Benutzeranleitung / Produktwartung XD3500U des Produzenten Mitsubishi
Zur Seite of 53
XD3500 This User Manual is important to you. Please r ead it befor e using your pr ojector . DLP™ PROJECTOR MODEL XD3500U User Manual.
EN-2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE P ARTS INSIDE REFER SERVICING TO QUALIFIED SER VICE PERSONNEL.
EN-3 Contents Important safeguards ........................................................................................................................ 4 Preparing your pr ojector ...................................................................
EN-4 Important safeguar ds Please read all these instructions r egar ding your projector and r etain them for futur e refer ence. Follow all warnings and instructions marked on the projector . 1. Read instructions All the safety and operating instructions should be read befor e the appliance is operated.
EN-5 Important safeguards (continued) WARNING: Unplug immediately if there is something wrong with your pr ojector . Do not operate if smoke, strange noise or odor comes out of your projector . It might cause fi re or electric shock. In this case, unplug immediately and contact your dealer .
EN-6 Pr eparing your pr ojector 1 2 3 Checking accessories The following accessories are pr ovided with this pr ojector . Check to be sure that all of the accessories ar e packed in the package.
EN-7 Overview 5 6 3 4 1 2 9 10 7 8 5 4 7 10 6 9 11 8 1 2 3 1 Control ar ea 2 Speaker 3 Air outlet grille 4 Lens 5 Remote control sensor (fr ont) 6 Air inlet grille 7 Remote control sensor (r ear) 8 La.
EN-8 1 Preparing your projector (continued) Bottom side 1 Adjustment feet 31 COMPUTER HDMI VIDEO KEYSTONE AUTO POSITION DVI-D(HDCP) S-VIDEO FREEZE MAGNIFY AV MU TE PAG E UP HOME PAG E DO WN END 1 2 P .
EN-9 Using the r emote contr ol 30° 30° 30° 30° 20° 10° 20° 10° 20° 20° Operational range of the r emote contr ol • Keep the remote contr ol photo-sensor out of dir ect sunlight or fl uor escent lamp light. • Keep the remote contr ol photo-sensor at least 2 m (6 feet) away from fl uor escent lamps.
EN-10 Setting up your pr ojector Setting up the scr een Install the screen perpendicularly to the pr ojector . If the screen can not be installed in such a way , adjust the projection angle of the pr ojector .
EN-11 Setting up your pr ojector (continued) Adjusting the position of the pr ojected image T o adjust the positions of the projector and the screen, use LENS SHIFT button. 1. Press the LENS SHIFT button. • The LENS SHIFT menu appears at the center of the screen.
EN-12 Setting up your pr ojector (continued) Fr ont pr ojection, ceiling mounting For ceiling mounting, you need the ceiling mount kit designed for this projector .
EN-13 2 1 Viewing computer images 2 1 AUDIO OUT AUDIO IN-1/2 2 1 A. Connecting the pr ojector to a computer Preparation: • Make sure that the power of the pr ojector and that of the computer ar e turned off. • When connecting the projector to a desktop computer , disconnect the RGB cable that is connected to the monitor .
EN-14 Viewing computer images (continued) 1. Plug the attached power cord into the power cor d inlet of this projector . 2. Plug the other end of the power cord into a power outlet. • One of power cords for the U.S., Eur ope and U.K. is pr ovided appropriately .
EN-15 C. Installing the terminal cover This projector includes a terminal cover . If necessary , install the terminal cover to the projector . 1. Fit two hooks of the terminal cover into the projector . 2. Tighten the attachment screws (a) fi rmly . Important: • Don’t carry the pr ojector by the terminal cover .
EN-16 Viewing computer images (continued) D. Pr ojecting images Preparation: • Remove the lens cap. POWER button COMPUTER/ DVI-D button COMPUTER 1, 2 buttons LENS SHIFT button POWER button ZOOM/FOCU.
EN-17 Viewing computer images (continued) 9. Press the ZOOM/FOCUS button to display the ZOOM/FOCUS menu. 10. Adjust with the S or T button to get an approximate size. • When the ENTER button is pressed while the ZOOM/FOCUS menu is displayed, the adjustment mode is switched between F AST and STEP .
EN-18 A V mute The video and audio signals are temporarily muted when the A V MUTE button is pressed. T o cancel muting, press the A V MUTE button again.
EN-19 Viewing video images Connecting to a video player , etc. 1. Connect one end of a commercially available video cable to the VIDEO IN terminal of the projector . 2. Connect the other end of the video cable to the video output terminal of the video equipment.
