Benutzeranleitung / Produktwartung 35mm des Produzenten Nikon
Zur Seite of 52
- 1 - User ’ s Manual 35mm Film Scanner COOLSCAN II Standard Model and Internal-Mount Model Contents 1. Overview 1.1 Features 1.2 Operating Environment for Standar d Model 2. Before Operation 2.1 Inspection 2.2 Components 2.3 Notes on Use 2.4 Cleaning the Unit 3.
- 2 - 5. Setting Up the Internal-mount Model 5.1 Before Installing 5.2 Installing the Internal-mount Model 5.3 Setting the SCSI ID 5.4 T erminating the SCSI Chain 5.5 SCSI Cables Used with Internal Scanners 5.6 Connecting to the Computer SCSI 5.7 Setting Up a SCSI Chain with the Scanner 6.
- 3 - Cautions • The reproduction of all or part of this manual without our permission is prohibited. • The information contained in this manual is subject to change without notice. • We have made every effort to produce a perfect manual, but should you find any mistakes, we would be grateful if you would kindly let us know.
- 4 - F ederal Communications Commission (FCC) Radio F r equency Interfer ence Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- 5 - Cautions for Saf ety In order to use the COOLSCAN II safely and correctly, and to prevent problems, pay careful attention to the following points: • Use an AC power supply of 50/60Hz and a voltage of from 100V–240V. Be sure to use a power cord rated for the appropriate voltage.
- 6 - • When plugging in or unplugging the power cord, be sure to touch only the plug. • Do not extend the power cord of the product, as this may cause malfunction. This can cause breakage and failure. • Do not connect or remove peripheral equipment while the power switch is on.
- 7 - • Avoid harsh substances such as alcohol, benzine, thinner, or pesticides, as failure, fire, and/or an electrical shock may result. • Do not subject the unit to any strong shocks. This can cause breakage and failure. • Do not place heavy objects on the unit.
- 8 - • Do not pull or bend the SCSI cable. This can cause the cable to malfunction. 5 If Y ou Notice An ything Abnormal If unusual noise, odor or smoke occurs, switch the Unit off immediately and disconnect the power cord and the SCSI cable. Contact your retailer or Nikon sales representative in your country.
- 9 - Storag e and Operating Locations Proper storage will ensure the long life of the Unit. In order to avoid internal dust while being stored, it is recommended that an appropriate cover be used on the Unit.
- 10 - • The Unit may be subjected to excessive vibration. • The Unit is placed on tilted surface. • The Unit is exposed to electrical noise and interference from other equipment nearby. Leave sufficient space around the unit to ensure that the ventilation slots are not blocked.
- 11 - Cautions for Operation • Don't carry the Unit or film while scanning. This can cause breakage and failure. • When moving the scanning stage, don't touch or unmount the film holder. This can cause breakage and failure. • Don't use a slide mount more than 3mm thick.
- 12 - Notice concerning pr ohibition of cop ying or repr oduction Note that simply being in possession of material which has been copied or reproduced by means of a scanner may be punishable by law.
- 13 - 1. Ov er view Thank you for purchasing the Nikon 35mm Film Scanner COOLSCAN II. This manual describes the procedures for unpacking, setting up, and connecting the scanner, with emphasis on hardware use and precautions. Please read the sections appropriate for the scanner you are using, to ensure proper operation.
- 14 - 1.2 Operating En vir onment for Standard Model Leave extra space around and above the unit to ensure smooth operation. Please refer to the drawings below for the amount of space to be provided. If possible, place a suitable cover over the unit to avoid dust accumulating when it is not being used.
- 15 - 2. Bef ore Operation 2.1 Inspection Inspect the package to see whether any damage has occurred during shipment. If there is any damage to the package, please contact your retailer directly and do not unpack the unit. 2.2 Components When you open the package, check whether all the items are present.
- 16 - Internal-mount Model The following items are included with your COOLSCAN II Internal-mount model package. Guide rail (1) Main Body (1) SCSI 50-pin flat cable (1) FH-2 Strip Film Holder (1) Inte.
- 17 - 2.3 Notes on Use • Don’t use a slide mount neither less than 1.1mm nor more than 3.0mm thick. If the slide mount is not flat on its surface, you may feel some roughness when mounting or unmounting the slide. • Don’t force the slide-mount or strip film holder into or out of the unit if it does not move smoothly.
- 18 - 3. P ar ts Identification 3.1 Main Unit Standard Model SCSI Connectors: For SCSI cable connection. No difference between IN and OUT. SCSI ID switch: Sets the SCSI ID number. Numbers 0 to 7 are shown and valid. AC Inlet: Connect to the AC power source with the power cord provided.
