Benutzeranleitung / Produktwartung EM1300 des Produzenten Newland
Zur Seite of 136
NLS-EM1300 1D Barcode Scanning Engine Integration Guide V ersion 1.0.
nlscan.com Page 2 V ersion Description Date Pre-release Initial release 26-08-2009 V ersion 1.0 Support as from EM1300 fi rmware V ersion 1.13.7 and higher .
Disclaimer © 1999-2008 by Newland Auto-ID T ech. Co., Ltd, All rights reserved. No part of this publication may be reproduced, transmitted, or used in any form or by any means, electrical or mechanical, without prior written permission from Newland Auto-ID.
nlscan.com Page I 请更换节标题 T able of Contents Content About this guide Introduction ................................................................................................................................................. 1 Chapter Description .
nlscan.com Page II T able of Contents EM1300 Development T ools Introduction ................................................................................................................................................ 19 EM1300 Evaluation Kit, EVK3000&1300 .
nlscan.com Page III T able of Contents Disable or Enable User Pre fi x ............................................................................................................. 48 Program User Pre fi x ...........................................
nlscan.com Page IV T able of Contents ISBN .......................................................................................................................................................... 67 Load Factory Default .............................
nlscan.com Page V T able of Contents Matrix 25 Code ID .............................................................................................................................. 86 Check Digit ......................................................
nlscan.com Page VI T able of Contents MSI-Plessey .............................................................................................................................................. 11 2 Load Factory Default ................................
nlscan.com Page 1 About this guide Introduction This NLS-EM1300 ( “ EM1300 ” ) Scan Engine Integration Guide provides general instructions for OEM integration. Chapter Description About EM1300: The chapter of About EM1300 gives a brief description of the EM1300.
nlscan.com Page 2 About this guide Newland Auto-ID Support Center If you have a problem with your equipment, contact the Newland Support Center in your region. Before call- ing, have the model number , serial number , and several of your barcodes at hand.
nlscan.com Page 3 About EM1300 Introduction EM1300 is an embedded barcode reading engine. Its gray scale CCD image capturer and the Newland patented UIMG, a Computerized Image Recognition System, ensure the fast scanning and decoding accuracy on different barcode media such as paper , plastic card, and metal surface.
nlscan.com Page 4 About EM1300 Get Familiar W ith EM1300 Unpacking Remove EM1300 and accessories from the package. Check for missing parts and inspect for damage. EM1300 is packed in anti-static bag. Please handle accordingly . Outline of EM1300 The outline of EM1300 is shown in Figure 1.
nlscan.com Page 5 About EM1300 EM1300 Decode Zone 42 ° 90mm Code 39(5mil) 195mm 0 100 200 300 400 500 50mm Code 39(10mil) 325mm 60mm EAN-13(10mil) 265mm 65mm EAN-13(15mil) 350mm 30mm Code 128(10mil) .
nlscan.com Page 6 About EM1300 EM1300 Overall Speci fi cations Performance Interface TTL232 Image Sensor CCD Resoluing 2500 Scan Rate up to 300 scans/sec Decode Rate 200 decodes/sec (default) Symbologies Code128, EAN-13, EAN-8, Code39, UPC-A, UPC-E, Codabar , Interleaved 2 of 5, ISBN/ISSN, Code 93, etc.
nlscan.com Page 7 Introduction Mechanical Interface This section describes theMechanical Interface..
nlscan.com Page 8 Mechanical Interface Dimensions of EM1300 Unit EM1300 Front V iew Following fi gures show the dimensions of EM1300. The fi gure 2 is EM1300 Front V iew . EM1300 Front V iew Figure 2. EM1300 Left Side V iew The Figure 3 is EM1300 Left Side V iew .
nlscan.com Page 9 Mechanical Interface Interface Interface Socket EM1300 uses a 12-pins fl ex cable socket to interface with external device (Host), such as EVK3000&1300, the EM1300 Evaluation Kit. Figure 5 below shows the socket. For reference purpose, the EM1300 Evaluation Kit uses a connector to connect the fl ex cable.
