Benutzeranleitung / Produktwartung EA274WMi des Produzenten NEC
Zur Seite of 27
MultiSync EA274WMi User ’ s Manual.
Inde x W arning, Caution ..........................................................................................................................English-1 Registration Information .....................................................................
English-1 English W ARNING CA UTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM W ALL SOCKET . T O FULL Y DISENGAGE THE POWER T O THE UNIT , PLEASE DISCONNECT THE POWER CORD FROM THE AC OUTLET .DO NOT REMOVE COVER (OR BACK).
English-2 Registration Inf ormation FCC Inf ormation 1. Use the attached specifi ed cables with the MultiSync EA274WMi (L273QL) monitor so as not to interfere with radio and television reception. (1) The power supply cord you use must have been approved by and comply with the safety standards of U.
English-3 English Recommended use Safety Precautions and Maintenance FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND USING THE LCD COLOR MONIT OR: • DO NO T OPEN THE MONIT OR. There are no user serviceable parts inside and opening or removing covers may expose you to dangerous shock hazards or other risks.
English-4 CORRECT PLACEMENT AND ADJUSTMENT OF THE MONITOR CAN REDUCE EYE, SHOULDER AND NECK F A TIGUE. CHECK THE FOLLOWING WHEN YOU POSITION THE MONITOR: • For optimum performance, allow 20 minutes for the display to warm up. • Adjust the monitor height so that the top of the screen is at or slightly below eye level.
English-5 English Contents Y our new NEC monitor box* should contain the following: • MultiSync monitor with tilt/swivel/pivot/height adjust stand • Power Cord* 1 • Video Signal Cable (DisplayPort cable) • Video Signal Cable (DVI-D to DVI-D cable)* 2, * 4 • USB Cable* 3 • ControlSync Cable (ø 2.
English-6 Quic k Star t T o connect the LCD monitor to your system, follow these instructions: NO TE: Make sure to read “Recommended Use” (page 3) before installation.
English-7 English 3. Place hands on each side of the monitor to tilt the LCD panel 30-degree angle and lift up to the highest position. 4. Connect all cables to the appropriate connectors ( Figure C.
English-8 8. T urn on the computer and the monitor by pressing the power key on the front bezel ( Figure E.1 ). 9. No T ouch Auto Adjust automatically adjusts the monitor to optimal settings upon initial setup.
English-9 English Figure S.1 Tilt and Swivel Grasp the top and bottom sides of the monitor screen with your hands and adjust the tilt and swivel as desired ( Figure TS.1 ). Figure TS.1 NO TE: Handle with care when tilting the monitor screen. Flexib le Arm Installation This LCD monitor is designed for use with a fl exible arm.
English-10 Mount Flexib le Arm This LCD monitor is designed for use with a fl exible arm. 1. Follow the instructions on how Remove Monitor Stand for Mounting to remove the stand. 2. Use the 4 screws removed from the stand to attach the arm to the monitor ( Figure F .
English-11 English Contr ols OSD (On-Screen Displa y) control ke ys on the front of the monitor function are as f ollows: T o access OSD menu, touch any of the control keys. T o change signal input, touch the SELECT key . NO TE: Exit OSD in order to change signal input.
English-12 ECO T OOLS BRIGHTNESS Adjusts the overall image and background screen brightness. If ECO MODE is set to 1 or 2, a bar for CARBON FOOTPRINT will appear . CONTRAST Adjusts the overall image and background screen brightness by input signal level.
English-13 English HUMAN SENSING The sensor on the front side of the monitor detects the movement of a person by using the HUMAN SENSING function. THE HUMAN SENSING has three settings: OFF: No human sensing.
English-14 FINE (Analog input only) Improves focus, clarity and image stability by increasing or decreasing this setting. If the “Auto Adjust” function and the “H.Size” function do not give you a satisfactory picture setting, a fi ne tuning can be performed by using the “Fine” function.
English-15 English T ools V OLUME Controls the volume of the speakers or headphones. T o mute the speaker output, touch the “PBP/RESET” key . SOUND INPUT (HDMI, DisplayP or t inputs onl y) This function selects Audio Input, HDMI or DisplayPort. VIDEO DETECT Selects the method of video detection when more than one video inputs are connected.
English-16 USB PO WER Selects a power relation of USB. AU TO : Power is supplied to USB downstream port depending on related power condition. ON: Power is always supplied to USB downstream port even when in power save mode or power OFF . NO TE: Power consumption depends on connected USB even when a monitor ’s power is of f.
English-17 English ECO Inf ormation CARBON SA VINGS: Displays the estimated carbon savings information in kg. CARBON USA GE: Displays the estimated carbon usages information in kg. This is the arithmetic estimation, not actual measurement value. COST SA VINGS: Displays the electricity cost savings in balance.
English-18 Specifi cations Monitor Specifi cations MultiSync EA274WMi Notes LCD Module Diagonal: Viewable Image Size: Native Resolution (Pixel Count): 68.47 cm/27.0 inches 68.47 cm/27.0 inches 2560 x 1440 Active matrix; thin fi lm transistor (TFT) liquid crystal display (LCD); 0.
English-19 English Features DisplayP or t: DisplayPort is designed to be the future-ready and scalable solution for high performance digital display connectivity . It enables the highest resolutions, the fastest refresh rates and deepest color depths over standard cables.
English-20 T roub leshooting No picture • The signal cable should be completely connected to the display card/computer . • The display card should be completely seated in its slot. • The monitor does not support DisplayPort converter signal. • Front Power Switch and computer power switch should be in the ON position.
English-21 English No Video • If no video is present on the screen, turn the Power button off and on again. • Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).
English-22 Using the A uto Brightness function The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly .
English-23 English Contr olSync 1. Connect the master monitor with a sub monitor via a ControlSync cable (ø 2.5) into ControlSync IN/OUT . 2. Follow the steps of DA T A COPY . When the setting of the master monitor is adjusted, it will be copied and sent to the connected sub monitor(s) automatically .
English-24 TCO Cer tifi ed Edg e Displa ys 1.2 Congratulations! This product is TCO Certifi ed – for Sustainable IT TCO Certi Þ ed is an international third party sustainability certi Þ cation for IT products.
English-25 English NEC DISPLA Y SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’ s top priorities in trying to minimize the burden placed on the environment.
Ein wichtiger Punkt beim Kauf des Geräts NEC EA274WMi (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie NEC EA274WMi noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für NEC EA274WMi - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von NEC EA274WMi reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über NEC EA274WMi erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon NEC EA274WMi besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von NEC EA274WMi verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit NEC EA274WMi. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei NEC EA274WMi gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
