Benutzeranleitung / Produktwartung ISI5634PCI/4/8 des Produzenten Multi-Tech Systems
Zur Seite of 122
ISI5634PCI/4/8 User Guide.
User Guide Model ISI5634PCI/4/8 P/N S0000109, Revision D This publication may not be reproduced, in whole or in part, without prior expressed written permission from Multi-Tech Systems, Inc. All rights reserved. Copyright © 2001 by Multi-Tech Systems, Inc.
Contents Chapter 1—Introduction and Description ........................... 5 Introduction ............................................................................................ 6 How to Use This Manual ........................................
Linux Driver for ISI5634PCI-4/8 ............................................................. 6 0 LINUX: Pre-Installation Issues ........................................ 6 0 LINUX: Copy driver fr om the media ............................... 6 1 LINUX: Driver installation and loading .
Chapter 1—Introduction and Description.
6 ISI5634PCI/4/8 User Guide Introduction Welcome to the world of data communications. You have acquired one of the finest intelligent data and fax modems available today from one of Americas oldest and most respected modem manufacturersMulti- Tech Systems, Inc.
7 Chapter 1—Introduction and Description digital to analog only once before it reaches your modem. Upstream transmissions and transmissions between client modems are limited to data rates of 33.6 Kbps, as are downstream transmissions that are converted more than once on the telephone network.
8 ISI5634PCI/4/8 User Guide The processor, along with 256K bytes of RAM, works to allocate resources dynamically to the most active port. The ISI then generates one interrupt for an entire block of information and transfers the block to the systems microprocessor.
9 Chapter 1 — Introduction and Description What Is in Your Modem Package? Your modem package has several components. Make sure you have them all before trying to operate your modem.
10 ISI5634PCI/4/8 User Guide Technical Specifications Computer Requirements Pentium ® - based PC or compatible with PCI Bus Architecture One of these operating systems: Microsoft Windows 2000, NT v. 3.51 or v. 4.0; Windows 95, Windows 98 and Windows Me; Novell Netware versions 3.
Chapter 2 — Hardware Installation.
12 ISI5634PCI/4/8 User Guide Introduction Included in this chapter are two sets of instructions for installing the Multi-Tech ISI5634PCI card in your PCI bus personal computer. The first set of instructions is for installing the ISI5634PCI card. The second set contain instructions for installing the ISI5634PCI card and the auxiliary module.
13 Chapter 2 — Hardware Installation 4 . To avoid damaging the ISI5634PCI card and your PC, make sure your computer and any peripheral equipment connected to it are turned off. The ISI5634PCI can be installed in any Pentium equivalent PCI bus computer.
14 ISI5634PCI/4/8 User Guide Installing the ISI5634PCI card WITH the auxiliary module: 1 . The auxiliary module attaches to the ISI5634PCI card. If you already have this card installed, you must remove it from the PC to install the auxiliary module. 2 .
15 Chapter 2 — Hardware Installation 7 . Before installing the ISI5634PCI card, carefully line up the pin-out connectors of the ISI5634PCI card with the pin-out connectors of the auxiliary module. See figure below. Mounting screws Mounting posts Pin-out connectors 8 .
16 ISI5634PCI/4/8 User Guide 1 1 . Fasten the retaining bracket to computer chassis and replace cover. 1 2 . Plug one end of the phone cable into each modems LINE jack and the other end into a phone line wall jack. 1 3 . Turn on the power to the computer.
Chapter 3 — Software/Driver Installation.
18 ISI5634PCI/4/8 User Guide Introduction The ISI5634PCI card ships with drivers for each of the following operating systems: Windows ® 2000, Windows NT, Windows 95, Windows 98, Windows Me, Novell Netware versions 3.x and 4.x, SCO Open Server 5, and Linux.
19 Chapter 3 — Software/Driver Installation handling the ISI5634PCI board (the board should be kept in its shipping bag until used). During installation, handle the ISI5634PCI circuit card by its edges and keep one hand in contact with the PC chassis.
20 ISI5634PCI/4/8 User Guide 6 . The Install Hardware Device Drivers screen appears. Select "Search for a suitable driver ..." and click Next . 7 . The Locate Driver Files screen appears (Windows 2000 is seeking the driver for the ISI5634PCI card).
21 Chapter 3 — Software/Driver Installation 8 . The Driver File Search Results screen appears. Click Next . 9 . A progress screen will appear briefly while files are being copied.