nlscan.com Page 10 Mechanical Interface Interface Pin T ype I/O* Description PIN 1 Flash Download I Operation Mode Control: Flash Download Mode – Level Low when engine is » powered on; Normal Mode – otherwise. » If useres don ’ t need the function, it can be not connected(N/C).
nlscan.com Page 1 1 Mechanical Interface Interface Schematic of Interface Socket Unit : mm 0 5 . 11 6 . 0 2 . 5 6 8 . 4 3 8 . 5. 5 2 . 0.
nlscan.com Page 12 Mechanical Interface Interface Interface Flexible Cable Speci fi cations The interface fl exible cable is designed by Newland Auto-ID.
nlscan.com Page 13 Mechanical Interface Housing Design Considerations Housing Structure The housing for the Engine should make sure that no pressure should be put on the Engine. There should have suf fi cient space for the fl exible cable and stress release of the cable should also be considered.
nlscan.com Page 14 Electrical Interface Introduction This section describes the electrical speci fi cations of the interface signals..
nlscan.com Page 15 Electrical Interface Interface Signal levels The table below lists the interface input and output level voltage ranges Signal T ype V oltage Level V oltage Range Input High 2.4V - 3.6V Low -0.3V - 0.6V Output High 2.9V - 3.3V Low 0V - 0.
nlscan.com Page 16 Electrical Interface Input signals When the T rigger line is pull low for 10 ms, the Engine starts a read. The Engine keeps reading until a successful reading, a timeout or the line is high. After a successful reading, the line must go high in order to make another read.
nlscan.com Page 17 Electrical Interface Output Signals Here are the descriptions of the output signals, such as Beeper , LED and inter-character timeout. They can be used to detect the status of the scanning, message uploading and the state of the Engine.
nlscan.com Page 18 Electrical Interface Output Signals A Sample Schematic of LED Circuit Here is the LED circuit used in the evaluation board, EVK3000&1300. R1 3 1K R1 4 100 K DGN D D5 GL ED R1 7 10 R DL ED DV 3. 3V Q4 2N 390 6 A Sample Schematic of Beeper Circuit Here is a beeper circuit used in the evaluation board, EVK3000&1300.
nlscan.com Page 19 EM1300 Development T ools Introduction Sections below list some EM1300 development tools. A brief introduction to each tool is included.
nlscan.com Page 20 EM1300 Development T ools EM1300 Evaluation Kit, EVK3000&1300 Here is a brief introduction to the EM1300 Evaluation Kit, EVK3000&1300. The layout of the EVK3000&1300 circuit board is shown in fi gure below . The board contains beeper , LED and trigger button.
nlscan.com Page 21 Introduction There are 2 ways to program (con fi gure) the Engine, Code Programming and Command Programming. Code Programming The Engine reads a set of specially encoded barcodes to program options and features.
nlscan.com Page 22 General Programming General Programming T ools Code Programming ON Code Programming OFF Programming Notation Th i s is th e n ot at i on t o d is a bl e t he C o de P r og ra m mi ng .
nlscan.com Page 23 General Programming General Programming T ools Code Programming ON Code Programming OFF Code Programming Re a d th e “ Co d e Pr o gr am m in g O N ” b a rc od e t o a ct iv a te “ C od e P ro gr a m- mi n g ” f u nc ti o n.
nlscan.com Page 24 General Programming Command Programming Commands under RS232 connection mean using 0x20-0x7D ( the displayable characters ) to express all commands information. Con fi guration State 1 、 The engine should be in con fi guration state when programming functions under RS232 connection.
nlscan.com Page 25 General Programming Command Programming 3 、 F lo w C ha rt Non-Con fi guration State Con fi guration State Host sends “ $$$$ ” and receives “ @@@@ ” 5 seconds timeout .
nlscan.com Page 26 General Programming General Programming T ools Code Programming ON Code Programming OFF Default Factory Default Read “ Load All Factory Default ” to reset all parameters to factory default.
