Benutzeranleitung / Produktwartung PD-5030 des Produzenten Mitsubishi Electronics
Zur Seite of 52
Mitsubishi Plasma Display PD-5030 & PD-6130 Owner’ s Guide T echnically Anything is Possible ®.
.
IMPOR T ANT SAFETY INSTRUCTIONS (PD-5030/PD-6130) Read before operating equipment 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this plasma display near water . 6. Clean only with a dry cloth.
Impor tant Infor mation Precautions Please read this manual carefully before using your Mitsubishi plasma monitor and keep the manual handy for future reference. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CA UTION: T O REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER.
NO TE: When you connect a computer to this monitor , attach the supplied ferrite cores. If you do not do this, this monitor will not conform to mandatory FCC standards. Attaching the ferrite cores: Set the ferrite cores on both ends of the MONITORLINK™ cable (not supplied), and both ends of the po wer cable (supplied).
The normal use of a TV should include a mixtur e of TV picture types. The most frequentl y used picture types should fill the screen with constantly mo ving images rather than stationary images or patterns.
Cleaning Safeguards Plasma Display Screen & Cabinet Please follo w the cleaning safeguards listed belo w to pre vent damage to your Plasma Display and retain this document for future reference. IMPOR T ANT : No Abrasives! DO NO T use any kind of abr asive cloth or cleaner or ammonia on the Plasma Displa y’ s screen or cabinet.
Introduction Introduction to the PD-5030/ PD-6130 Plasma Monitors Mitsubishi’ s PD-5030/PD-6130 plasma displays are a seamless blend of cutting-edge visual technology and sophisticated design. The monitor’ s sleek techno-art lines blend in well with your en vironment.
How to Attach Options to the Plasma Monitor .... 1 V entilation r equirements for enclosure mounting ........... 1 How to use the safety metal fittings and the screws for safety metal fittings ................................................. 1 Part Names and Function .
1 50 mm (2") 50 mm (2") 50 mm (2") Wal l Wal l 50 mm (2") 50 mm (2") Y ou can attach your optional mounts or stand to the plasma monitor in one of the follo wing two ways: * While it is upright. (See Drawing A) * As it is laid down with the screen face down (See Drawing B).
2 q PO WER T urns the monitor’ s po wer on and off. w REMO TE SENSOR WINDO W Receives the signals from the remote control. e PO WER/ST ANDBY indicator When the power is on ............................. Lights green. When the power is in the standby mode .
3 Rear View/ T erminal Board A AC I N Connect the included power cord here. B EXT SPEAKER L and R Connect speakers (optional) here. Maintain the correct polarity . Connect the (positi ve) speaker wire to the EXT SPEAKER terminal and the (negati v e) speaker wire to the EXT SPEAKER terminal on both LEFT and RIGHT channels.
4 → VIDEO1 → VIDEO2 → VIDEO3 RGB / PC DVD / HD VIDEO ADJUST MENU / ENTER POINTER ZOOM SLEEP EXIT VOLUME MUTE FORMAT INFO AUTO POSITION POWER ON STANDBY RM-PDP2 Remote Control q PO WER ON/ST ANDBY Switches the pow er on/standby . (This does not operate when PO WER/ST ANDBY indicator of the main unit is off .
5 Battery Installation and Replacement Insert the 2 “AAA” batteries, making sure to set them in with the proper polarity . 1. Remove the remote control’ s back cov er by gently pressing the rigid tab in the direction of the arrow . 2. Install the batteries according to the (+) and (–) indication inside the case.
6 POWER/STANDBY Appro x. 7m / 23ft Using the wired remote control mode Connect one end of the remote cable to the remote control’ s REMO TE J A CK and the other end to the “REMO TE IN” terminal on the monitor . When the cable is connected, the mode automatically switches to wired remote control.
7 Installation VIDEO ( IN / OUT ) VIDEO 1 VIDEO 2 VIDEO 3 AUDIO 1 DVD 1 / HD 1 R ( MONO ) L Y Cb/ Pb Cr /Pr RGB 2 / DVD 2 / HD 2 RGB 1 R/ VD G/ B/ HD ( I N / OUT ) DV I ( Digital RGB ) AUDIO 2 R ( MON.
8 Connecting Y our PC or Macintosh Computer Connecting your PC or Macintosh computer to your plasma monitor will enable you to display your computer’ s screen image for an impressiv e presentation. The plasma monitor supports the signals described on page 40.
9 5 4 3 2 1 15 14 13 12 11 10 9 8 7 6 MonitorLink™ Connections MonitorLink and MonitorLink Contr ol 1. Connect a MonitorLink cable from the Mitsubishi Recei ver/Controller back panel to the plasma monitor back panel.
10 Note: 1. The VIDEO1 and RGB1 terminals can be used for either INPUT or OUTPUT . When LOOP OUT is ON, do not connect an OUTPUT signal fr om another unit, that will place an e xtraor dinary load on the other unit and may damage it. 2. LOOP OUT can not be turned ON while signals are input to RGB1 terminal.