22 ISI5634PCI/4/8 User Guide 1 0 . A completion screen will appear. Click Finish . 11. Immediately after the ISI driver installation has been completed, another Found New Hardware screen will appear briefly indicating that the MultiTech ISI Port has been detected.
23 Chapter 3 — Software/Driver Installation A second sequence of installation wizard screens appears. This sequence of screens deals with the setting up of ISI ports. The first screen in this sequence is the Found New Hardware Wizard -- Welcome screen.
24 ISI5634PCI/4/8 User Guide 13. The Locate Driver Files screen appears (Windows 2000 is seeking the ISI Port device driver). Select CD-ROM drives and click Next . 14. The Driver Files Search Results screen will indicate that the isiport.inf file has been found on the CD-ROM.
25 Chapter 3 — Software/Driver Installation 1 5 . A completion screen will appear. It will indicate that the first MultiTech ISI Port has been set up successfully.
26 ISI5634PCI/4/8 User Guide ISI5634PCI for Windows 2000: Installing Modems to COM Ports Pre-Requisite: Installation of Windows 2000 driver software must be completed before you can install the modems of the ISI5634PCI card. 1. Go to Start | Settings | Control Panel | Phone and Modem Options .
27 Chapter 3 — Software/Driver Installation 4 . At the Install New Modem screen, click on "Don't detect my modem ... " and click Next . 5 . If the software driver CD-ROM (or other media, in cases of using drivers downloaded from the MultiTech web site) is not already in the appropriate disk drive in the PC, insert it now.
28 ISI5634PCI/4/8 User Guide 7. The Install from Disk screen will appear. Type or browse for the file path of the modem software (for example, E:servcarddriverswin2000). Click OK . 8. The Install New Modem screen will appear. Highlight ISI5634PCI -8 PCI 56K Modem.
29 Chapter 3 — Software/Driver Installation 9. The Install New Modem - port list screen will appear. Highlight the COM ports on which you want modems to be installed. You must allocate 4 ports for the ISI5634PCI-4, or 8 ports for the ISI5634PCI-8.
30 ISI5634PCI/4/8 User Guide 11. Screens denoting the installation of modems to specific COM ports will appear for each modem installed. 1 2 . A completion screen will appear.
31 Chapter 3 — Software/Driver Installation 13. The Phone and Modems Options screen ( Modems tab) will re- appear and display the modems that have just been assigned to COM ports. Installation of modems to COM ports in Windows 2000 is now complete. Remove ISI5634PCI Driver (Windows 2000) 1.
32 ISI5634PCI/4/8 User Guide ISI5634PCI for Windows 2000: Installing ISI Manage- ment Software (server OSs only) If you are using a Windows 2000 Server operating system ("Server" or "Advanced Server"), you must decide whether you want to use the MultiTech ISI Management Software in conjunction with your ISI5634PCI board.
33 Chapter 3 — Software/Driver Installation Installing the ISI5634PCI Card in Windows NT 3.51/4.0 The following procedure describes how to install the ISI5634PCI in a system operating Microsoft Windows NT 3.51 or 4.0 for use with Remote Access Service (RAS) server and other communications/fax server type applications.
34 ISI5634PCI/4/8 User Guide 5 . Click Start , Settings , Control Panel , and then double-click Network . In the Network dialog box, click the Adapters tab.
35 Chapter 3 — Software/Driver Installation 7 . The Insert Disk dialog box appears. Type in or browse for the path (file directory location) of the Windows NT driver (for example, E:servcarddriverswinntsetup.exe). C l ick OK . 8 . The Select OEM Option dialog box appears.
36 ISI5634PCI/4/8 User Guide 1 1 . The ISI Cards dialog box appears again showing the port resource allocation that has just been made. To add additional ISI5634PCI cards, click Add and repeat step 10. After the last ISI card has been added, click Close in the ISI Cards dialog box.
37 Chapter 3 — Software/Driver Installation 1 3 . After bindings are reviewed and stored, the Network Settings Change dialog box appears. Click Yes to reboot your system. The ISI5634PCI now is installed in Windows NT and you are ready to install modems.
38 ISI5634PCI/4/8 User Guide 4 . The Install New Modem - Models dialog box appears. Highlight ISI5634PCI-8 PCI 56K Modem and click Next . 5 . Select ports for modem use. For the ISI5634PCI-4, you should have reserved four ports during driver installation.