- 19 - Internal-mount Model Film Slot: The film holder is inserted here. Status display LED: Shows the scanner status. SCSI Connector: For SCSI connection. Configuration DIP switch: Sets the SCSI ID number. Power Connector: Connect to the power source.
- 20 - 3.2 Status Displa y LED The display LED is located on the front panel and shows the scanner status. Steady illumination: Lights when power is supplied (READY status). Blinking (about once every 1.5 seconds): Blinks slowly during operation (BUSY status).
- 21 - 4. Setting Up the Standar d Model 4.1 Bef ore Connection Before connecting the cables, confirm that all devices, including the computer system and the COOLSCAN II, are turned off. For an IBM PC/AT or compatible in which a SCSI board has not been installed, install a SCSI board as explained in the manual supplied with the board.
- 22 - 4.2 Connecting the P o w er Cord Before connecting the power cord, confirm that the unit’s power switch is in the off position. Insert the female end of the supplied power cord into the AC inlet located on the rear panel, then insert the plug into the AC power outlet.
- 23 - 4.3 Connecting the SCSI Cable Before connecting the SCSI cable, confirm that all SCSI devices, including the computer system, have been turned off. Connect the unit to the computer using the SCSI cable. After attaching the connector, be sure to lock it in place.
- 24 - SCSI Chain Connection with Other De vices If Scanner is connected at the end of the SCSI chain: • Connect the 50-pin full pitch connector of the SCSI cable to the SCSI connector located on the rear panel of the unit, and insert the other end to the SCSI connector of other SCSI device.
- 25 - Remarks • The maximum number of SCSI devices that can be connected to one computer is eight including the CPU. When using with a host computer with a built-in SCSI hard disk or built-in CD-ROM, note that SCSI ID numbers have been pre-assigned for the host CPU and the SCSI devices.
- 26 - 4.4 Setting the SCSI ID The SCSI ID for the COOLSCAN II is set at “5” when the unit is shipped. If other SCSI devices are connected to your computer, make sure that the SCSI ID for the COOLSCAN II is different from those assigned to other SCSI devices.
- 27 - 5. Setting Up the Internal-mount Model The internal-mount scanner is easy to install, following the procedure described below. 5.1 Befor e Installing The internal-mount scanner is shown below. Note that the front of the internal-mount model is identical to that of the standard model.
- 28 - Both sides of the internal-mount scanner are identical as shown below. Note the set of two tapped holes on each side. One set of holes on each side of the scanner will be used for the rails as shown in this figure.
- 29 - Installing the guide rails Different computers have their own special requirements for mounting devices in an internal drive bay. In most cases, a pair of guide rails are screwed to the sides of the scanner to enable it to be slid into the drive bay.
- 30 - The computer drive bay has one or two metal stops screwed into the tapped holes on the sides of each half-height drive slot. These should be loosened to allow them to either be removed or to hang freely so they do not block the drive bay receptacles for the guide rails.
- 31 - Installing the internal-mount scanner in the driv e ba y Step 1—Connect the SCSI cable to the scanner Connect one end of the flat 50-pin SCSI cable to the 50-pin SCSI connector on the rear of the internal-mount scanner as shown below. Insure that Pin 1 of the cable is aligned with Pin 1 of the scanner.
- 32 - Step 4—Feed the computer power connector Feed the computer power 4-pin connector, through the drive bay from the inside as far as it will extend out through the drive bay. Connect the cords with each 12V DC or 5V DC connector. Note: When you establish a ground, connect a grounding cable (not provided) to the GND screw.
- 33 - Step 6—Connect the power connector Connect the 4-pin power connector of the computer to the 4- pin power connector of the scanner. Note that both connectors are keyed so that one side of the connector is beveled. Be careful to insure that the beveled edges are properly aligned.
- 34 - Determining which ID to use If the scanner is the only SCSI device that will be connected to the SCSI bus, there is no need to change the SCSI ID from the preset value. If the scanner must share the SCSI bus with one or more other peripherals, it is necessary to insure that no two peripherals have the same ID.
- 35 - Setting the SCSI ID on the Internal Scanner The SCSI ID is set by a set of DIP switches on the back of the internal-mount scanner as shown below. In most cases, these DIP switches will not be changed. If it is necessary to change the default SCSI ID, change the position of the DIP switches to the proper SCSI ID.
- 36 - 5.4 T erminating the SCSI Chain The SCSI chain is an electrical bus connecting two or more devices. It is critical that this bus be correctly terminated for the SCSI peripherals to work properly. Termination is an electronics term that applies to the impedance found at both ends of the bus.