11 Basic Operations POWER ON: 1. Plug the po wer cord into an acti ve A C power outlet. 2. Press the Power b utton located underneath the right side of the front panel. The monitor’ s POWER/ST ANDBY indicator turns green and the plasma display is on.
12 SLEEP/OFF TIMER T o set the off timer: The off timer can be set to tur n the power of f after 30, 60, 90 or 120 minutes. 1. Press the SLEEP b utton to start the timer at 30 minutes. 2. Press the SLEEP b utton to the desired time. 3. The timer starts when the menu turns of f.
13 EXP AND screen size The picture is expanded in the horizontal and v ertical direction, maintaining the original proportions. * Use this for theater size (wide) movies, etc. ZOOM screen size The squeezed film ima ge is expanded to fill the entir e screen at a ratio of 2.
14 Information Supported resolution See page 40 for details on the display output of the var ious VESA signal standards supported by the monitor . When 852 (848) dot 480 line wide V GA* signals with a vertical frequency of 60 Hz and horizontal frequency of 31.
15 Menu Operations The follo wing describes how to use the menus and the selected items. In the explanation, the menu section is shown close up. 1. Press the MENU/ENTER b utton on the remote control to display the MAIN MENU. MAIN MENU 2 / 2 MENU/ENTER EXIT PREVIOUS P AGE LANGU AGE COLOR SYSTEM SOURCE INFORMA TION SEL.
16 VIDEO Settings Menu Adjusting the picture The contrast, brightness, sharpness, color and tint can be adjusted as desired. Example: Adjusting the contrast 1. On the MAIN MENU, select “VIDEO SETTINGS”, then press the MENU/ENTER b utton. The “VIDEO SETTINGS” screen appears.
17 Reducing noise in the picture Use these settings if the picture has noise due to poor reception or when playing video tapes with poor picture quality . Example: Setting “NR-3” 1. On the MAIN MENU, select “VIDEO SETTINGS”, then press the MENU/ENTER b utton.
18 Changing the Gamma Curve This feature adjusts the brightness of the midtone areas while keeping shadows and highlights unchanged. Example: Setting “3” 1. On the MAIN MENU, select “VIDEO SETTINGS”, then press the MENU/ENTER b utton. The “VIDEO SETTINGS” screen appears.
19 ColorView™ Use this procedure to adjust hue and color density for red, green, blue, yello w , magenta and cyan. Y ou can accentuate the green color of trees, the blue of the sky , etc. Example: Adjusting the blue 1. On the MAIN MENU, select “VIDEO SETTINGS”, then press the MENU/ENTER b utton.
20 Setting the allocation of the audio connectors Setting the A UDIO 1, 2, and 3 connectors to the desired input. Example: Setting “AUDIO INPUT1” to “VIDEO 2” 1. On the MAIN MENU, select “ A UDIO SETTINGS”, then press the MENU/ENTER b utton.
21 2. Use the ▲ and ▼ b uttons to select “MENU”, then press the MENU/ENTER button. The “MENU” menu appears. 3. Use the ▲ and ▼ buttons to select “DISPLA Y MENU”. 4. T o set the DISPLA Y MENU to “OFF”... Use the and buttons to select “OFF”.
22 Setting the BNC connectors Select whether to set the input of the 5 BNC connectors to RGB or component. Example: Set the BNC INPUT mode to “COMP . ” 1. On the MAIN MENU, select “OPTION1”, then press the MENU/ENTER button. The “OPTION1” screen appears.
23 Setting high definition images to the suitable screen size Use this procedure to set whether the number of vertical lines of the input high definition image is 1035 or 1080. Example: Setting the “1080B” mode to “1035I” 1. On the MAIN MENU, select “OPTION1”, then press the MENU/ENTER button.
24 Resetting to the default values Use this operation to restore all the settings (PICTURE, A UDIO, IMAGE ADJUST , OPTION1~3, etc) to the factory default v alues. 1. On the MAIN MENU, select “OPTION1”, then press the MENU/ENTER button. The “OPTION1” screen appears.
25 Power management mode On Off Turning the picture back on Picture already on. Operate the keyboard or mouse. The picture reappears. POWER/ STANDBY indicator Green Red Power management operating status Not activated. Activated. Description Horizontal and vertical synchronizing signals are present from the computer .
26 ORBITER ORBITER - Une ven phosphor aging/b urn-in reduction feature. T o minimize the risk of unev en phosphor aging/ burn-in when displaying still images, the Mitsubishi PD- 5030 and PD-6130 of fers a built-in feature kno wn as ORBITER. The ORBITER feature intermittently shifts the screen image horizontally and vertically in small increments.
27 Setting the time for INVERSE/WHITE Set a time duration. Example: Set the INVERSE mode to star t in 2 hours and proceed f or one and a half hours. 1. On the Main Menu, select “OPTION 2”, then press the MENU/ENTER button. The “OPTION 2” screen appears.
28 Setting the gray level for the sides of the screen Use this procedure to set the gray level for the parts on the screen on which nothing is displayed when the screen is set to the 4:3 size. Example: Adjusting the “GRA Y LEVEL ” 1. On the MAIN MENU, select “OPTION2”, then press the MENU/ENTER button.
