A R ev 00 4-3 When po wer is suppli ed to the router , the follo wing LED seque nce should occ ur: • The PO WER LED lights and re main s on. • R UN, BOO T , and DIA G (or F A UL T for ANH) LEDs li ght for approxima tely 1 sec ond, the n turn of f, indicati ng that the rout er is functio ning.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-4 312410- A Re v 00 AN/DC LED Desc riptions LEDs on the A N/DC fr ont and bac k panels pro vide informatio n about ho w the AN/DC is oper ating. The foll owi ng sections d escribe t he AN/DC front- and back-pan el LEDs.
Operati ng the AN/DC and ANH-8/ DC 312410-A R ev 00 4-5 Bac k-P anel LEDs The LEDs on t he AN/DC back-panel dif fer dependin g on the AN/DC model that you ha v e. Ta b l e 4 - 2 descr ibes al l of the av ailable AN/DC ba ck-panel LEDs. These LEDs ind icate t he status of the AN/DC’ s network connections.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-6 312410- A Re v 00 ANH-8 /DC LED D escri ptions LEDs on the ANH-8/DC fr ont and bac k panels pr ovid e informat ion about ho w the ANH-8/DC is opera t ing. Fr o nt-P anel LEDs Figure 4- 2 sho w n earlier i llustra tes the t hree sets of status LEDs on the ANH front panel.
Operati ng the AN/DC and ANH-8/ DC 312410-A R ev 00 4-7 Bac k-P anel LEDs Figure 4- 3 ill ustrat es the back-pa nel LEDs for th e ISDN and Second Ethernet options . These LEDs are vi sible after i nstalling ei ther an ISDN BR I nterf ace or Second Ethern et Inter face upgr ade modul e.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-8 312410- A Re v 00 Ta b l e 4 - 4 describes th e back -panel LEDs . P o weri ng On an d Of f The DC po wer switch allo ws yo u to rest art the router without ha ving to disconne ct the p o wer suppl y wires.
Operati ng the AN/DC and ANH-8/ DC 312410-A R ev 00 4-9 Figure 4-4. AN/DC P ower Switch Figure 4-5. ANH-8/DC P ower Switch 2. V erify that ai r i s f lo w i ng by placing y o ur hand to the s ide of the f an v ents. T o po wer of f, press the switc h to the Of f posit ion (0); toggle the swi tch up.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-10 312410- A Re v 00 Resetting the AN/DC or ANH-8/DC Yo u can use the Reset b ut ton to r eboot th e rou ter hardw ar e without c ycling po wer , as fol lows: •T o warm-boot t he router (no diagnosti c tests ru n), press the Reset b utton for less t han 3 seconds.
Operati ng the AN/DC and ANH-8/ DC 312410-A R ev 00 4-11 AN/DC Reset Sw itch On the AN/DC, t he Reset but ton is located on the back panel of the AN/DC (Figu re 4-6 ) . Labeled “RST ,” it resides b etween the console port and the LED labele d “RLSD2.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-12 312410- A Re v 00 Remo ving a Flash Memor y Car d When you remo ve a formatt ed memory car d, the NVFS automat ically r emov es access t o the card. When you insert and f ormat a card or insert an alr eady formatt ed card, the NVFS a utomati cally pro vides access .
Operati ng the AN/DC and ANH-8/ DC 312410-A R ev 00 4-13 Pr otecting Memor y Card Files Nort el Netwo rks ships each memo ry ca rd with it s read -wri te prot ect sw i tch in the unpro tected po sition (Figu re 4-10) .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems 4-14 312410- A Re v 00.
312410-A R e v 00 A-1 Append ix A Configuring Net boot and Directed Netboot Y ou c an use th e foll owing c ommand s to c onfigure th e AN /D C or AN H-8 /D C fo r Netboot a nd Directed Net boot: • Use th e i fconfig co mman d to c on figure th e r out e r’ s initia l IP in terface to the netw ork.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems A-2 312410- A Re v 00 Configuring a Sy nchr ono us IP Interface for Netbooting T o Netboot, you must firs t confi gure the route r’ s ini tial .
