Benutzeranleitung / Produktwartung MTCBA-G-F des Produzenten Multi-Tech Systems
Zur Seite of 61
MultiModem ä GSM/GPRS External Wireless Modem (Data/Fax/Voice) MTCBA-G-F1 MTCBA-G-F2 UserGuide.
2 User Guide for MultiModem G SM/GPRS External Data/Fax/Voice Wireless Modem Models MTCBA-G-F1 & MTCBA-G-F2 P/N 82001220, Rev ision A Copyr ight © 2003 by Multi -Tech Sy stems, Inc. All rights reserved. This publication may not be reproduced , in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc.
3 Contents P RODUCT D ESCRIPT I ON 5 Package Contents 6 Interfaces 6 Parts to be Suppl ied by Wi reless Service Provi der 7 Parts t o be Supplied by End User 7 Radio Charact eris tics 8 Accesso ry Kit.
4 Electrical Installatio n & Configuratio n 28 Mobile Phonet ools 34 Verifyi ng signal s trengt h 35 Verifyi ng network r egistr ation 36 Test ing the Confi guration 37 Tes ting the Conf igur atio.
Product Description 5 Pr oduct Description The Multi-Tech MultiM odem GSM/GPRS is an exter nal data/fax/voice wireless mod em. It also supports mobile originated short message service (SMS) and mo bile-term inat ed SMS. Design ed for global use, it offers st andards-based multi-band GSM/GPRS Class 10 per formance .
Product Description 6 P acka ge Contents · one modem · two holding bridles (mounting brackets) · one RS- 232 15-to-9- pin cabl e · one power supply cable with fuse · one User Manual (this docu me.
Product Description 7 P arts to be Supplied b y Wireless Service Pr ovider · Subscriber Identity Module (SIM) configuration chip The SIM contains information specific to your wireless account and its features. P arts to be Supplied by End User · mounting screws ( screw shaf t diamete r = .
Product Description 8 Radio Characteristi cs GSM 850 EGSM 900 Frequency RX 869 to 894 MHz 925 to 960 MHz Frequency TX 824 to 849 MHz 880 to 915 MHz RF Power Stand 2W at 12.
Product Description 9 Accessory Kit A Wireless MultiModem A ccessory Kit is available. Generally spea king, it is useful to have one or two kits to c onfigure a group or fleet of Wireless MultiMod em units (generally, you will not need one kit for every modem).
Product Description 10 A T Command Inf o This manual describe s a minimal set of AT commands that ar e adequate for c onfiguring many common application situations. A complete set of AT command definitions can be found in the A T Command manuals ( one for GSM/G PRS an d one for CDMA).
Product Description 11 · For GSM-without-GPRS , a circuit- switched data con nection is used. The user can set up DUN to make a conventional V.32 mode m connection to any terminating modem at the other end.
Product Description 12 Features · GPRS Class 10 ope ration · V.42bis d ata compression · Dual-band 850/1900 or 900/1800 GSM/GPRS · Numerous LEDs provide operational status · GSM Cl ass 1 and Clas.
Application Overview 13 Application Overview Application T ypes With circuit switched data rates up to 14.4K bp s, the MultiModem GSM/G PRS is targeted at applications that period ically need to send or receive data over a wireless network.
Application Overview 14 R S232 Wir el ess Mu ltiM ode m used i n re m ot e A TM ap pli cat io n..
Application Overview 15 Benefits/Features in Applicat ions Short Development Time. The MultiModem GSM/ GPRS can make your existing and next generation device, m achine, or s ystem, communication-ready without requiring any hardware cha nges to its design.
Application Overview 16 Compatible Supplementary Service s . The MultiModem GS M/GPRS is compatible with supplementary services such as call forwarding, call barring, multiparty, ca ll waiting and call hold, calling line identifi cation, advice of charge, US SD, closed user group and explicit call transfer.
