Benutzeranleitung / Produktwartung 7000 des Produzenten Asante Technologies
Zur Seite of 39
FriendlyNET 7000 Series Gigabit Ethernet Switches User’ s Manual.
Copyright N otice T rademarks Asanté T echnologies and F riendlyNET ar e trademarks of Asanté T echnologies, Inc. Ethernet is a registered trademark of the Xerox Corporation. A ll brand names and products are trademarks or registered trade- marks of their respective holders.
Page i T able of Contents About This Manual ...............................................iii Chapter Contents .............................................. iv Document Conventions ..................................... iv Introduction ..............
Page ii Cabling Requirements .................................... 2-8 Connecting Network Devices ......................... 2-9 Connecting a Computer to the Switch ...... 2-9 Connecting a Hub or a Switch to the Asanté Switch ..........................
Page iii About This Man ual This manual describes the complete line of F riendlyNET 7000 Series G igabit S witches. The manual often focuses on two models: ❑ FS7108 — eight-port 10/100Mbps F ast E.
Page iv Chapter Contents This manual is divided into the following chapters and appendices: ❑ Chapter 1, “Introduction,” pro vides an overview of FriendlyNET 7000 Series Gigabit S witches, their.
Page 1-1 1 Intr oduction This chapter introduces Asanté F riendlyNET 7000 S eries G igabit S witches and provides an o ver view of switching technology . Intr oducing the FriendlyNET 7000 Series Thank you for purchasing an Asanté F riendlyNET 7000 Series Gigabit S witch.
Introduction Page 1-2 A Media I ndependent Interface (MII) slot is built in to the back panel of all 7000 Series S witches. An Asanté 100 FX MII module can easily be plugged in to allow for 100Base-FX connections.
Introducing the FriendlyNET 7000 Series Page 1-3 Features The F riendlyNET 7000 Series G igabit S witch has the following featur es: ❑ Compact size — designed for small to large workgroups in spac.
Introduction Page 1-4 ❑ Complies with IEEE 802.3 Ethernet, IEEE 802.3u F ast Ethernet, IEEE 802.3z Gigabit E thernet, and IEEE 802.3x flow control (in full-duplex mode) standards ❑ W orks with Ca.
Switching Technology Page 1-5 T o ensure network r eliability , a switch monitors each of its ports for signal quality . The switch automatically disconnects stations transmitting excessive noise, then reconnects them when the problem is r esolved. A switch also automatically drops data packets that exceed the maximum allo wable length.
Introduction Page 1-6.
Page 2-1 2 Installation This chapter describes the components and explains how to install, mount, and apply power to your F riendlyNET 7000 Series Gigabit S witch.
Installation Page 2-2 Components This section describes the front- and back-panel layouts of the FS7108 and FS7016 S witches. The only control on the front panel is the uplink push-button switch. The only control on the rear panel is the po wer switch.
Expansion Modules Page 2-3 FS7016 Base Unit The front panel of the FS7016 contains sixteen 10/100Mbps ports, two expansion slots, one uplink switch button, and LED indicators. See F igure 2-3. F igure 2-3 F riendlyNET 7016 front panel The back panel of the FS7016 contains a 100–240 volt AC po w er connector , a power switch and an MII slot.
Installation Page 2-4 T o install the Gigabit SX XP M odule: 1 P ower down the unit. 2 Remo ve the metal cov er from the front of an empty expan- sion slot (located on the S witch ’ s front panel) using a small Phillips screwdriver . 3 Align the bottom of the Gigabit module with the rails on the inside of the expansion slot.
100 FX MII Module Page 2-5 ◆ Note: Each 10/100 expansion module provides 8 ports which are numbered 1 thr ough 8. I f the module is installed in Option Slot A, the ports on the module will correspond to LED indicators A1–A8. If the module is installed in Option Slot B, the ports on the module will correspond to LED indicators B1–B8.
Installation Page 2-6 2 Align the bottom of the MII module with the rails on the inside of the MII slot. 3 Slide the MII module into the MII slot until it stops, then push the module in until it seats with the connector .
Mounting Configurations Page 2-7 Desktop Mounting T o mount the S witch on a desktop or shelf: 1 Attach the four rubber feet (supplied) to the bottom of each corner on the S witch. See F igure 2-9. F igure 2-9 Desktop mounting 2 Place the S witch on a flat, stable, horizontal desktop or shelf.