Config uring Ne tboot and Di rected Netboo t 312410-A R ev 00 A-3 Configuring an E thernet Interface for Netbooting T o conf igure an Eth ernet inter face f or Netbootin g, use the follo wing command .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems A-4 312410- A Re v 00 Enab ling and Disab ling Interfaces with if config T o enable or disabl e an interf ace for th e Netb oot process, u se the.
Config uring Ne tboot and Di rected Netboo t 312410-A R ev 00 A-5 T able A-3. The bconfig Command Options Opt ion Des cr ipti on imag e Spe cifie s infor mat io n a bou t the s oftwar e imag e. config S pecifies inf ormation ab out the configura tion file .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems A-6 312410- A Re v 00.
312410-A R e v 00 B-1 Append ix B Using Local Boot (the Quic k-Star t Pr ocedure) Y ou c an loc al boo t the AN/ DC or ANH-8/ DC us in g t he Site Manager Qui ck- Sta rt procedur e expla i ned in this appendix. Y ou need t his informat ion to complete t he procedur e in “Continuing w ith Loca l Boot” on page 3-15 .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-2 312410- A Re v 00 Filli n g Out th e Quick-Star t W or ksheet s The in stall.ba t scri pt pro vides man y options fo r conf iguring t he router on a netw ork. Use th e follo wing work sheets to or ganize yo ur network information.
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R ev 00 B-3 Global Inf ormation W orksheet This sec tion contain s the prompts a nd poss ible opti ons relati ng to all AN/ANH synch ron ous conf igurations. Wri te your selectio n i n t he “ Y our Response” column.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-4 312410- A Re v 00 3 Enter IP address in dotted decimal notation: Enter t he IP ad dress f or the COM inte rface. Enter the subnetwork mask in dotted decimal notation: En ter the subnet work mask f or the COM int erf ace IP address .
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R ev 00 B-5 Router Pr otoc ol W o rksheets This sec tion contain s requested in formati on and possibl e options relating t o the routing protocol cho i ces on the Gl obal Informat ion W orkshee t.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-6 312410- A Re v 00 Enter OSPF MTU size selection [1]: 1. Default 2. Ethe r net size (N or t el Net wor ks Series 5 com patib le) 3. User d efined MT U Enter OSPF interface type selection [1]: 1.
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R ev 00 B-7 Enter decimal value i n seconds for Poll Inte rval [20]: (F or NB MA onl y) Enter the l argest n umber of seco nds allo wed bet ween Hell o pack ets tha t the route r sends to an inactiv e NBMA ne ighbor .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-8 312410- A Re v 00 Static Rout e to Site Mana g er W orksheet Requested Inf ormation Options Y our Information Destination Network [0.0.0.0]: En ter the g atew a y address of the des tinat ion ne twor k.
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R ev 00 B-9 Wide Area Protocol W orksh eets This sec tion contain s requested in formati on and possibl e options relating t o wide area pr otocol choic es on th e Global I nformation W orksheet.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-10 312410- A Re v 00 Enter address field l ength: 2. T wo Bytes 3. Three Bytes 4. F o ur Byt es Enter DLCI number [30 ]: (F o r DLCMI None , LMI Switc h, Anne x D Switch , and Anne x A Switch onl y) Enter the P ermanent Vir tual Circ uit (PVC) num ber .
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R ev 00 B-11 Enable the LQR (Link Quality Reporting) Protocol? (y/n) [n]: y(es) n(o) Note: Link Qual ity M onitoring on a Nor tel Networ k s Ser ies 5 ro uter is not com patible with th is f eature .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-12 312410- A Re v 00 Using th e Quick-Star t Comma nds Refe r to the com m an ds in Ta b l e B - 1 when quick-st arting the AN/DC or ANH-8/DC.
Using Lo cal Boot (the Qui ck-St art Proce dure) 312410-A R ev 00 B-13 Runn ing the Q uic k-S tart Script After you ent er run install.bat , the AN/DC or ANH-8/DC prog re sse s thr oug h the Quic k-Sta r t scr ipt as f ollows: 1. The scrip t begins pr ompt ing you for the ini ti al Globa l W orksheet inf ormat i on.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems B-14 312410- A Re v 00.