nlscan.com Page 27 General Programming General Programming T ools Code Programming ON Code Programming OFF W orking Mode Shut Down 1 【 Pro CMD : 99900100 】 Deep Sleep 2 【 Pro CMD : 99900101 .
nlscan.com Page 28 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Hand-held Mode Factory Default, scan engine will begin to scan when triggered. And when it scans successfully or the trigger is released, the engine will stop scanning.
nlscan.com Page 29 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Auto Mode First program the engine, then trigger it, the engine will start to scan. After a scan, the engine will not stop but start a new one automatically until another trigger.
nlscan.com Page 30 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Interval Mode After programming, the engine will start interval scan without trigger . The interval between two scans is fi xed whether the scan is successful or not.
nlscan.com Page 31 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Sensor Mode After programming, the engine will start to sense the environment without trigger . After a scan, it will stop and keep sensing to wait another illumination changing.
nlscan.com Page 32 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Continuous Mode 【 Pro CMD : 999001 14 】 Continuous Mode After programming, the engine will be in continuous mode without trigger .
nlscan.com Page 33 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Delayed Sensor Mode After programming, the engine will start to sense the environment without trigger . There will be a delay before a scan.
nlscan.com Page 34 General Programming General Programming T ools Code Programming ON Code Programming OFF Reading Mode Command T riggered Mode After programming, when HR100 receives trigger sweep command from terminal ( e.g. PC ) , then the device is begun working.
nlscan.com Page 35 General Programming General Programming T ools Code Programming ON Code Programming OFF Security Level Security Level 1 【 Pro CMD : 99900120 】 Security Level 2 【 Pro CMD :.
nlscan.com Page 36 General Programming General Programming T ools Code Programming ON Code Programming OFF Beeper No Beeper Output 【 Pro CMD : 99900130 】 High Frequency & Loud V olume 【 Pr.
nlscan.com Page 37 General Programming General Programming T ools Code Programming ON Code Programming OFF Others Start/Stop Analog Trigger Start Analog T rigger 【 Pro CMD : 99900035 】 StopAnalo.
nlscan.com Page 38 Query Command Introduction After reading interrelated programming barcodes, the engine will feed information needed back to the Host to achieve the purpose of query .
nlscan.com Page 39 Communication Programming Introduction Under TTL232 connection the engine and the Host use the same communication parameters: baud rate, parity check, data bits select and stop bits select.
nlscan.com Page 40 Serial Port Programming Communication Setup Under TTL232 connection, the engine and the Host should set communication baud rate to the same to keep normal communication. Baud rate is the bits transmitted per second (8 bits per bytes).
nlscan.com Page 41 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Check ** No Check 【 Pro CMD : 99902120 】 Odd Check .
nlscan.com Page 42 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Stop Bit ** 1 Stop Bit 【 Pro CMD : 99902131 】 2 Sto.
nlscan.com Page 43 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Flow Control ** No Flow Control 【 Pro CMD : 99902140 .
nlscan.com Page 44 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming Data Bit ** 8 Data Bit 【 Pro CMD : 99902150 】 8 Dat.
nlscan.com Page 45 Communication Programming Communication Programming T ools Code Programming ON Code Programming OFF Serial Port Programming 7 Data Bit 【 Pro CMD : 99902151 】 7 Data Bit, Even .
nlscan.com Page 46 Data Format Introduction 1D barcodes could contain digits, letters and symbols, etc. 2D barcodes could contain more data, such as Chinese characters and other multi-byte characters.
nlscan.com Page 47 Data Format Data Format T ools Code Programming ON Code Programming OFF Pr e fi x S eq ue n ce s CodeID+User Pre fi x+AIMID 【 Pro CMD : 99904010 】 User Pre fi x+CodeID+AIMID.
nlscan.com Page 48 Data Format Data Format T ools Code Programming ON Code Programming OFF User Pre fi x User Pre fi x is added before barcode message. For example, if the user pre fi x is “ AB ” and the barcode message is “ 123 ” , the Host receives “ AB123 ” .