29 Setting the signal and blac k level f or D VI signal Choose the signal for the DVI connector (PC or STB/ DVD) and set the black level. Example: Setting the “PLUG/PLA Y” mode to “STB/ DVD” 1. On the MAIN MENU, select “OPTION2”, then press the MENU/ENTER button.
30 Option3 Settings Menu Using the timer This function sets the monitor to turn ON/OFF automatically at a set time. 1. On the MAIN MENU, select “OPTION3”, then press the MENU/ENTER button. The “OPTION3” screen appears. 2. Use the ▲ and ▼ buttons to select “TIMER”, then press the MENU/ENTER button.
31 INPUT ..................... Set the input mode that will be displayed when the timer is on. FUNCTION ............. Set the LONG LIFE function. T o reset the program 1. Align the cursor with the D A TE field that you wish to reset. 2. Using / b uttons, select “–”.
32 Information PWR. ON MODE settings LAST .......................... Last mode (the mode that was last selected at the time the po wer was switched of f). VIDEO1, 2, 3 ............. VIDEO input mode. RGB1, 2, MONLINK .. RGB input mode. HD/D VD1, 2 .
33 Loop Out setting When this feature is set to ON, the received signal will be looped out. Example: Setting “ON” 1. On the MAIN MENU, select “OPTION3”, then press the MENU/ENTER button. The “OPTION3” screen appears. 2. Use the ▲ and ▼ buttons to select “LOOP OUT”.
34 Color System Settings Menu Setting the video signal format Use these operations to set the color systems of composite video signals or Y/C input signals. Example: Setting the color system to “3.58 NTSC” 1. On the MAIN MENU (NEXT P A GE), select “COLOR SYSTEM”, then press the MENU/ENTER button.
35 RS-232C Control Application These specifications co ver the communications control of the plasma monitor by external equipment. Connections Connections are made as described belo w . Connector on the plasma monitor side: MONITORLINK CONTR OL/RS-232C connector .
36 Remedy • Def ault seting for ORBITER is ON (A UT O1). In this mode, picture mo ves intermittently around the screen. See page 26 to tur n off ORBITER. • If there are no abnormalities in the image and sound, the noise is caused by the cabinet reacting to changes in humidity .
37 *1 Overheat protector If the monitor becomes too hot, the overheat protector will be acti v ated and the monitor will be turned off. If this happens, turn of f the power to the monitor and unplug the power cord.
38 Specifications: PD-5030 Screen Size 43.5"(H) ⳯ 24.5"(V) inches 1106(H) ⳯ 622(V) mm diagonal 50" Aspect Ratio 16 : 9 Resolution 1365(H) ⳯ 768(V) pixels Pixel Pitch 0.032"(H) ⳯ 0.032"(V) inches 0.81(H) ⳯ 0.81(V) mm Color Reproduction 256 lev els, 16,770,000 colors Signals Synchronization Range Horizontal : 15.
39 Specifications: PD-6130 Screen Size 53.2"(H) ⳯ 29.9"(V) inches 1351(H) ⳯ 760(V) mm diagonal 61" Aspect Ratio 16 : 9 Resolution 1365(H) ⳯ 768(V) pixels Pixel Pitch 0.039"(H) ⳯ 0.039"(V) inches 0.99(H) ⳯ 0.99(V) mm Color Reproduction 256 lev els, 16,770,000 colors Signals Synchronization Range Horizontal : 15.
40 T able of Signals Suppor ted Screen mode Suppor ted resolution • When the screen mode is N ARR O W , each signal is con v erted to a 1024 dots ⳯ 768 lines signal. (Except for * 2, 3, 4 ) • When the screen mode is TR UE, the picture is displayed in the original resolution.
41 *1 Only when using a graphic accelerator board that is capable of displaying 852 ⳯ 480. *2 This signal is con verted to a 1024 dots ⳯ 640 lines signal. *3 The picture is displayed in the original resolution. *4 The aspect ratio is 5:4. This signal is con verted to a 960 dots ⳯ 768 lines signal.
42 Mitsubishi Plasma Display Panel Limited W arranty MITSUBISHI DIGIT AL ELECTRONICS AMERICA, INC . (“MDEA”) warrants to the original purchaser of this Plasma Displa y P anel that if purchased from an authorized MITSUBISHI A udio/Video Dealer , should it prov e def ective b y reason of improper workmanship and/or material: a.
Printed in USA 7S900055 Mitsubishi Digital Electronics America 9351 Jeronimo Road Irvine, CA 92618 DECLARATION OF CONFORMITY This device complies with Part 15 of FCC Rules.
Ein wichtiger Punkt beim Kauf des Geräts Mitsubishi Electronics PD-5030 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Mitsubishi Electronics PD-5030 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Mitsubishi Electronics PD-5030 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Mitsubishi Electronics PD-5030 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Mitsubishi Electronics PD-5030 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Mitsubishi Electronics PD-5030 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Mitsubishi Electronics PD-5030 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Mitsubishi Electronics PD-5030. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Mitsubishi Electronics PD-5030 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