39 Chapter 3 — Software/Driver Installation 6 . After the modems install to the ports, click Finish to return to the General tab. 7. To view COM port assignments (and make changes if necessary), use the Modem Properties dialog box.
40 ISI5634PCI/4/8 User Guide 8. When finished, close the Modem Properties dialog box. The message below appears asking if you want to configure Dial-Up Networking. Click Yes . 9 . The Remote Access Setup dialog box appears. Click Add . 10. Each COM port appears in a separate Add RAS Device dialog box.
41 Chapter 3 — Software/Driver Installation 1 1 . The Remote Access Setup dialog box displays again. Repeat steps 9 and 10 until all modems are added. 1 2 . When all modems have been added, click Continue . 13. After bindings have been reviewed and stored, you will be prompted to re-start your computer.
42 ISI5634PCI/4/8 User Guide Removing ISI5634PCI Driver in Windows NT 3.51/4.0 1 . Click Start , Settings , Control Panel , and then double-click Network . 2 . The Network dialog box appears. Click the Adapters tab. 3 . Select Multi-Tech 4, 8, 16-port ISI Card, and then click Remove .
43 Chapter 3 — Software/Driver Installation 6. (Follow either 6A or 6B, but not both.) A. From Windows Explorer, open the 95-98-Me directory on the CD-ROM (for example, E:SERVCARDDRIVERS95-98- MESETUP.EXE) or floppy drive that contains the ISI driver file.
44 ISI5634PCI/4/8 User Guide 9. Under Select Type of Card , do not check the Install ISA Card box. Click Next . 10. A completion screen appears. 11. When prompted to restart your computer, click Yes and click OK . 1 2 . During the re-start process, Windows 95/98/Me will detect the ISI5634PCI card.
45 Chapter 3 — Software/Driver Installation 13. The next screen asks, What do you want Windows to do? Click on Search for the best driver for your device. Click Next . 14. When asked for the location at which Windows 95/98/Me should search for the new driver, check Specify a Location and enter the path (file directory location) of the driver.
46 ISI5634PCI/4/8 User Guide 1 8 . To view the COM ports, click Control Panel and double-click System . The System Properties dialog box appears. The MultiTech PCI ISI Card is located under Multi Port Adapter . Click Ports (COM & LPT) to view the ports.
47 Chapter 3 — Software/Driver Installation Installing Modems to COM Ports in Win 95 /98/Me 1 . Click Start , Settings , Control Panel , and then double-click the Modems icon. I n the General tab, click Add . 2 . The Install New Modem dialog box will appear.
48 ISI5634PCI/4/8 User Guide 3 . The Install New Modem - Manufacturers dialog box appears. In the Manufacturers list, scroll down and highlight "MultiTech Systems." In the Models list, highlight the modem type used on the ISI board. Highlight "ISI5634PCI-8 PCI 56K Modem" and click Next .
49 Chapter 3 — Software/Driver Installation 5. When installing the first ISI modem, the Location Information screen will appear (it does not appear when additional modems or terminal adapters are installed). Fill in the appropriate area code and phone number information.
50 ISI5634PCI/4/8 User Guide 7 . Return to the General tab to view COM port assignments (and make changes if necessary). 8 . Click Add and repeat installation steps 27 to install modems (one at a time) to the last three modem ports of the ISI5634PCI-4, OR to the last seven modem ports of the ISI5634PCI-8.
51 Chapter 3 — Software/Driver Installation Removing the ISI5634PCI Driver (Windows 95/98/Me) 1 . Click Settings , Control Panel , and then double-click Add/Remove Programs . 2 . From the list box, select MultiTech ISI Driver Device . 3 . Click Add/Remove and follow screen instructions.
52 ISI5634PCI/4/8 User Guide If you have downloaded the ISI driver from the MultiTech web site onto a diskette, use this command: COPY A:NOVELLAIOISIX.
53 Chapter 3 — Software/Driver Installation This present installation section is task-oriented with minimal explanation of procedural steps. The section Multi-Tech Installation Script, which immediately follows this section, presents additional details to aid in installation.