nlscan.com Page 49 Data Format Data Format T ools Code Programming ON Code Programming OFF AIM Pre fi x AIM (Automatic Identi fi cation Manufactures) de fi nes AIM pre fi x for many standard barcode formats. The engine will add the identi fi er before the barcodes.
nlscan.com Page 50 Data Format Data Format T ools Code Programming ON Code Programming OFF Code ID Pre fi x Besides AIM pre fi x, Code ID pre fi x can be used to denote barcode format and can be customized. The Code ID pre fi x MUST be one (1) or two(2) visible English letters, capital or small, only .
nlscan.com Page 51 Data Format Data Format T ools Code Programming ON Code Programming OFF Program “ AGE ” as user suf fi x (The hex of “ AGE ” are0x41/0x47/0x45): 1. Read “ Code Programming ON ” 2. Read “ Program User Suf fi x ” 3. Read “ 4,1,4,7,4,5 ” in order 4.
nlscan.com Page 52 Data Format Data Format T ools Code Programming ON Code Programming OFF T erminal Program a W indows OS general line feed and carrage returen as terminal 1. Read “ Code Programming ON ” 2. Read “ Program T erminal ” 3. Read “ Set T erminal as 0x0D,0x0A and Enable Sending ” 4.
nlscan.com Page 53 Introduction Each type of barcode has its unique attribute. W ith the programming code, the engine will adjust to the changes of these attributes. Disabling reading of the symbols which do not apply will improve reading performance.
nlscan.com Page 54 Symbols T ools Code Programming ON Code Programming OFF Code 128 Lo a d Fa c to ry De fa u lt Load Code 128 Factory Default 【 Pro CMD : 99910000 】 Enable/Disable Code 128 Enab.
nlscan.com Page 55 Symbols T ools Code Programming ON Code Programming OFF Code 128 1D bar code Message Length should not exceed 255 bytes. If Max Message Length is less than Min Message Length, it means the engine will only support barcodes of the two lengths.
nlscan.com Page 56 Symbols T ools Code Programming ON Code Programming OFF UCC/EAN-128 Lo a d Fa c to ry De fa u lt Load UCC/EAN-128 Factory Default 【 P r o CM D : 99910100 】 Enable/Disable UCC/EAN-128 When the engine can not read UCC/EAN-128, please read “ Enable UCC/EAN-128 ” and try again.
nlscan.com Page 57 Symbols T ools Code Programming ON Code Programming OFF UCC/EAN-128 1D bar code Message Length should not exceed 255 bytes. If Max Message Length is less than Min Message Length, it means the engine will only support barcodes of the two lengths.
nlscan.com Page 58 Symbols T ools Code Programming ON Code Programming OFF AIM 128 Load Factory Default Load AIM 128 Factory Default 【 P r o CM D : 99910200 】 Enable/Disable AIM 128 When the engine can not read AIM 128, please read “ Enable AIM 128 ” and try again.
nlscan.com Page 59 Symbols T ools Code Programming ON Code Programming OFF AIM 128 1D bar code Message Length should not exceed 255 bytes. If Max Message Length is less than Min Message Length, it means the engine will only support barcodes of the two lengths.
nlscan.com Page 60 Symbols T ools Code Programming ON Code Programming OFF EAN-8 Load Factory Default Load EAN-8 Factory Default 【 Pro CMD : 99910400 】 Enable/Disable EAN-8 Enable EAN-8 【 P r .
nlscan.com Page 61 Symbols T ools Code Programming ON Code Programming OFF EAN-8 2 D ig it s A dd en d a Co d e 2 D ig it s A dd en d a Co d e is the one to the right of an ordinary code.
nlscan.com Page 62 Symbols T ools Code Programming ON Code Programming OFF EAN-8 EA N -8 e x pa nd to E A N- 13 “ Do Not Expand to EAN-13 “ — keep original type and digits, do not expand. “ Expand to EAN-13 by Adding Leading 0s “ — expand to EAN-13 but keep code type.
