Benutzeranleitung / Produktwartung G 818 SCVI des Produzenten Miele
Zur Seite of 56
Operating instructions Incognito G 818 SCVi T o prevent accidents and machine damage, read these instructions before installation or use. UV M.-Nr . 05 620 631.
IMPORT ANT SAFETY INSTRUCTIONS CONSIGNES DE SÉCURITÉ IMPORT ANTES Caring for the en vironment Energy saving washing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Guide to the dishwasher W ash cabinet . .
Operation Adding detergent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Running the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 At the end of a program .
W ARNING – When using your dishwasher , f ollow basic precautions, including the follo wing: Read all instructions before installation or use of the dishwasher to prevent injury and machine damage. The manufacturer cannot be held responsible for damage or injury caused by improper use of this appliance.
This equipment is not designed for maritime use or for use in mobile installations such as recr eational vehicles or aircraft. However , under certain conditions it may be possible for an installation in these applications. Please contact the nearest Miele dealer or the Miele T echnical Service Department with specific requirements.
When loading tableware, place sharp items away from the door seal to prevent damage to the seal. Load knives pointing downwards to prevent injuries. Only use detergents and rinse aids recommended for r esidential dishwashers. Keep all detergents and rinse aids out of the reach of childr en.
A VER TISSEMENT – Lorsque v ous utilisez votre lave-v aisselle, veuillez prendre des précautions essentielles, y compris ce qui suit. Lisez attentivement l’ensemble des consignes av ant d’installer ou d’utiliser le lave-v aisselle afin de prévenir les blessures et éviter d’endommager l’appareil.
Installation L ’installation et les réparations devraient être ef fectuées uniquement par un technicien de service autorisé Miele. Les travaux effectués par des personnes non qualifiées peuvent s’avérer danger eux et annuler la garantie.
Utilisation N’utilisez le lave-vaisselle que lorsque tous les panneaux sont bien en place. Ne jouez pas avec les commandes. Afin de diminuer le risque de blessures, ne laissez pas les enfants jouer près de l’appareil ni monter dedans ou dessus. Évitez de malmener la porte ou les paniers du lave-vaisselle ou de vous y appuyer ou asseoir .
Energy sa ving washing This dishwasher is exceptionally economical in the use of water and electricity . For best results follow these tips: ^ For lowest energy consumption and the gentlest washing of china and crystal, connect the dishwasher to a cold water source.
W ash cabinet 1 Upper spray arm (not visible) 2 Cutlery tray 3 Upper basket 4 W ater feed for middle spray ar m 5 Middle spray arm 6 Lower spray arm 7 Rinse aid reservoir 8 Detergent dispenser 9 Data .
Control panel 15 On button / Indicator 16 Off button 17 Delay Start display 18 Delay Start button Note: Remove the protective film fr om the program list befor e the first use.
T o open the door ^ Pull the handle. If the door is opened during operation, the dishwasher will stop running. Once the door is closed the program will restart. Instructions on how to open the dishwasher if a door panel has not yet been installed can be found in the Installation Instructions.
W ater softener T o achieve good cleaning results, the dishwasher needs soft water . Hard water results in calcium deposits on dishware and in the dishwasher . If your tap water hardness is above 8 gr/gal (values are in US gallons) (140 ppm), the water should be softened.
Programming the water softener Y our water hardness level must be programmed into the dishwasher using the buttons on the control panel. The programming can be canceled and restarted at any time by turning the dishwasher off using the "Of f" button, (16).
15 - 70 gr/gal: ^ Press the f button. The f indicator will light. An indicator corresponding to a pr eset water hardness will light (see T able 2). T ab le 2: gr/gal ppm Button 15 - 16 270 - 280 a 17 .
Filling the salt reservoir If your water hardness level is gr eater than 8 gr/gal, the salt reservoir should be filled before the first use and when the "Salt" indicator lights. Only use water softener salt specially formulated for dishwashers.
Salt indicator When the salt reservoir is empty , the "Salt-PC" indicator will light, indicating that it should be refilled with reactivation salt. After the reservoir has been filled, the water softener is automatically reactivated the next time the dishwasher is started.