Application Overview 17 Industrial Chassis . The MultiModem GSM/GPRS is packaged in a rugged , water resistant, industrial chassis. The chassis has an RS-232 DE -15 Voice /Data interf ace conne ctor and a permanent screw-type po wer connector. It also has an SMA antenna connector .
Application Overview 18 Functions – GSM Modes MODE DESCRIPTION Standa rd Dual Ban d Extended GS M 900 MHz Class 4 (2W) and GSM 1800/ 1900 MHz Class 1 (1 W) Interface Serial i nter face RS232. V. 24/V.28 Autobaudi ng function. A T comma nd set based on V .
Specificatio ns 19 Specifications General Specifications Power Requirements 5 V to 32VDC; 400mA Averag e @5V, 2A Peak @ 5V Mechanical Dimensions & W eight 4.
Specificatio ns 20 Electrical Charact eristics Switching the GS M modem on/off The device is permanently powered (when connected to the power supply). Voltage Range Voltage ran ge : 5 to 32 V DC GND :.
Specificatio ns 21 Input/out put el ect r i cal characterist i cs for external connecti ons INSTALLATION / START- U P GSM 850/900 GSM 1800/1900 Parameters Min Typ. Max Min Typ Max Unit Power Supply @ 25 degrees C: - Input Supply Voltage 5 13.2 32 5 13.
Specificatio ns 22 Input/out put el ect r i cal characterist i cs (cont’d) GSM 850/900 GSM 1800/1900 Parameters Min Typ. Max Min Typ Max Unit Power Supply @ 25 degrees C: - Input Supply Voltage 5 13.2 32 5 13.2 32 V @5V 31.4 31.4 mA @13.2 V 13.2 13.
Specificatio ns 23 LED Indicators TD . Transmit Data. Lit when modem is tr ansmitting data. RD . Receive Data. Lit when modem is rec eiving da ta. CD . Carrier Detect. Lit when data connection has been estab lished. LS . Line Status. Continuous “on” state indicates that the wireless modem is not registered on the network.
Specificatio ns 24 RS232 15-Pin Connector Pinout 10 11 6 1 5 15 PIN EIA CCIT Designation 1 DCD 109 Data Carrier Direct 6 RX 104 Receiv e Data (out) 2 TX 103 Transmit Data 8 DTR 108.
Getting Sta r ted 25 Getting Star ted with your Wireless MultiModem Mechanical Mounting To mount the Wireless MultiModem, do the following: 1. Obtain m ounting screw s (two are needed) th at are appr opriate for the surface on which you will mount the MultiModem.
Getting Sta r ted 26 For example, one m ight use two 6-3 2 self- tapping scre ws 5/8” in length to mount the unit in a truck to the wa ll of the cab behind the passenger’s seat. 2. Typically, the unit is mounted against a flat surface into which holes can be drilled.
Getting Sta r ted 27 3. Slide the mounti ng bridles into the corresponding slots on the back side of the MultiMode m chassis. 4. Attach the MultiMo dem with two screws to the mounting s urface at the desi red location o n the equipment.
Getting Sta r ted 28 Electrical Installation & C onfiguration The wireless MultiModem requires the power supply connection to begin opera tion. It also requires a SIM card (Su bscriber Ident ity Modu le) to operate on a G SM network. To ins tall the modem, do the following: 1.
Getting Sta r ted 29 2. Insert the SIM ca rd into the ho lder..
Getting Sta r ted 30 3. Ver ify t hat the SIM ca rd fits into the holder properly and then replace the cover..
Getting Sta r ted 31 4. Connec t a suitable ante nna to the S MA connector (see s pecifications o n page 8). An te nna C onn ect or (SMA type).
Getting Sta r ted 32 5. Connect bo th sides of the s erial and co ntrol cable (15-pin Sub D co nnector on th e modem side). Seri a l & Con t rol C onn e ct or T o Ser ial Port of PC.