EN-20 Viewing video images (continued) Projector + DVD player or HDTV decoder Some DVD players have an output connector for 3-line fi tting (Y , C B , C R ). When connecting such DVD player with this projector , use the COMPUTER/COMPONENT VIDEO IN-2 terminals.
EN-21 Connection (for video equipment having a DVI-D terminal) Equipment having a DVI-D terminal Audio cable (option) T o DVI-D terminal DVI cable (option) COMPUTER/COMPONENT VIDEO DVI-D IN (HDCP) T o audio output terminals AUDIO DVI-D • For connection to the DVI-D terminal, use a commercially available DVI cable.
EN-22 Viewing video images (continued) D. Pr ojecting images Preparation: • Remove the lens cap. POWER button COMPUTER/ DVI-D button COMPUTER 1, 2 buttons LENS SHIFT button POWER button ZOOM/FOCUS b.
EN-23 7. Adjust the position of the projector to keep an appr opriate pr ojection distance with which images ar e projected in their specifi ed sizes. 8. Adjust the position of the projector so that the pr ojector and the scr een ar e perpendicular to each other .
EN-24 V olume from the speaker Press the VOLUME + or - button to change the volume fr om the speaker . The volume control bar will appear on the scr een. VOLUME 15 • The volume control bar will disappear about 10 seconds after the VOLUME button is r eleased.
EN-25 Menu operation Y ou can make various settings using the displayed menus. Menu display mode and menu type There ar e two menu display modes: QUICK MENU mode and DET AIL MENU mode.
EN-26 Basic pr ocedur e for setting the menus 1. Press the MENU button. • The menu selection bar is displayed in the QUICK MENU mode. QUICK MENU Selectable menus are displayed by icons. (The menu icon being selected is displayed on a blue background.
EN-27 Settings of each menu item Menus displayed in the QUICK MENU mode QUICK MENU NORMAL ASPECT LAMP MODE ST ANDARD QUICK MENU CONTRAST BRIGHTNESS 0 0 ST ANDARD COLOR 0 COLOR COLOR TEMP .
EN-28 Menus displayed in the QUICK MENU mode and the DET AIL MENU mode INFORMA TION menu INFORMA TION LAMP TIME (LOW) INPUT RESOLUTION VERTICAL FREQUENCY HORIZONT AL FREQUENCY SYNC.
EN-29 Menus displayed in the DET AIL MENU mode IMAGE menu IMAGE opt. CONTRAST BRIGHTNESS 0 0 ST ANDARD 0 0 COLOR TINT COLOR TEMP . 0 SHARPNESS AUTO COLOR ENHANCER OK ADVANCED MENU IMAGE ADV ANCED MENU opt.
EN-30 INSTALLATION menu INST ALLA TION opt. LAMP MODE OFF AUTO POWER ON ST ANDARD ST ANDBY MODE ST ANDARD ON SPLASH SCREEN ON AUTO POWER OFF OFF BACK COLOR BLUE OFF IMAGE REVERSE BLACK AV MUTE MODE IMAGE CAPTURE GO LENS LOCK OK INST ALLA TION LENS LOCK opt.
EN-31 FEA TURE menu FEA TURE NORMAL opt. MENU POSITION VIDEO SIGNAL ? ASPECT RESET ALL English LANGUAGE A Ë OK SCART INPUT DISPLA Y INPUT P ASSWORD FUNCTION CINEMA MODE 1. SETUP AUTO OFF AUTO AUTO ITEM SETTING FUNCTION ASPECT NORMAL Select to change the aspect ratio automatically depending on the input signal.
EN-32 SIGNAL menu USER 1 CLAMP WIDTH CLAMP POSITION 1 LPF OFF SHUTTER(U) 0 SHUTTER(L) 0 VERT . SYNC AUTO ? SHUTTER(LS) 0 SHUTTER(RS) 0 SIGNAL opt. SIGNAL VERTICAL FREQUENCY HORIZONT AL FREQUENCY 75.04 Hz HORIZ. PIXELS 1024 60.02 KHz CANCEL opt. OK OK EXECUTE 768 VERT .
EN-33 Adjusting pr ojected images T o adjust the brightness (CONTRAST and BRIGHTNESS): Y ou can make adjustments for the brightness of the projected image using the menu. (See page 26 for menu setting.) 1. Display the QUICK MENU or IMAGE menu. 2. Select CONTRAST or BRIGHTNESS by pressing the S or T button.
EN-34 T o cancel the menu: 7. Press the MENU button. T o enable the stored color temperature: 1. Set COLOR TEMP . to USER in the QUICK MENU or set it to USER in the IMAGE menu. About color temperature There ar e different kinds of white color . Color temperature is a way to show the differ ences in white.