nlscan.com Page 63 Symbols T ools Code Programming ON Code Programming OFF EAN-13 Lo a d Fa c to ry De fa u lt Load EAN-13 Factory Default 【 Pro CMD : 99910500 】 Di s ab le / En ab l e EA N -1 3.
nlscan.com Page 64 Symbols T ools Code Programming ON Code Programming OFF EAN-13 Ch e ck D i gi t T ransmit Check 【 Pro CMD : 99910504 】 Do Not T ransmit Check 【 Pro CMD : 99910503 】 EA N -1 3 is fi xed 13 digits barcode and the last digit is check digit.
nlscan.com Page 65 Symbols T ools Code Programming ON Code Programming OFF 5 Digits Addenda Code 2 Digits Addenda Code 5 Digits Addenda Code is the one to the right of an ordinary code. 2 Digits Addenda Code is the one to the right of an ordinary code.
nlscan.com Page 66 Symbols T ools Code Programming ON Code Programming OFF ISSN Load Factory Default Load ISSN Factory Default 【 Pro CMD : 99910600 】 Enable/Disable ISSN Enable ISSN 【 P r o CM.
nlscan.com Page 67 Symbols T ools Code Programming ON Code Programming OFF ISBN Load Factory Default Load ISBN Factory Default 【 Pro CMD : 99910700 】 Enable/Disable ISBN Enable ISBN 【 P r o CM D : 99910702 】 Disable ISBN 【 P r o CM D : 99910701 】 When the engine can not read ISBN, please read “ Enable ISBN ” and try again.
nlscan.com Page 68 Symbols T ools Code Programming ON Code Programming OFF ISBN ISBN Code ID Code ID Setting 【 Pro CMD : 99910705 】 Example of setting ISBN Code ID to “ p ” (0x70) 1. Read Enable Code Programming barcode. 2. Read ISSN Code ID Setting barcode.
nlscan.com Page 69 Symbols T ools Code Programming ON Code Programming OFF UPC-E Lo a d Fa c to ry De fa u lt Load UPC-E Factory Default 【 P r o CM D : 99911000 】 Di s ab le / En ab l e UP C -E .
nlscan.com Page 70 Symbols T ools Code Programming ON Code Programming OFF UPC-E Check Digit UP C -E is fi xed 8 digits barcode and the last digit is check digit. Check digit is a value caculated from all digits. It is used for checking if the all 8 digits are right.
nlscan.com Page 71 Symbols T ools Code Programming ON Code Programming OFF 5 Digits Addenda Code 2 Digits Addenda Code Disable 5 Digits Addenda Code 【 Pro CMD : 9991 1010 】 Enable 5 Digits Adden.
nlscan.com Page 72 Symbols T ools Code Programming ON Code Programming OFF UPC-E Tra ns m it D e fa ul t “ 0 ” The fi rst byte of UPC-E is default to “ 0 ” .
nlscan.com Page 73 Symbols T ools Code Programming ON Code Programming OFF UPC-A Load Factory Default Load UPC-A Factory Default 【 P r o CM D : 99911 100 】 Disable/Enable UPC-A When the engine can not read UPC-A, please read “ Enable UPC-A ” and try again.
nlscan.com Page 74 Symbols T ools Code Programming ON Code Programming OFF UPC-A Check Digit UPC-A is fi xed 13 digits barcode and the last digit is check digit. Check digit is a value caculated from all digits. It is used for checking if the all 13 digits are right.
nlscan.com Page 75 Symbols T ools Code Programming ON Code Programming OFF 5 Digits Addenda Code 2 Digits Addenda Code Disable 5 Digits Addenda Code 【 Pro CMD : 9991 11 10 】 Enable 5 Digits Adde.
nlscan.com Page 76 Symbols T ools Code Programming ON Code Programming OFF Interleaved 2 of 5 Load Factory Default Load Interleaved 2 of 5 Factory Default 【 Pro CMD : 9991 1200 】 Disable/Enable .