Getting Sta r ted 33 6. Plug the power supply ca ble into the wireless Multimodem. Po we r Cord In-Line Fus e Power Connector T o Power Source 7. Connect the po wer supply cable into the po wer supply, with a correct GND con nection. Connect red wire to + (positive) an d black wire to – (negat ive).
Getting Sta r ted 34 Connect the power supply to its source (f or example, in a m obile situation, to the vehicle’s DC fuse/terminal block). 8. Activate the power supply. Mobile Phonetools For initial configuration of your wireless device, Multi-Tech off ers a Windows â based mobile Phone Tools application.
Getting Sta r ted 35 V erifying signal strength The Wireless MultiModem es tablishes a call if the signal is su fficien tly st rong. To v erify th e signal strength, do the following: 1. Using the Hy perterminal program at the computer to which the Wireless MultiModem is connected, type th e AT comman d AT+CSQ.
Getting Sta r ted 36 V erifying network registration In this procedure, you w ill verify that the Wireless MultiModem has been registered on the w ireless network.
Getting Sta r ted 37 T esting the Configuration Descrip- tion A T Comman ds Response Returned Commen ts A T+CPIN =1234 O K PIN Code accepted +CME E RROR : 16 Incorrect PIN Code Enter PIN Code +CME E R.
Getting Sta r ted 38 T esting the Configuration (continued) Descrip- tion A T Comman ds Response Returned Commen ts R ING A TA Answer the ca ll. Receiving an incom ing call O K A TD1234; Don’t for get the “;” at the end fo r “voice” calls.
Getting Sta r ted 39 T esting the Configuration (continued) Descrip- tion A T Comman ds Response Returned Commen ts Initiate a n emergenc y call A TD112; O K Don ’t forget the “;” at the end fo r “voice” calls.
Troubleshooting 40 T r oubleshooting Situati on A: The modem does not answ er through the serial l i nk If the Wir eless MultiMo dem does no t answer through the serial link upon an attem pted transm ission of data or voice signa ls, see the table below for possible causes an d solutions.
Troubleshooting 41 Solutions for ‘no connection through serial link’ situation (cont’d) If the modem returns … Then as k … Action Is the comm unication program properly confi gured ? In co m.
Troubleshooting 42 Situation B: The modem always returns «Error» when trying t o i ssue a communication If the Wireless MultiModem returns a m essage of error upon an attem pted transmission of data or voice signals, see the table below for possible caus es and s olution s.
Troubleshooting 43 Solutions for “error” message situations (cont’d) If the m odem returns … Then as k … Action error (cont’d) Is the selected bearer type support ed by t he called party ? Is the selected bearer type support ed by t he network? In com m.
Troubleshooting 44 Interpretation of Ex tended Error Codes related to “error” message Error Code Diagnostic Hint 0 Phone f ailu re Call t echnical support 3 Ope rati on not allowed No action. 4 Ope rati on not support ed No action. 10 SIM not inserted Do one of the follow ing: Insert the SIM card into the modem ’s SIM holder.
Troubleshooting 45 Interpretation of Ex tended Error Codes related to “error” message (cont’d) Error Code Diagnostic Hint 17 SIM PIN2 required Enter PIN2 code . 18 SIM PUK2 require d Enter PUK 2 code. Note: Call y our netw ork provider if y ou do not know this code.
Troubleshooting 46 Interpretation of Ex tended Error Codes related to “error” message (cont’d) Error Code Diagnostic Hint 112 Location area not allow ed (#13) No action. 113 Roam ing not allow ed in this location are a (#13) No action. 132 Servic e option not supported ( #32).
Troubleshooting 47 Situation C: The modem alwa ys returns «No carrier» when trying to issue a communicat ion Solution s for “n o carrier” message If the modem returns … Then as k … Action no carrier (esp.