54 ISI5634PCI/4/8 User Guide 4. Copy the untarred (inflated or non-compressed) files to a floppy disk # cd /isi/unifiedinstimg301 #scosh - Select Manager . - Select Archive . - Select Create . - Press space bar to highlight tmp/ and usr/ directories. - Press <ENTER> to copy.
55 Chapter 3 — Software/Driver Installation 5. Select as the Media Device Floppy Disk Drive. 6. Select Continue . 7. Highlight Multi-Tech ISA/PCI ... and select Install . 8. Enter Y (yes) to continue installing the ISI driver. 9. As many as four ISI cards can be installed in the server.
56 ISI5634PCI/4/8 User Guide 1. This text appears on the screen: You can install up to 4 ISA/PCI cards in a system. The PCI cards will be autodetected on bootup [ISI5634PCI is a PCI card, i.e., it has a PCI bus]. Enter the number of ISA cards you want to install and configure on your system (0-4): Select 0 if your computer has a PCI bus.
57 Chapter 3 — Software/Driver Installation ISICOM. The default prefix for the tty ports is ttyl. The default prefix for the printer is prnl. Is this acceptable? (y/n/ q). For most users, its best to select y , which entails accepting the default values.
58 ISI5634PCI/4/8 User Guide printing). Specify a unique printer base name (printer parameters are outlined in the Multi_Setup Utility section in this manual ). Printer base name selected: _________________ When you have specified the device base name and the printer base name, press ENTER to continue.
59 Chapter 3 — Software/Driver Installation Activating Ports in SCO Open Server 5 SCO Open Server 5 provides a device database that monitors the activity of serial ports through which users can log onto the host. If your ISI ports are used by terminals (e.
60 ISI5634PCI/4/8 User Guide 5 . Repeat this command for each port you want to activate, using the lower case letter for local terminal use or upper case for modem control. Note: Only one of the options (e.g., modem control or local terminal access) should be enabled for any port at one time.
61 Chapter 3 — Software/Driver Installation issued from time to time. The 'make' utility, GNU C compiler, and the kernel sources need to be installed on your system. If any of these are missing, the compilation will fail. Most later Linux OSs install these elements automatically .
62 ISI5634PCI/4/8 User Guide NOTE: To read from a DOS formatted floppy, a kernel with support for the FAT file system (either statically linked in the kernel or as modules) is required. Steps for copying the driver from a floppy: 1. Linux floppy disks are in ext2 format.
63 Chapter 3 — Software/Driver Installation To view busy IRQs, enter: cat /proc/interrupts You must load the driver before you can load the firmware.
64 ISI5634PCI/4/8 User Guide first port on the first card). Save the configuration for a particular port using the 'save setup as' menu option as, for example, '1a' for the port / dev/ttyM1a. To connect to the port /dev/ttyM1a using minicom the next time, ' minicom 1a ' needs to be executed.
65 Chapter 3 — Software/Driver Installation - /dev/ttyM4a TO /dev/ttyM4h for the fo urth card Devices mapped for modem cards (ISI5634PCI-4 and ISI5634PCI-8 cards): For ISI5634PCI-4 cards (4 ports): - /dev/ttyM1a to /dev/ttyM1d for modem ports. For ISI5634PCI-8 cards (8 ports): - /dev/ttyM1a to /dev/ttyM1h for modem ports .
66 ISI5634PCI/4/8 User Guide Note: A base I/O address of 0, e.g., ISIBaseX=oxo, or omission of these parameters for any card X, disables that particular card. Miscellaneous: Device files corresponding to ports on the ISI5634PCI cards are created in the /dev folder .
67 Chapter 3 — Software/Driver Installation rm ttyM1 * rm ttyM2 * rm ttyM3 * rm ttyM4 * RedHat Linux 6.2/7.0 RPM Drivers for ISI5634PCI-4/8 Server Cards This installation procedure applies only to RedHat Linux versions 6.
68 ISI5634PCI/4/8 User Guide 3. List the RPM files on the CD-ROM using this command: ls LINUX-RPM: Copying the driver from a floppy The ISI driver .rpm file can be copied from a DOS formatted floppy using the 'mcopy' command if the 'mtools' have been installed.
69 Chapter 3 — Software/Driver Installation RPM, you will need to use the --force option in the RPM command as in step 5b below. 5a. For RPM version 6.2: Copy the RPM to a temporary folder. In this example, well use /isi. Installation is in three parts, building the isicom-smp.