nlscan.com Page 77 Symbols T ools Code Programming ON Code Programming OFF Interleaved 2 of 5 Check Digit Interleaved 2 of 5 may include Check Digit (not compulsory) following its barcode messages. If included, it could be the last digit. It veri fi es the barcode message.
nlscan.com Page 78 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Interleaved 2 of 5. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 79 Symbols T ools Code Programming ON Code Programming OFF ITF-6 ITF-6 is a fi xed length 6 bytes Interleaved 2 of 5 barcode with check digit. Wh e n e na b le d , I T F- 6 p r ec e de s 6 - by t e I nt e rl e av e d 2 o f 5 b ar c od e .
nlscan.com Page 80 Symbols T ools Code Programming ON Code Programming OFF ITF-14 ITF-14 is a fi xed length of 14 bytes Interleaved 2 of 5 barcode with Check digit. By factory default, it is disabled. Wh e n e na b le d , I T F- 1 4 p re c ed e s 1 4- b yt e I n te r le a ve d 2 o f 5 b a rc o de .
nlscan.com Page 81 Symbols T ools Code Programming ON Code Programming OFF Deutshe14 Load Factory Default Load Deutshe14 Factory Default Deutshe14 Factory Default Factory Default 【 Pro CMD : 9991 .
nlscan.com Page 82 Symbols T ools Code Programming ON Code Programming OFF Deutshe12 Load Factory Default Load Deutshe12 Factory Default Deutshe12 Factory Default Factory Default 【 Pro CMD : 9991 1600 】 Disable/Enable Deutshe12 When the engine can not read Deutshe12, please read “ Enable Deutshe12 ” and try again.
nlscan.com Page 83 Symbols T ools Code Programming ON Code Programming OFF COOP25 ( Japanese Matrix 25 ) Load Factory Default Load COOP25 Factory Default 【 P r o CM D : 99911700 】 Enable/ Disable COOP25 When the engine can not read COOP25, please read “ Enable COOP25 ” and try again.
nlscan.com Page 84 Symbols T ools Code Programming ON Code Programming OFF COOP25 ( Japanese Matrix 25 ) Check Digit COOP25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It veri fi es the barcode message.
nlscan.com Page 85 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of COOP25. The engine will send an error beep, if the decoded data length does not match the valid length. COOP25 Message Length is de fi ned by “ Min.
nlscan.com Page 86 Symbols T ools Code Programming ON Code Programming OFF Matrix 25( European Matrix 25) Lo a d Fa c to ry De fa u lt Load Matrix 25 Factory Default 【 P r o C MD : 99912000 】 Enable/ Disable Matrix 25 When the engine can not read Matrix 25, please read “ Enable Matrix 25 ” and try again.
nlscan.com Page 87 Symbols T ools Code Programming ON Code Programming OFF Matrix 25( European Matrix 25) Check Digit Matrix 25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It veri fi es the barcode message.
nlscan.com Page 88 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Matrix 25. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 89 Symbols T ools Code Programming ON Code Programming OFF Industrial 25 Load Factory Default Load Industrial 25 Factory Default 【 P r o CM D : 99912100 】 Enable/ Disable Industrial 25 When the engine can not read Industrial 25, please read “ Enable Industrial 25 ” and try again.
nlscan.com Page 90 Symbols T ools Code Programming ON Code Programming OFF Industrial 25 Check Digit Industrial 25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It veri fi es the barcode message.
nlscan.com Page 91 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Industrial 25. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 92 Symbols T ools Code Programming ON Code Programming OFF Standard 25 Load Factory Default Load Standard 25 Factory Default 【 P r o CM D : 99912200 】 Enable/ Disable Standard 25 When the engine can not read Standard 25, please read “ Enable Standard 25 ” and try again.
nlscan.com Page 93 Symbols T ools Code Programming ON Code Programming OFF Standard 25 Check Digit Standard 25 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last digit. It veri fi es the barcode message.