Installation Page 2-8 2 Mount the S witch in the equipment rack by screwing the mounting brackets to the equipment rack. See F igure 2-11. F igure 2-11 M ounting the FS7000 in an equipment rack The rack mounting is complete. The Switch is ready for network connections.
Connecting Network Devices Page 2-9 Connecting Netw ork Devices This section describes how to connect computers, hubs and switches to the FS7000 S witch, and how to connect multiple FS7000 S witches together .
Installation Page 2-10 Connecting a Hub or a Switch to the Asanté Switch ❑ U se a two-pair Category 5 UTP straight-through cable with RJ-45 connectors ❑ Connect the hub ’ s uplink por t to any of the S witch ’ s por ts.
Voltage Requirements Page 2-11 Cascading Multiple FS7000 Switches M ultiple F riendlyNET 7000 Series S witches can be connected together (called cascading). See F igure 2-15. F igure 2-15 Cascading FS7000 S witches V oltage Requirements V oltage requirements for all models: ❑ 100 to 240 volts AC, 50/60Hz, 1.
Installation Page 2-12.
Page 3-1 3 LED Indicator s This chapter explains how to interpret the fr ont-panel LED indicators on F riendlyNET 7000 Series G igabit S witches. There are no LEDs on the rear panel.
LED Indicators Page 3-2 F igure 3-2 FS7000 LEDs U nits with a Gigabit SX XP module installed hav e the following additional LEDs for monitoring the status of the Gigabit port: ❑ Po w e r ❑ Link/Da.
LED Indicators for Port Connections Page 3-3 LED Indicators f or P or t Connections All FS7000 Series S witches include 100/10Mbps, Full/Half Duplex and Link/ Data LED indicators for each 10/100 port on the S witch. On the FS7108, the ports and LEDs are numbered 1–8.
LED Indicators Page 3-4 Link/Data LED The green Link/Data LED indicates whether a device is detected on the other end of the port, and whether activity is occurring.
LED Indicators on Gigabit SX Module Page 3-5 Full Duplex/Collision LED The Gigabit module ’ s green or amber Full D uplex/Collision LED indicates port operation in full- or half-duplex mode, and whether collisions are occurring on the port. T able 3-3 describes the possible status indications of the Gigabit Full Duplex/Collision LED.
LED Indicators Page 3-6.
Page A-1 A T r oubleshooting T able A-1 describes how to troubleshoot problems with your networ k and/or the S witch by monitoring the S witch ’ s LEDs. T able A-1 T roubleshooting Prob lem Action P o wer LED is off Make sure the po wer cord is connected to the po wer outlet and is properly inserted into the power connector on the switch.
Page A-2.
Page B-1 B Specifications FS7000 Series Specifications Standar ds IEEE 802.3 10Base-T Ethernet IEEE 802.3u 100Base-TX F ast Ethernet IEEE 802.3z 1000Base-X IEEE 802.
Page B-2 FS7000 Series Physical and En vironmental Specifications AC Inputs 100–240 volts AC, 50/60 Hz (internal universal po wer supply) P ower Consumption 15–30 watts (depends on model/configu.
Page B-3 Gigabit SX XP Module Specifications Standar ds IEEE 802.3z 1000Base-X IEEE 802.3x flow control Data T ransfer Rate Gigabit Ethernet 1000Mbps Networ k Cables Dual 62.
Page B-4.
Page C-1 C T echnical Support Contacting T echnical Support T o contact Asanté T echnical Support: T elephone (800) 622-7464 F ax (801) 566-3787 F ax-Back (800) 741-8607 E-mail support@asante.com W orld Wide W eb Site http://www .asante.com T echnical S upport Hours 6:00 a.
Page C-2.
ASANTÉ TECHNOLOGIES, INC., 821 FO X L ANE, SAN JOSE, CA 95131 PHONE: 800.622.7464 • F AX: 801.566.3787 • e-mail address: sales@asante.com • W orld Wide W eb site: http://www .asante.com ©1999 Asanté T echnologies Inc. Asanté is a trademark of Asanté T echnologies, Inc.
Ein wichtiger Punkt beim Kauf des Geräts Asante Technologies 7000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Asante Technologies 7000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Asante Technologies 7000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Asante Technologies 7000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Asante Technologies 7000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Asante Technologies 7000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Asante Technologies 7000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Asante Technologies 7000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Asante Technologies 7000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