Troubleshooting 48 Solution s for “n o carrier” message ( cont’d) If the modem returns Then as k … Action no carrier (esp. for voice communi- cation) Be sure that the semicolon ch aracter (“;” ) is typed imm ediately after the phone number in the AT comm and.
Troubleshooting 49 Interpretation of Ex tended Error Codes related to “no carrier” message Error Code Diagnostic Hint 1 Unallocated phone n um ber Not allocated 16 Normal call clearing 17 User bus.
Troubleshooting 50 Interpretation of Ex tended Error Codes related to “no carrier” message (cont’ d) Error Code Diagnostic Hint 50 Reques ted facility not subscribed Check y our subscription (da.
Safety 51 Safety General Safety The modem is design ed for and in tended to be u sed in f ixed and m obile applications. “F ixed” m eans that th e device is physically secured at one location and is not able to be easily move d to another location.
Safety 52 It is important to follow any special regulations regarding the use of radio equipmen t due in particular to the possibility of radio frequency , RF, interference. Please f ollow th e safety advice giv en below carefully . · Switch OFF y our Wireless MultiModem when in an a ircraft.
Safety 53 Ve h i c l e S a f e t y · Do not use y our Wireless MultiMode m w h ile driving , unless equipped w ith a correc tly installe d vehicl e kit allow ing ‘Hands- Free’Operatio n. · Respec t national re gulations on the use of cellular telephones in vehicles.
Safety 54 · Do not expose the Wireless MultiM odem to water, rain or spilt bever ages . It is not w aterproof . · Do not abuse your W ireles s MultiModem by dropping , knock ing, or v iolently shaking it.
Warranty & Repair 55 W arranty & Repairs P olicies W arranty Multi-Tech Systems, Inc., (herea fter “MTS” ) warrants t hat its products will b e free from defects in ma terial or workm anship for a period of two years from da te of purchase, or if proof of purchase is not provided, two from dat e of shipment.
Warranty & Repair 56 MTS WILL NOT BE LIA BLE FOR CONSEQUENTIA L DAMAGES, AND UNDER NO CIRCUMSTANCE S WILL ITS LIABILITY EXCEED THE P RICE FOR DEFECTIVE PRODUCTS.
Warranty & Repair 57 For out of warra nty repair c harges, go to www.multi tech.co m/doc uments/ warrant ies Exten ded two-y ear o vern ight replacement service agreements are avail able fo r sel ected pr oducts . Pleas e call MT S at (888) 288-5470, ex tens ion 5308 o r vis it our web s ite at http:/ /www.
Warranty & Repair 58 Repair Procedures for Int ernational Customers (Outsi de U.S.A. and Canada) Your original point of purc hase Reseller may offer t he quickest and most econom ical repair opt ion for your Multi-Tech product.
Warranty & Repair 59 Please d irect y our qu estion s reg ardi ng tech nical matte rs, product con figur ation, verif ication th at the pr oduct is defective, et c., to our Technic al Support department nearest you or email t support@multit ech.com.
Referenc e Info 60 Wireless Modem Reference Inf o GSM re fe rence docume nts : G SM 03.40, GSM 03.45, G SM 04.11, GSM 04.21, G SM 05.08, GSM 07.01, GSM 07.02, G SM 07.05, GSM 07.07. ETSI con tact : ETSI Secretariat F-06921 Sophia A ntipolis Cede x, France e-mail : secretariat@etsi.
82001220.
Ein wichtiger Punkt beim Kauf des Geräts Multi-Tech Systems MTCBA-G-F (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Multi-Tech Systems MTCBA-G-F noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Multi-Tech Systems MTCBA-G-F - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Multi-Tech Systems MTCBA-G-F reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Multi-Tech Systems MTCBA-G-F erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Multi-Tech Systems MTCBA-G-F besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Multi-Tech Systems MTCBA-G-F verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Multi-Tech Systems MTCBA-G-F. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Multi-Tech Systems MTCBA-G-F gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