nlscan.com Page 94 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Standard 25. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 95 Symbols T ools Code Programming ON Code Programming OFF Code 39 Load Factory Default Load Code 39 Factory Default 【 P r o CM D : 99912400 】 Enable/Disable Code 39 When the eng.
nlscan.com Page 96 Symbols T ools Code Programming ON Code Programming OFF Code 39 When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to error beep.
nlscan.com Page 97 Symbols T ools Code Programming ON Code Programming OFF Code 39 T ransmit Start & Stop Character Code 39 has one "*" before and another after digits as Start & Stop Character . T ransmission of “ * ” can be selected.
nlscan.com Page 98 Symbols T ools Code Programming ON Code Programming OFF Code 39 Select Message Length Code 39 Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length “ .It is used to program the valid reading length of Code 39.
nlscan.com Page 99 Symbols T ools Code Programming ON Code Programming OFF Codabar Load Factory Default Load Codabar Factory Default 【 Pro CMD : 99912500 】 Enable/Disable Codabar When the engine can not read Codabar , please read “ Enable Codabar ” and try again.
nlscan.com Page 100 Symbols T ools Code Programming ON Code Programming OFF Codabar When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to error beep.
nlscan.com Page 101 Symbols T ools Code Programming ON Code Programming OFF Codabar T ransmit Start & Stop Character Do Not T ransmit Both Start & Stop Character 【 Pro CMD : 99912506 】 U.
nlscan.com Page 102 Symbols T ools Code Programming ON Code Programming OFF Codabar Select Message Length Codabar Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length “ .It is used to program the valid reading length of Codabar .
nlscan.com Page 103 Symbols T ools Code Programming ON Code Programming OFF Code 93 Load Factory Default Load Code 93 Factory Default 【 P r o CM D : 99912600 】 Enable /Disable Code 93 When the engine can not read Code 93, please read “ Enable Code 93 ” and try again.
nlscan.com Page 104 Symbols T ools Code Programming ON Code Programming OFF Code 93 When “ Check, Do not T ransmit Check digit ” is enabled and barcode message length minus one is less than Min Message Length, it will lead to error beep.
nlscan.com Page 105 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Code 93. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 106 Symbols T ools Code Programming ON Code Programming OFF Code 1 1 Load Factory Default Load Code 1 1 Factory Default 【 P r o CM D : 99912700 】 Enable/ Disable Code 1 1 When the engine can not read Code 1 1, please read “ Enable Code 1 1 ” and try again.
nlscan.com Page 107 Symbols T ools Code Programming ON Code Programming OFF Code 1 1 Check Digit Code 1 1 may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last one or two digits. It veri fi es the barcode message.
nlscan.com Page 108 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Code 1 1. The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 109 Symbols T ools Code Programming ON Code Programming OFF Plessey Load Factory Default Load Plessey Factory Default 【 P r o CM D : 99913000 】 Enable/ Disable Plessey When the engine can not read Plessey , please read “ Enable Plessey ” and try again.
nlscan.com Page 1 10 Symbols T ools Code Programming ON Code Programming OFF Plessey Check Digit Plessey may include Check Digits (not compulsory) following its barcode messages. If included, they are the last two digit. They veri fi e the barcode message.
nlscan.com Page 1 11 Symbols T ools Code Programming ON Code Programming OFF Select Message Length It is used to program the valid reading length of Plessey . The engine will send an error beep, if the decoded data length does not match the valid length.
nlscan.com Page 1 12 Symbols T ools Code Programming ON Code Programming OFF MSI-Plessey Load Factory Default Load MSI-Plessey Factory Default 【 P r o CM D : 99913100 】 Enable/ Disable MSI-Plessey When the engine can not read MSI-Plessey , please read “ Enable MSI-Plessey ” and try again.
nlscan.com Page 1 13 Symbols T ools Code Programming ON Code Programming OFF MSI-Plessey Check Digit MSI-Plessey may include Check Digit (not compulsory) following its barcode messages. If included, it may be the last one or two digits. It veri fi es the barcode message.