Rinse aid Rinse aid is recommended to pr event spotting on dishes and glassware. , Filling the rinse aid reservoir with detergent will damage the reservoir . Only pour rinse aid formulated fo r residential dishwashers into the reservoir . Adding rinse aid ^ Add rinse aid before the first use and whenever the "Rise aid" indicator lights.
Adjusting the dosage The dosage selector is preset to 3. This dispenses approximately 3 ml of rinse aid per program. It can be adjusted from 1 to 6. ^ Use a higher setting if spots appear on dry glassware. ^ Use a lower setting if streaking appears on dishes or glasses.
, Do not wash items soiled with ash, sand, wax, grease or paint in the dishwasher . Ash and sand do not dissolve and will be distributed throughout the inside of the dishwasher . W ax, grease and paint will cause permanent discoloration or damage to the dishwasher .
Items not recommended for dishwashing – Cutlery with wooden handles. – Wooden cutting boar ds. – Glued items such as old knives with handles glued together around the shank of the blade. – Hand made craft items, antique, metal trimmed or decorative glassware.
Cutlery tray (SC units) The removable cutlery tray makes unloading flatware easy . Simply carry the cutlery tray to where the flatware is stored and put the entir e basket away in one trip. For easier unloading cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Upper basket Adjusting the upper basket On select models, the upper basket can be raised or lowered to accommodate tall items. ^ Slide out the upper basket. ^ Pull up the levers at the sides of the upper basket and adjust the basket height. ^ Release the levers and the basket will lock in place.
Adjustable cup rac ks Raise the rack to make room for tall glasses. Lower it to double stack smaller pieces. Loading the dishwasher 25.
Lower basket The lower basket glassware insert is designed for washing tall glasses. T all glasses are held secur ely by the vertical suppor ts. The glassware insert can be removed to accommodate larger and heavier items such as plates, serving platters, sauce pans and bowls.
Additional inserts for the upper and lower baskets may be purchased from your Miele dealer or the Miele T echnical Service Department. T all Glassware Insert T o wash a large number of glasses, attaches to the lower basket. Upper Basket Glassware Insert T o wash long stemmed glassware, attaches to the upper basket.
Adding deter gent , Dishwasher detergents contain irritant and corrosive ingr edients. Keep children away fr om detergent. Do not fill the detergent dispenser until you are r eady to star t the dishwasher . Only use powder detergents or tablets formulated for residential dishwashers.
Running the dishwasher ^ Open the door . ^ Make sure the spray arms are not blocked. ^ T ur n on the dishwasher using the "On" button (15). ^ Select a wash program using the program selection buttons (22). The selected program indicator will light.
Interrupting a program A program is interrupted as soon as the door is opened. If the door is closed, the program will continue from wher e it was interrupted. , W ater in the dishwasher may be hot. There is a danger of being burned! Only open the door if absolutely necessary .
Program guide Program When to use Program cycle Pre- wash 12 Main wash Interim rinse 12 Final rinse Dry- ing Pots & Pans For heavily soiled pots and pans with dried on food Main wash temperature 1.
Additional features "T op Solo" ( 2 ) Using "T op Solo" will save water and energy . This program is r ecommended when there is only a small load to clean. "T op Solo" can be selected with all programs. With this feature, water is dir ected only to the top and middle spray arms.
Delay start ( d ) The start time of a program can be delayed from 1 to 9 hours. The delay start is set in one hour steps. When using delay start, make sure the detergent compartment is dr y before adding detergent. Wipe dry if necessary . ^ Press the "On" button (15).
T o start a program bef ore the delay start period has elapsed: ^ Open the door . ^ Press the "Of f" button (16). ^ Press the "On" button (15). ^ Select a program using the pr ogram selection buttons. ^ Select "T op Solo", if needed.
Extend drying If desired drying results ar e not consistently achieved, the heating element can be activated to heat at the end of a program. The "Extended drying" feature can also be activated to prevent condensation from collecting on the steam deflector .
With the aid of the following guide, minor problems can be fixed without a service call. , Repairs should only be carried out by a qualified and trained technician in accordance with local and national safety r egulations. Unauthorized repairs could cause personal injury or machine damage.