312410-A R e v 00 C-1 Append ix C T ec hnical Specificati ons This appendi x pro vides • AN/DC Phy sical Specif icatio ns • ANH-8/DC Phys ical Specif ications • Po wer Supply Specif ications •.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-2 3124 10-A Re v 00 P o wer Sup ply Specifica tions Specif ications for both the AN/DC AN and A NH-8/DC p o wer suppl y: • Nominal in put vol.
Technic al Spec ific ations 312410-A R ev 00 C-3 T able C-1. AN/DC Network Interfaces Network Interface D escrip tion Ethe r net and Second Et her net Suppo r ts the Ethernet and IEEE 802.3 stand ards that p rovide L AN conne cti vity . The Ethe rnet interf aces on an AN /DC i nc lud e a 10 Bas e-T (UTP) a nd an 802.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-4 3124 10-A Re v 00 ANH-8/D C Har d wa re Communications Options Ev ery ANH-8/DC i ncludes • 9 Ethe rnet L AN repeater ports (1 A UI and 8 UT.
Technic al Spec ific ations 312410-A R ev 00 C-5 Conne ct or Pinouts This sec tion lists pinout s for the AN/DC and ANH-8/ DC connectors: • Attac h ment Un it Inte rface (A UI) P orts • 10Base-T Re peater Ports (ANH- 8/DC only) • Synchronou s Interf aces • ISDN BRI Port s • Local Cons ole Connections T able C-2.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-6 3124 10-A Re v 00 Attachment Unit Interface (A UI) P or ts The AN/DC back p anel and ANH-8/DC fron t panel co ntains a standa rd 802.3 A UI DB-15 re cept ac le conne ct or wi th a sl ide loc k fo r co nnec ti on t o the A UI.
Technic al Spec ific ations 312410-A R ev 00 C-7 10Base-T Repe ater P or ts (ANH -8/DC only) The eight Ethernet 10Base- T repeate r port RJ- 45 connectors on t he ANH-8/DC front pane l prov i de UTP s uppo rt .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-8 3124 10-A Re v 00 Synchr onous Interfaces The AN/DC and ANH-8 /DC support tw o synchron ous interfa ces, label ed COM1 and COM2. Syste m s with a Third Synchronous I nterface or ISDN BRI upgrade module support a third synchr onous port.
Technic al Spec ific ations 312410-A R ev 00 C-9 T able C-5. Synchr onous P or t Pin Assi gnments Pin Assignm ent Pin No. Signal Name Pin No. Signal Name 1 FGND 23 D CD- 2 SD+ 24 ST - 3 RD+ 25 R T - 4.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-10 3124 10-A Re v 00 ISDN BRI P or ts The AN/DC and ANH-8/ DC support t he BRI standar d for ISDN usi ng an opti onal ISDN/BRI modul e. Th e integ rat ed ISDN BRI fu nct io nal it y al l o ws you to conn ect direct ly to the ISDN ne twork, as op posed to connec ting via a terminal ad apter .
Technic al Spec ific ations 312410-A R ev 00 C-11 The AN/DC and ANH-8 /DC shipping package includes the Ord er No. 110310 conso le/modem kit for connect ing de vices to the Console por t. • T o connect a m odem to the Consol e port, use the Or der No.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems C-12 3124 10-A Re v 00.
312410-A R e v 00 D-1 Append ix D Requi rements f or Eur opean Ope ra t io n This appe ndix provide s information r equired f or operating th e AN/DC and ANH-8/DC in Europe . ANH-8/D C Safety Status T ables D- 1 , D-2 , and D-3 li st the safe ty sta tus of i nterconnecti on poin ts to the connecti on of other equi pment.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-2 3124 10-A Re v 00 AN/DC S af ety Status Ta b l e D - 4 list s the safety st atus of int erconnect ion points t o the c onnection of other e quipment. Safety Status (Third Synchr onou s Int erface Modu le) Order Nos.