70 ISI5634PCI/4/8 User Guide LINUX-RPM: Verifying the ports To test the installation, you can use the terminal program minicom. Use the command minicom -s to set up the tty port that you will use to communicate. 1. In the Configuration window, select Serial Port Setup.
71 Chapter 3 — Software/Driver Installation For the ISI5634PCI-8, it uses the following: - /dev/ttyM1a TO /dev/ttyM1h for the first card - /dev/ttyM2a TO /dev/ttyM2h for the second card - /dev/ttyM3.
72 ISI5634PCI/4/8 User Guide HOWTO) explains in detail the procedure for configuring a Linux machine as a PPP server. This information is also available at http://www.interweft.com.au/other/ppp-howto/ppp-howto.html. The documentation in the PPP-HOWTO is directly applicable to ISI ports.
73 Chapter 3 — Software/Driver Installation To load a custom configuration that was saved using the &W command, use ATZ . Note that the Z command must be in a command string by itself. For a Macintosh, the initialization should include the &D0 command.
74 ISI5634PCI/4/8 User Guide References ISI5634PCI User Guide The ISI5634PCI Quick Start Guide is a condensed version of this User Guide in printed form. It is especially intended for use during installation. The Quick Start Guide is also on the ISI CD-ROM.
Chapter 4 AT Commands, S-Registers, & Result Codes.
76 ISI5634PCI/4/8 User Guide AT Commands AT commands are used to control the operation of your modem. They are so called because each command must be preceded by the characters AT to get the AT tention of the modem. AT commands can be issued only when the modem is in command mode or online command mode.
77 Chapter 4 — AT Commands, S-Registers, Result Codes connecting to another modem. For a table of valid result codes, see Result Codes at the end of this chapter. You can issue several commands in one line, in what is called a command string . The command string begins with AT and ends when you press ENTER.
78 ISI5634PCI/4/8 User Guide Command: C n Carrier Control Values: n = 1 Default: 1 Description: C0 Transmit carrier always off. (Not supported.) C 1 Normal transmit carrier switching (included for back- ward compatibility with some software).
79 Chapter 4 — AT Commands, S-Registers, Result Codes Command: DS= y Dial Stored Telephone Number Values: n = 03 Default: none Description: Dial a number previously stored in directory number y by the &Zy=x command.
80 ISI5634PCI/4/8 User Guide I 1 1 Display diagnostic information for the last modem con- nection, such as DSP and firmware version, link type, line speed, serial speed, type of error correction/data compression, number of past retrains, etc.
81 Chapter 4 — AT Commands, S-Registers, Result Codes Command: S r = n Set Register Value Values: r = S-register number; n varies Default: None Description: Set value of register S r to value of n , where n is entered in decimal format. E.g., S0=1 .
82 ISI5634PCI/4/8 User Guide Command: X n Result Code Selection Values: n = 0 7 Default: 4 Description: X 0 Basic result codes ( e.g., CONNECT ); does not look for dial tone or busy signal. X 1 Extended result codes ( e.g., CONNECT 46000 V42bis ); does not look for dial tone or busy signal.
83 Chapter 4 — AT Commands, S-Registers, Result Codes Command: &C n Data Carrier Detect (DCD) Control Values: n = 0 or 1 Default: 1 Description: & C 0 Forces the DCD circuit to be always high. & C 1 DCD goes high when the remote modems carrier signal is detected, and goes low when the carrier signal is not detected.
84 ISI5634PCI/4/8 User Guide Command: &J n Auxiliary Relay Control Values: n = 0 Default: 0 Description: & J 0 The auxiliary relay is never closed. & J 1 Not supportedresponds ERROR . Command: &K n Flow Control Selection Values: n = 0, 3, or 4 Defaults: 3 Description: & K 0 Disable flow control.
85 Chapter 4 — AT Commands, S-Registers, Result Codes Command: &T n V.54 Test Commands Values: n = 0 , 1 , 3 o r 6 Default: None Description: & T 0 Abort. Stop any test in progress. & T 1 Local analog loopback test. & T 3 Local digital loopback test.
86 ISI5634PCI/4/8 User Guide Command: &Zy =x Store Dialing Command Values: y = 03 (callback security disabled) or 029 (callback security enabled) x = Dialing command Default: None Description: Stores dialing command x in memory location y . Dial the stored number using the command ATDS=y .