- 37 - Remarks • When connecting the terminator to the scanner, insert it straight, and correctly aligned with the locator key, taking care not to bend the pins. • When removing the terminator from the scanner, pull it straight out, taking care not to bend the pins.
- 38 - 5.6 Connecting to the Computer SCSI The SCSI port on the computer is a connector located either inside the computer or on the rear panel of the computer. There are three basic types of SCSI connectors dealt with in this manual: the 50-pin internal connector, standard 25-pin DB25 type connector, and 50-pin external Centronics connector.
- 39 - Care must be exercised when inserting and removing these 50- pin connectors. The connecting pins are rather fragile. Follow the rules below when handling these connectors. 1. Never force the connector in and out. 2. Make sure that the connectors are properly aligned before inserting.
- 40 - Typically, the scanner will be the only peripheral on the internal SCSI bus. If this is the case, the 50-pin cable provided will work. In some cases, the scanner will not be the only peripheral on the internal SCSI bus. When this occurs, the SCSI cable provided will not work.
- 41 - 6. Operation 6.1 T urning on the P o w er Turn the COOLSCAN II on first, the other SCSI devices next, and the host computer last. If your scanner is the internal- mount model, you need not turn the COOLSCAN II on. After turning the power on, the LED will begin to blink to indicate scanner initialization.
- 42 - 6.2 Film Inser tion The COOLSCAN II can scan different types of 35mm positive/ negative monochrome/color images. In addition, it can scan a film strip of up to 6 frames or single film ‘chips’. Inser tion of Mounted slides The COOLSCAN II can scan mounted slides as they are.
- 43 - The standard orientation of a mounted portrait or landscape slide is shown below. If the top and bottom are reversed, the image can be flipped using software.
- 44 - Inser tion of Film Strip Insert the film strip into the attached film holder FH-2, and then insert the holder into the film slot of the front panel of the unit. Step 1 Remove the cover latch and open the upper holder. Be sure the word Nikon, printed on the adaptor cover of the upper holder is facing upward.
- 45 - Step 3 Align each image of the strip film with an aperture in the lower holder. Step 4 Close the upper holder, aligning both ends of the upper holder and the lower holder. Fasten the latches at both ends of the holder after securing the adaptor cover and fastening the cover latch.
- 46 - Step 5 Align the image to be read with either of the two apertures in the silver-colored adaptor frame. Insert the film holder in the film slot of the front panel in the scanner , with placing the aperture through which the image is to be read toward the slot.
- 47 - Step 6 Insert the film holder until it touches the back of the stage and is aligned with the edge of film slot, as shown. Remarks • Do not force the film holder into the scanner. • Though the film holder is made of plastic, it will be damaged if film is forced into it.
- 48 - 7. T r oubleshooting If something unusual should occur, please check the following items before you conclude that there is a unit failure. For more details, refer to the Troubleshooting section of the software manual. Scanner cannot turned on. • Is the Power cord connected? Connect the Power cord.
- 49 - Appendix: Specifications Reading system/Optics Film type: 35mm film (color or monochrome, negative or positive) Reading resolution: 2,592 x 3,888 pixels Reading area: 24.3 x 36.5mm Effective area: 23.4 x 35.4mm (with strip film holder) Light source: RGB 3-color LED Film holder: No holder needed for mounted slides.
- 50 - Others Power requirements: Standard model: AC 100 - 240V, 50/60Hz, 0.3 - 0.2A Internal-mount model: DC 5V, 1.5A, DC 12V, 1.2A Panel indicators: READY, BUSY and ERROR states indicated by LED Temperature: 50˚F – 95˚F (10˚C – 35˚C) Humidity: 20% – 85% (with no condensation) Dimensions: Standard model: 6.
- 51 - Index A AC inlet 18 Adaptor cover 44 Adaptor snap 20 B Before use 15 C Cleaning the unit 17 Components 15 Configuration DIP switch 19 Connecting the power cord 22 Connecting the SCSI cable 23 C.
- 52 - ERKLÄRUNG ÜBER EG-NORMENGERECHTHEIT Wir Name: Nikon UK Limited Anschrift: Nikon House, 380 Richmond Road, Kingston, Surrey KT2 5PR, UK erklären hiermit, daß das folgende Produkt Produktbezeichnung: Nikon 35mm Filmscanner LS-20E/LS-20I Name des Herstellers: Nikon Corporation Anschrift des Herstellers: Fuji Bldg.
Ein wichtiger Punkt beim Kauf des Geräts Nikon 35mm (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Nikon 35mm noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Nikon 35mm - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Nikon 35mm reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Nikon 35mm erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Nikon 35mm besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Nikon 35mm verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Nikon 35mm. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Nikon 35mm gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