Requi rements for Euro pean Ope ratio n 312410-A R ev 00 D-3 Synchr on ous Ca bling Require ments Refe r to Figure D-1 throug h Figure D-3 and Ta b l e D - 6 thro ugh Ta b l e D - 8 fo r synch ron ous int er f a ce cabl in g infor mation. Note the fo ll o wing co mplia nce re quire men ts : • V .
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-4 3124 10-A Re v 00 Figure D -2. Cable 7220 (V .35 Com pliant) 9 D ata Carrier Detect+ 8 Data Ca rrier Detect 10 S end T iming + 15 S end Ti mi.
Requi rements for Euro pean Ope ratio n 312410-A R ev 00 D-5 T able D-7. V . 35 Inter face (Order No. 7220) Nortel Netw orks T erminatio n Remote T ermination Pin Signal Pin Signal 38 VSD+ P Send Data.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-6 3124 10-A Re v 00 Figure D-3. Cable 722 4 (X.21 Compliant) T able D -8. X.21 Interface (O r de r No.
Requi rements for Euro pean Ope ratio n 312410-A R ev 00 D-7 ISDN BRI Re qu iremen ts The IS DN BRI module (Ord er Nos. AE0004006, AE001 1013, and AE0011019 for the ANH-8/ DC) and ISDN BRI upgrade modul e (Order Nos.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-8 3124 10-A Re v 00 ISDN BRI Cleara nces and Creepage Dista nces The clea rances and cr eepage dista nces ( sho wn as X and Y , respecti vely ,.
Requi rements for Euro pean Ope ratio n 312410-A R ev 00 D-9 The cree page distance s apply to th e normal of fice en vironment. Whe n the local en vironment wit hin the host c hassis is s ubject to c.
Installi ng and Op erating AN/DC and ANH-8/DC S ystems D-10 3124 10-A Re v 00 ISDN BRI Connec tor Pinouts Ta b l e D - 1 2 lists the ISDN conne ctor pinouts.
312410-A R e v 00 Index- 1 Numbers 10Base-T ports (ANH-8/DC), 2-13, 2-17, C-7 A AN/DC conne c t ing to the po wer sour ce, 1- 18 dimensi ons, C -1 installing in an ele ct ronic e ncl os ure rack, 1- 6 on a fl at su rface, 1-6 on a wall, 1- 9 LEDs.
Index-2 312410- A Re v 00 straigh t-th r ough, 2-1 4, C-7 supply ing, 2-4 sync hronou s, C-8 cagenut s, for elect ronic encl osure rac k, 1-7 clocki ng, A-2 cold bo ot, 4-10 collisio n dete ction AN/D.
312410-A R ev 00 Index-3 electroni c enclosur e rack installing AN/DC in, 1-6 installing ANH-8/DC in, 2-7 physica l specif ications, 1-4 en viron mental sp e cif ications AN/DC, 1-5 ANH-8/DC, 2-6 Ethe.
Index-4 312410- A Re v 00 Power , 4 -6 Run, 4-6 RX (Recei ve), 4 -8 TX (T ransmit), 4-8 LEDs, AN/DC PO WER, 4-4 linking ANH-8/DCs, 2-14 Local Boot attach ing a console, 1-12 , 2-20 definiti on, 3-2 re.
312410-A R ev 00 Index-5 R repeater ports (ANH-8/DC) 10Base- T , 2- 13, 2-1 7, C-7 resetting, 4-10 RIP worksheet, B-5 RLSD 1 (R ecei ved Line Signa l Dete ction 1) L ED, 4-5 RLSD 2 (R ecei ved Line Si.
Index-6 312410- A Re v 00 W wa ll-mounting AN/DC, 1-9 ANH-8/DC, 2-10 wa rm boot , 4-10 X X.21 conn ections , C-8.
Ein wichtiger Punkt beim Kauf des Geräts Nortel AN/DC (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Nortel AN/DC noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Nortel AN/DC - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Nortel AN/DC reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Nortel AN/DC erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Nortel AN/DC besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Nortel AN/DC verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Nortel AN/DC. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Nortel AN/DC gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