87 Chapter 4 — AT Commands, S-Registers, Result Codes Command: K n Break Control Values: n = 05 Default: 5 Description: Controls the response of the modem to a break received from the computer, the remote modem, or B command. Response is different for each of three different states.
88 ISI5634PCI/4/8 User Guide Command: N n Error Correction Mode Selection Values: n = 05, or 7 Default: 3 Description: N 0 Non-error correction mode with data buffering (buffer mode; same as &Q6 ). N 1 Direct mode. N 2 MNP reliable mode. If the modem cannot make an MNP connection, it disconnects.
89 Chapter 4 — AT Commands, S-Registers, Result Codes Description: V 0 Disable the appending of the protocol result code to the DCE speed. V 1 Enable the appending of the protocol result code to the DC E speed.
90 ISI5634PCI/4/8 User Guide % D C 1 The modem ignores AT commands. Note: The modem responds to AT%DC for 10 seconds after power-up. Command: %E n Fallback and Fall Forward Control Values: n = 0, 1, or 2 Default: 2 Description: % E 0 Disable fallback and fall forward.
91 Chapter 4 — AT Commands, S-Registers, Result Codes Command: #CBD n Callback Delay Values: n = 0255 Default: 1 5 Description: Sets the length of time (in seconds) that the mod em waits before calling back the remote modem.
92 ISI5634PCI/4/8 User Guide #CBP0 N o parity. #CBP1 Odd parity. #CBP2 Even parity. Command: #CBRy Callback Security Reset Values: y = 029 Default: None Description: Clears password &phone number in y memory location. Command: #CBS n Callback Enable/Disable Values: n = 0, 1, 2, or 3 Default: 0 Description: #CBS0 D isable callback security.
93 Chapter 4 — AT Commands, S-Registers, Result Codes to ten command character. Then press ENTER. Used mostly to issue hangup command: +++ATH<cr> . Command: %%%AT<cr>R e m ote Configuration Escape Sequence Values: n / a Description: Initiates remote configuration mode while online with remote modem.
94 ISI5634PCI/4/8 User Guide About DTMF DTMF (dual tone multi frequency) is the signal to the phone company that you generate when you press an ordinary telephones touch keys. In the United States and perhaps elsewhere, its known as Touchtone phone (formerly a registered trademark of AT&T).
95 Chapter 4 — AT Commands, S-Registers, Result Codes Dual Tone Multi-frequency (DTMF) was a technique proposed by the phone company to replace pulse dialing to make dialing faster and more reliable. In anticipation to adding other customer services, 6 additional digits were included, totaling 16 digits.
96 ISI5634PCI/4/8 User Guide S5 decimal 032 8 ( ^ H) Sets ASCII code for the backspace 33127 character. Values greater than 32 disable backspace. S6 seconds 265* 2* Sets time the modem waits after it goes off-hook before it begins to dial the telephone number.
97 Chapter 4 — AT Commands, S-Registers, Result Codes which the modem attempts to connect. 0 = maximum modem speed 1 = reserved 2 = 1200/75 bps 3 = 300 bps 4 = reserved 5 = 1200 bps 6 = 2400 bps 7 =.
98 ISI5634PCI/4/8 User Guide 12 = 52000 bps 13 = 54000 bps 14 = 56000 bps S42 decimal 0 1 1 Enables/disables the 56K auto rate. When 56K auto is disabled, fallback to V.34 is also disabled. 0 = disable; 1 = enable. S43 decimal 0 1 1 For testing and debugging only.
99 Chapter 4 — AT Commands, S-Registers, Result Codes Result Codes In command mode, ISI5634PCI modems can send responses called result codes to your computer.
100 ISI5634PCI/4/8 User Guide 7 8 * CONNECT 48000 Connected at 48000 bps, 56K rate 7 9 * CONNECT 50000 Connected at 50000 bps, 56K rate 8 0 * CONNECT 52000 Connected at 52000 bps, 56K rate 8 1 * CONNE.
Chapter 5 W ar r anty , Ser vice, and T ech Suppor t.
102 ISI5634PCI/4/8 User Guide Software User License Agreement The ISI drivers and firmware are licensed by Multi-Tech Systems, Inc. to the original end-user purchaser of the product, hereafter referred to as Licensee . The License includes the distribution diskette, other accompanying programs, and the documentation.