EN-35 Adjusting pr ojected images (continued) How to adjust the computer image This projector automatically selects a pr oper signal format according to the type of video signal supplied from the computer . However , video signals from the computer may not be projected corr ectly depending on the types of the computer and images to be projected.
EN-36 How to adjust the image supplied from the computer using the menu: Carry out the following procedur es according to the symptoms. Wide strips appear . ……………………………………… Adjust TRACKING in the SIGNAL menu. The projected image fl ickers.
EN-37 Setting of the image displayed during startup or muting Y ou can display your desired image as the startup screen (or splash scr een). Using the menu, you can also use such image as a background that is displayed while the video is muted or no signal is supplied.
EN-38 Passwor d function This projector is equipped with the passwor d function that is designed for prevention of wr ong operation by children and r estriction on operation by other than specifi ed users. The passwor d function has 3 modes as follows.
EN-39 Pictur e in Pictur e (PinP) One of the special features of this pr ojector is the picture-in-pictur e (PinP) mode. The PinP mode allows you to view the images from dif ferent sources at the same time.
EN-40 Mouse r emote contr ol By connecting to personal computer through the USB port, you can operate your computer with the pr ojector remote control.
EN-41 Supervising and contr olling by computer Y ou can supervise and control the projector’ s operation using a personal computer via a LAN network. • T o supervise and control the projector , install the software “Projector -Control Device Installer *” contained in the attached CD-ROM.
EN-42 Indicators This projector has 2 indicators, each of which shows the operation condition of the pr ojector . The following offer solutions to possible pr oblems.
EN-43 Replacing the lamp This projector is equipped with a lamp to pr oject images. This lamp is a consumable. It may bur n out or its brightness may decrease during use. In such cases, r eplace the lamp with a new one as soon as possible. Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector .
EN-44 Replacing the lamp (continued) T o replace the lamp: 1. T urn off the main power switch and unplug the power cord. 2. Loosen the screw (a) using a Phillips scr ewdriver (+), and remove the lamp cover (b). (a) (b ) 3. Loosen the screws (c) using a Phillips scr ewdriver (+).
EN-45 When removing the lamp fr om the ceiling-mounted projector When removing the lamp fr om the ceiling-mounted projector , use the lamp replacement tray packed with the projector or option lamp to pr event glass fragments from scattering. • Assemble the lamp replacement tray accor ding to the procedure shown on it.
EN-46 T roubleshooting Before asking for r epair of the projector , check the following. If the symptom persists, stop using the projector , be sure to unplug the power plug, and then contact your dealer . No image appears on the screen. Problem Solution Power can not be turned on.
EN-47 T roubleshooting (continued) No image appears on the screen. (continued) Problem Solution “NO SIGNAL” is displayed. • T ur n on the power of the connected device, or check whether ther e is something wrong with the connected device. • Check whether the external device output signals.
EN-48 T roubleshooting (continued) Images are not displayed corr ectly . (continued) Problem Solution Differ ent color tint. • When comparing images projected by two pr ojectors, tints in the displayed images may be differ ent because of variation between their optical components.
EN-49 T roubleshooting (continued) If the following problem occurs after the lamp is r eplaced, check the following fi rst. Problem Solution The projector does not turn on. • Fit the lamp cover securely . (See pages 43 and 44.) • Reset the lamp operating time.
EN-50 Specifi cations The specifi cations and outside appearance of the pr ojector are subject to change without prior notice. T ype DLP™ projector Model XD3500U Display technology 0.7-inch Single chip DMD Pixel 1024 x 768 = 786432 pixels Projection lens F 2.
EN-51 Specifi cations (continued) Specifi cation of RGB signals in each computer mode of the pr ojector Signal mode Resolution (H x V) Horizontal frequency (kHz) V ertical frequency (Hz) Normal mode (H x V) TV60, 480i (525i) 720 x 480 15.73 59.94 1024 x 768 *1 TV50, 576i (625i) 720 x 576 15.
EN-52 450 187 101* 373 Dimension drawings (unit: mm) Specifi cations (continued) Specifi cation of RGB signals in each computer mode of the projector (continued) Important: • Some computers aren’ t compatible with the projector . • The projector’ s maximum resolution is 1024 x 768 pixels.
1 Zusho Baba, Nagaokakyo-City , Kyoto Japan M I T SUBIS HI ELECTRIC CORPORA T I O N A.
Ein wichtiger Punkt beim Kauf des Geräts Mitsubishi XD3500U (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mitsubishi XD3500U noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mitsubishi XD3500U - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mitsubishi XD3500U reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mitsubishi XD3500U erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mitsubishi XD3500U besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mitsubishi XD3500U verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mitsubishi XD3500U. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mitsubishi XD3500U gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