What if … P ossible fault Fix shortly after star ting a program, the dishwasher stops running and the optic indicator flashes? W ater intake error . The "Intake/Drain" indicator flashes. The water pressur e is less than 4.5 psi (0.3 bar). Contact a plumber .
What if … P ossible fault Fix after a program has ended, the optic indicator and the program indicator s flash? There may be a technical fault. – T ur n the dishwasher off. Despite the problem the dishwasher can be used. If the indicators flash again after the next program cycle, call Miele T echnical Service.
What if … P ossible fault Fix dishes are not clean? The dishes were not loaded correctly . See "Loading the dishwasher". The program was not powerful enough. Select a more intensive program, see the "Program guide". Not enough detergent was used.
What if … P ossible fault Fix tea or lipstick stains have not been completely remo ved? The wash temperature of the selected program was too low . Select a program with a higher temperature.
What if … P ossible fault Fix plastics are discolored? Natural dyes e.g. from vegetables may be the cause. Not enough detergent was used to break down natural dyes. Use more detergent, see "Adding detergent". Discoloration is permanent. there are rust stains on cutlery? The salt reservoir cap was not screwed on pr operly .
In the event of a fault which you cannot correct yourself please contact the Miele T echnical Service Department. U 1-800-999-1360 techserv@mieleusa.com V 1-800-565-6435 service@miele.ca When contacting the Miele T echnical Service Department, please quote the model and serial number of your appliance.
T o transport the dishwasher , e.g. when moving to a new home, note the following: – Empty the dishwasher . – Secure any loose parts, e.g. hoses, cables, cutlery baskets. – T ranspor t the dishwasher in the upright position. If unavoidable it may be transported on its back.
44.
User Maintenance Instr uctions T o prevent accidents and machine damage, read these instructions before installation or use..
T riple filter system The triple filter system in the base of the wash cabinet prevents food fr om being redeposited on dishes. It also pr otects the circulation pump fr om damage caused by foreign objects (e.g. br oken glass, bones). The filter system should be cleaned every 4 - 6 months or whenever a foreign object is trapped.
T o clean the underside of the filter , the flap must be opened: ^ Pull back the yellow clip. ^ Rinse all parts under running water . Scrub with a nylon brush if necessary . ^ Close the flap so that the clip engages. ^ Return the filter so it lies flat in the base of the wash cabinet.
Cleaning the spray arms Sometimes particles of food get stuck in the spray arm jets. The spray ar ms should be inspected and cleaned every 4 - 6 months. ^ T ur n off the dishwasher befor e cleaning. Remove the spray arms as follows: ^ Remove the cutlery tray (if present).
Cleaning the wash cabinet Generally , the wash cabinet is self cleaning if the correct amount of dishwasher detergent is used. The wash cabinet can be cleaned with a dishwasher cleaner such as Dis Cleaner available from your Miele dealer or the Miele T echnical Service Department.
Cleaning the control panel ^ Only clean the contr ol panel with a damp cloth. , Do not use too much water when cleaning the controls. W ater could penetrate into the electronics and cause damage. , Do not use abrasive, glass or all purpose cleaners. They will damage the surface.
Cleaning the water inlet filter A filter is incorporated in the intake hose attached to the dishwasher’ s shut off valve. If your water is har d, or the pipes contain sediment, this filter may clog and prevent enough water fr om entering the wash cabinet.
Cleaning the drain pump and non-return valve If the dishwasher is not completely drained at the end of a program, the drain pump or non-return valve may be blocked. ^ T ur n off the dishwasher . ^ Remove the triple filter (see "Cleaning the filter in the wash cabinet").
53.
54.
55.
M.-Nr . 05 620 631 / 01 Alterations rights reserved / G 818 Plus 2505.
Ein wichtiger Punkt beim Kauf des Geräts Miele G 818 SCVI (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miele G 818 SCVI noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miele G 818 SCVI - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miele G 818 SCVI reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miele G 818 SCVI erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miele G 818 SCVI besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miele G 818 SCVI verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miele G 818 SCVI. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miele G 818 SCVI gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