103 Chapter 5 — Warranty, Service, and Tech Support Licensee agrees to implement sufficient security measures to protect Multi-Tech Systems, Inc. proprietary interests and not to allow the use, copying or transfer by any means, other than in accordance with this agreement.
104 ISI5634PCI/4/8 User Guide Limited Warranty Multi-Tech Systems, Inc. ( MTS ) warrants that its products will be free from defects in material or workmanship for a period of two years from the date of purchase, or if proof of purchase is not provided, two years from date of shipment.
105 Chapter 5 — Warranty, Service, and Tech Support Tech Support Multi-Tech has an excellent staff of technical support personnel available to help you get the most out of your Multi-Tech product. If you have any questions about the operation of this unit, call 1-800- 972-2439.
106 ISI5634PCI/4/8 User Guide Service If your tech support specialist decides that service is required, your unit may be sent (freight prepaid) to our factory. Return shipping charges will be paid by Multi-Tech Systems. Include the following with this product: A description of the problem.
Appendices.
108 ISI4608 Owner's Manual Appendix ARegulatory Information FCC Regulations for Telephone Line Interconnection 1 . This equipment complies with part 68 of the Federal Communications Commission Rules. On the outside surface of this equipment is a label that contains, among other information, the FCC registration number.
109 Appendix A - Base I/O Address Switch Settings operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make necessary modifications in order to maintain uninterrupted service.
110 ISI4608 Owner's Manual Class A Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
111 Appendix A - Base I/O Address Switch Settings Canadian Limitations Notice: Ringer Equivalence Number Notice: The ringer equivalence number (REN) assigned to each terminal device provides an indica.
112 ISI4608 Owner's Manual Fax Branding Statement The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machin.
113 Appendix A - Base I/O Address Switch Settings New Zealand Telecom Warning Notice Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition.
114 ISI4608 Owner's Manual.
Index.
116 ISI5634PCI/4/8 User Guide Index Symbols 11-bit mode 90 56K operation digital loss when used with PBX 98 disabling the auto rate 98 maximum connect speed 97 A abort timer 96 activating ports in SCO.
117 Index Q8 0 S= 81 S? 81 T8 1 V8 1 W8 1 X8 2 Y8 2 Z8 2 autoanswer 76, 9 5 Auxiliary Relay Control command 84 B backspace character, setting 96 base I/O address 10 baud rates 10 Bell 212A mode 77 bla.
118 ISI5634PCI/4/8 User Guide Data Carrier Detect command 83 Data Compression Control com- mand 89 data mode 76, 80 Data Set Ready Control command 8 4 Data T erminal Ready command 8 3 DCD Control comm.
119 Index installation activating ports in SCO Open Server 5 59 hardware 12 ISI5634PCI driver in Linux 60 in Netware 51 in SCO 52 in Windows 2000 18 in Windows 95/98/Me 42 in Windows NT 33 modems to C.
120 ISI5634PCI/4/8 User Guide modem install Linux 64 Linux RPM 70 Netware 52 SCO 59 Windows 2000 26 Windows 95/98/Me 47 Windows NT 37 Modem Port Flow Control com- mand 86 Modem Reset command 82 modems.
121 Index Result Codes Enable/Disable com- mand 80 retrain 82 Return Online to Data Mode com- mand 80 rings, setting number of 95 ROM checksum 79 S S-registers 95113 reading 81 S0 95 S1 95 S10 96 S.
122 ISI5634PCI/4/8 User Guide T tech support 105 technical specifications 10 temperature 10 testing the modem 85 T one Dialing command 81 tones, dialing 96 Transmit Break command 86 U uninstall ISI driver Linux 66 Linux RPM 72 Netware 52 SCO 60 Windows 2000 31 Windows 95/98/Me 51 Windows NT 42 V V .
Ein wichtiger Punkt beim Kauf des Geräts Multi-Tech Systems ISI5634PCI/4/8 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Multi-Tech Systems ISI5634PCI/4/8 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Multi-Tech Systems ISI5634PCI/4/8 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Multi-Tech Systems ISI5634PCI/4/8 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Multi-Tech Systems ISI5634PCI/4/8 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Multi-Tech Systems ISI5634PCI/4/8 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Multi-Tech Systems ISI5634PCI/4/8 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Multi-Tech Systems ISI5634PCI/4/8. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Multi-Tech Systems ISI5634PCI/4/8 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
