Benutzeranleitung / Produktwartung B990 des Produzenten Miele
Zur Seite of 36
Operating instructions Rotary Iron B 990 To prevent accidents and machine damage, read these instructions before Installation or use. M.-Nr. 07 658 660 en - US, CA.
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Guide to the Rotary Iron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Moving the appliance . . . . . . . . .
Read the operating instructions carefully before using this appliance for the first time. They contain important information about the safety, use and maintenance of the appliance. Please read this booklet carefully to prevent accidents and machine damage.
~ Before connecting the appliance, ensure that the connection data on the data plate (fusing, voltage and frequency) match the household electrical supply. If in doubt, consult an electrician. ~ Do not use an extension cord to connect this appliance to electricity.
~ The swing out bar is only to be used to hang laundry. Swing it back immediately after use. Take care not to press down on the bar when it is swung out. This could tip over the rotary iron. ~ Turn the appliance off before removing the plug from the electrical outlet.
a Temperature selector b Emergency release c Control panel d Release catch e Power cord f Foot pedal g Ironing table h Bar for hanging ironed laundry i Feed board j Roller (with ironing cover) k Heate.
Control panel a Roller speed selector b On-Off indicator " 0-I " c On-Off button " 0-I " for turning the rotary iron on and off d Temperature indicator o C Guide to the Rotary Iron.
Transport strut ^ Pull the transport strut out (see illustration). Keep the transport strut in a safe place. It must be re-fitted if the appliance has to be moved again (e.g. when moving to a new home). If the transport strut is in place, only transport the rotary iron in a folded position.
^ Hold the ironing table and release the catch, located on the right hand side at the back, underneath the ironing table. ^ Swing the top section of the rotary iron to the side until it clicks horizontally into position.
Power cord The power cord is wound around a hook underneath the ironing table. ^ Unwind the cord. , Do not insert the plug into the electrical socket yet. * The plug shown is for illustration only. Dust cover The dust cover which protects the roller during transportation must be removed.
^ Adhere the sticker (included) to the temperature control, as shown above. Before using for the first time 11.
Preparing the work area A height adjustable chair and a flat surface, like a table to lay ironed laundry on, are useful. When positioning the rotary iron horizontally be sure to secure the appliance so that it does not roll.
Preparing the laundry Correct preparation of the laundry is essential for easy ironing. Before ironing, the laundry should be: – dampened – pulled into shape and smoothed out – sorted.
Testing the finger guard The finger guard is a safety feature and should be checked each time the rotary iron is used. ^ With the rotary iron turned on, press the foot pedal down. The heater plate comes down onto the rotating roller. ^ If you lift the finger guard now, the roller stops rotating and the heater plate rises.
Turning on and off The rotary iron is turned on and off with the " 0-I " button. To turn on ^ Press the button in. The indicator light comes on. To turn off ^ Press and release the button. The indicator light goes out. Selecting the ironing temperature The temperature selector is used to set the ironing temperature.
^ Turn the temperature selector to the desired temperature. The temperature "C°" indicator will light while the heater plate is heating up. The light will go out when the temperature selected is reached. When ironing a fabric blend, e.g. poly cottons, the more delicate fiber determines the ironing temperature.
Ironing The ironing process is controlled by the foot pedal which has three operating positions: – raising the heater plate (rest) – pressing – ironing To iron ^ Press the foot pedal down to the floor. , Do not put fingers between the heater plate and the roller.
Positioning the laundry ^ Arrange the laundry items on the feed board so that they are straight and then smooth out. ^ Then turn the roller by hand , always keeping your hands away from the heater plate , so that the edge of the item to be ironed can be held by the heater plate.
Ironing tips – To avoid creasing stop the roller, pull the item back slightly and smooth out. If necessary, dampen again with a wet cloth or spray bottle. – If possible, always use the whole length of the roller, otherwise the roller will lose its elasticity.
Power failure In the event of a power failure, pull the emergency release lever up. If there is a power failure when the rotary iron is in use, the heater plate will stay on the roller. The item being ironed will be held there possibly becoming scorched.
Tablecloths ^ Avoid folds by ironing the middle first. ^ Place the tablecloth crossways so that the ends hang over to the left and right. ^ Iron the middle section. ^ Fold in half with unironed edges together and place over the left end of the roller with the ironed middle section hanging over the edge to prevent creasing.
Duvet covers If the duvet cover has buttons at the open end, iron the buttons first. Note: Only pass this end through the rotary iron if the buttons are heat-resistant. ^ Start the first run by carefully feeding this end in first on the left side of the roller, taking care not to damage any buttons.
Shirts ^ Remove the feed board to iron shirts. 1. Shoulder yoke ^ Arrange the yoke, collar first, on the roller and smooth out. ^ Hot press the yoke. 2. Collar The collar is ironed on both sides using the left hand end of the roller. Stop ironing when the button comes to the heater plate.
4. Back ^ Start at the side seam. Pull the shirt over the roller as far as the arm hole. Smooth it out. ^ Starting from the side seam iron past the armhole, then pull the shirt further onto the roller and iron the full back length to the second arm hole.
Pants Ironing pants and jeans ^ Iron the upper part from waistband to inseam of pants and jeans in sections. Set on a slow speed. ^ Iron the legs from hem to inseam one leg after another. Pressing woolen and dress pants ^ Lay the pant legs separately on the roller.
Turn the iron off and unplug it from the outlet before performing any maintenance work. Cleaning the heater plate ^ Check that the temperature selector is set g . ^ Allow the heater plate to cool before cleaning. ^ Pull the emergency release lever up to make sure easier cleaning.
, The ironing cover should only be changed when the appliance is cold. ^ Remove the feed board. ^ Untie the old ironing cover cords at each end of the roller. ^ Unwind the old ironing cover. When the iron is turned on, the heater plate heats up immediately.
^ Insert the long edge of the new ironing cover into the retaining slot with the side seams inside (upside down). Keep side ties hanging free and smooth out. ^ Turn the roller by hand in the direction you iron (see arrow) until the retaining slot is at the bottom.
^ Tighten the cords at the left and right hand sides of the roller, tie together and tuck in. ^ Put the feed board back in place. ^ Turn the rotary iron on - the heater plate will rise.
Repairs should only be carried out by an authorized technician in accordance with local and national safety regulations. Unauthorized repairs could cause injury or appliance damage. The rotary iron does not turn on. Possible fault Solution The rotary iron has no power.
In the event of a problem, please contact the Miele Technical Service Department. When contacting the Technical Service Department, please quote the Model and Serial number of your appliance, both are shown on the data plate, located underneath the front side of the ironing table.
The appliance is supplied with a power cord and NEMA 5-15 P plug ready for connection to an a.c. single phase 120 V 60 Hz supply (see data plate). The fuse rating is 15 amps. , Do not modify the machine power cord or plug, the machine is approved for USA and CDN.
Height 37 3 / 4 " (folded 41 3 / 8 ") [95.9 (folded 105.2) cm] Width 38 3 / 4 " (folded 19 5 / 8 ") [98.5 (folded 50) cm] Depth 15" [38 cm] Weight 84 Ibs [38 kg] Voltage see d.
Disposal of packing materials The cardboard box and packing materials are biodegradable and recyclable. Please recycle. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of children. Danger of suffocation! Disposal of an old appliance Old appliances contain materials that can be recycled.
35.
M.-Nr. 07 658 660 / 01 Alteration rights reserved / 0410 INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
Ein wichtiger Punkt beim Kauf des Geräts Miele B990 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miele B990 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miele B990 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miele B990 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miele B990 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miele B990 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miele B990 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miele B990. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miele B990 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