nlscan.com Page 1 14 Symbols T ools Code Programming ON Code Programming OFF Select Message Length MSI-Plessey Message Length is de fi ned by “ Min. Message Length ” and “ Max. Message Length ” .It is used to program the valid reading length of MSI-Plessey .
nlscan.com Page 1 15 Symbols T ools Code Programming ON Code Programming OFF GS1 Databar Load Factory Default Load GS1 Databar Factory Default 【 P r o CM D : 99913200 】 Enable/ Disable GS1 Databar When the engine can not read GS1 Databar , please read “ Enable GS1 Databar ” and try again.
nlscan.com Page 1 16 Appendix Factory Default List Parameters Factory Default Remark General Programming Code Programming On Send Pro Code V alue Off W orking Mode Hand-held Mode Reading a Barcode T ime Length 3s Range : 0-15s , 0 is in fi nite time.
nlscan.com Page 1 17 Appendix Factory Default List Parameters Factory Default Remark Symbol Code 128 Enable On Max Message Length 255 Min Message Length 1 UCC/EAN-128 Enable On Max Message Length 255 .
nlscan.com Page 1 18 Appendix Factory Default List ISSN Enable Off ISBN Enable Off Use 10 Digits Off UPC-E Enable On Send Check Digit On Enable 2 Digits Addenda Code Off Enable 5 Digits Addenda Code O.
nlscan.com Page 1 19 Appendix Factory Default List Deutsche 14 Enable Off Send Check Digit On Deutsche 12 Enable Off Send Check Digit On COOP 25(Japanese Matrix 25) Enable Off Check Off Send Check Dig.
nlscan.com Page 120 Appendix Factory Default List Support Full ASCII On Max Message Length 255 Min Message Length 4 No less than 4 (including St a rt & St o p Ch a ra ct e r) Codabar Enable On Che.
nlscan.com Page 121 Appendix Factory Default List Max Message Length 255 Min Message Length 4 No less than 1 MSI-Plessey Enable Off Send Check Digit Off No Check On 1 D ig it , MOD10 Check Off 2 D ig .
nlscan.com Page 122 Appendix AIM ID List Symbol AIM ID Possible AIM ID Modi fi ers(m) Code 128 ]C 0 UCC/EAN-128 ]C 1 AIM 128 ]C 2 IS B T 1 2 8 ]C 4 EAN-8 ]E 4 EAN-13 ]E 0 EAN-13 with Addon ]E 3 ISSN .
nlscan.com Page 123 Appendix Code ID List Symbol Code ID Code 128 j UCC/EAN-128 u AIM 128 f IS B T 1 2 8 t EAN-8 g EAN-13 d ISSN n ISBN B UPC-E h UPC-A c Interleaved 2 of 5 e ITF-6 r ITF-14 q Deutsche.
nlscan.com Page 124 Appendix Appendix T ools Code Programming ON Code Programming OFF Digit Code It is must to read save after reading digit code. 0 【 Pro CMD :99900000】 1 【 Pro CMD :9990000.
nlscan.com Page 125 Appendix Digit Code 8 【 Pro CMD :99900010】 9 【 Pro CMD :99900011】 A 【 Pro CMD :99900012】 B 【 Pro CMD :99900013】 C 【 Pro CMD :99900014】 D 【 Pro CMD .
nlscan.com Page 126 Appendix Appendix T ools Code Programming ON Code Programming OFF Save and Abort In order to save the received data “ Save ” has to be read after data transition completed. If error occurs when reading data, the wrong data can be deleted and the setting up can be done again.
nlscan.com Page 127 Revisions V ersion Data Source Description Date Approved Pre-release version 20090826.
Ein wichtiger Punkt beim Kauf des Geräts Newland EM1300 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Newland EM1300 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Newland EM1300 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Newland EM1300 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Newland EM1300 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Newland EM1300 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Newland EM1300 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Newland EM1300. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Newland EM1300 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.