Benutzeranleitung / Produktwartung 07 502 390 des Produzenten Miele
Zur Seite of 84
Operating instructions for dishwashers To avoid the risk of accidents or damage to the appliance, it is essential to read these instructions as well as the installation plan before it is installed and used for the first time.
Guide to the appliance .............................................5 Appliance overview .................................................5 Control panel ......................................................6 Display .................................
Lower basket .....................................................3 0 Vario inserts ...................................................3 0 Bottle holder ...................................................3 1 Cutlery ...................................
After sales service ................................................5 9 Repairs .......................................................5 9 Future updates .................................................5 9 For testing institutes .....................
Appliance overview a Upper spray arm (not visible) b Cutlery tray (depending on model) c Upper basket d Middle spray arm e Air inlet for drying (depending on model) f Lower spray arm g Filter combinat.
Control panel a Selector sensors For selecting the option displayed next to them. For altering the values displayed (+/-). For navigating to further screens. The selector sensors light up when active. b On/Off sensor K For switching the appliance on and off.
Display The display is used to select the following: – the programme – extras – the delay start time – the Settings menu ! – information During a programme, the display shows the following: .
Miele | home enabled appliances send information via the household wiring network to the master appliance d / e about the operational status of the appliances, as well as information about the progress of the programme.
This appliance conforms to current safety requirements. Inappropriate use can, however, lead to personal injury and damage to property. To avoid the risk of accidents and damage to the appliance, please read these instructions carefully before using it for the first time.
Technical safety ~ Before setting up the appliance, check it for any externally visible damage. Under no circumstances should you use a damaged appliance. A damaged appliance could be dangerous. ~ The dishwasher must only be plugged into the electricity supply via a suitable switched socket.
~ This appliance may only be installed in mobile installations such as ships if a risk assessment of the installation has been carried out by a suitably qualified engineer. ~ The plastic housing of the water connection contains an electrical component.
Installation ~ The dishwasher must be installed and connected in compliance with the installation diagram supplied. ~ The dishwasher must be correctly aligned to ensure problem-free operation.
~ Inadvertently filling the salt reservoir with powder or liquid dishwasher detergent will damage the water softener. Make sure you have picked up the correct packet of dishwasher salt before filling .
Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled. Ensure that any plastic wrappings, bags, etc. are disposed of safely and kept out of the reach of babies and young children.
Energy saving washing This dishwasher is exceptionally economical in its use of water and electricity. You can make the most of your appliance by following these tips: ^ For most economical dishwashing make full use of the baskets without overloading the dishwasher.
To open the door At the end of programmes with a drying phase (see "Programme chart") the door will open automatically a little in order to help the drying process. This function can be deactivated (see "Settings menu, Drying plus").
Welcome screen ^ Switch the dishwasher on using the K sensor. If the dishwasher is being switched on for the first time, the welcome screen will appear. Setting the language The display will then change automatically to the screen for setting the language.
Setting the time of day The display will then change to the screen for setting the time. Time [ [ [ + $ 10 :21 - # OK ! ^ Set the hours with the +/- sensors and confirm with OK. Then set the minutes, and confirm with OK. Display The display will then change to the screen for setting the display for the time of day.
Miele branded products are available from the Miele Spare Parts Department or via the internet at www.miele-shop.com. Before using the appliance for the first time, you require: – Approx. 1 kg dishwasher salt, – Domestic dishwasher detergent, – Rinse aid formulated for domestic dishwashers.
You can check the water hardness level measured by the water softener sensor in the display (see Settings menu ! , Water hardness). If the water in your area is very soft and constantly lower than 0.7 mmol/l (4 °d) you do not need to add salt. The "Insufficient salt" message will be deactivated automatically.
Do not fill the salt reservoir with water. ^ Add salt only until the reservoir is full or until water runs out of the opening. The salt reservoir holds approx. 1 kg of salt, depending on the brand used. Do not add any more than 1 kg of salt. As the salt reservoir is filled, displaced water may overflow.
Rinse aid Rinse aid is necessary to ensure water does not cling and leave marks on crockery during the drying phase and helps crockery dry faster after it has been washed. Rinse aid is poured into the storage reservoir and the amount set is dispensed automatically.
^ Add rinse aid only until it is visible in the opening. The rinse aid reservoir holds approx. 110 ml. ^ Close the flap firmly so that it clicks into place. Otherwise water can enter the rinse aid reservoir during a programme. ^ Wipe up any spilled rinse aid.
Note Remove coarse food residues from crockery. There is no need to rinse items under running water. , Do not wash items soiled with ash, sand, wax, lubricating grease or paint in the dishwasher.
Items not suitable for dishwashers: – Wooden cutlery and crockery or items with wooden parts: these may discolour and fade. The glue used in these items is not dishwasher-proof and wooden handles may come loose after being washed in a dishwasher.
Upper basket , For safety reasons, do not operate the dishwasher without the upper and lower baskets in place (except when running the Tall items 65°C programme). ^ Use the upper basket for small, lightweight and delicate items such as cups, saucers, glasses, dessert bowls, etc.
Hinged cup rack ^ To make room for tall items, raise the rack upwards. G 2XXX models: You can set the cup rack at two different heights. ^ Pull the cup rack upwards and click it back into position at the required height.
Support rail This support is designed to hold tall glasses and glasses with stems securely. ^ Lower the support and lean tall glasses against it. ^ You can also remove a section of the cutlery tray to make more room for tall glasses.
Adjusting the upper basket In order to gain more space for taller pieces of crockery in the bottom or upper basket, the upper basket can be adjusted on three levels with 2 cm between each level. The upper basket can also be set at an angle with one side high and the other side low.
Lower basket ^ For larger and heavier items such as plates, serving platters, saucepans, bowls, etc. Small items such as saucers can also be placed in the lower basket. Do not place delicate glassware in the lower basket. Vario inserts The vario inserts are used for washing cups, glasses, plates, saucers, pots and pans.
Narrow vario insert You can remove the narrow vario insert to make more room for larger items of crockery, e.g. a large, flat pot, or another type of insert: To remove it: ^ Press the insert downwards a and press the catch inwards at the same time b .
Cutlery Cutlery tray (depending on model) ^ Arrange the cutlery in the tray as shown. To make unloading much easier, cutlery should be grouped in zones, one for knives, one for forks, one for spoons, etc.
Cutlery basket (depending on model) ^ To avoid the risk of injury, knives and forks should be placed with the handles upwards in the basket. However, cutlery placed handle down in the basket will come out cleaner and drier. ^ Place small spoons in the individual slots to either side of the cutlery basket.
Detergent , Only use detergents formulated for domestic dishwashers. Do not use washing-up liquid. Miele branded dishwasher cleaning products are available from the Miele Spare Parts Department or via the internet at www.
, Avoid inhalation of powder detergents and do not ingest dishwasher detergent. Dishwasher detergents contain irritant or corrosive ingredients which can cause burning in the nose, mouth and throat if swallowed, or inhibit breathing. Consult a doctor immedi - ately if detergent has been swallowed or inhaled.
Switching on ^ Make sure the spray arms are not obstructed. ^ Close the door. ^ Open the stopcock, if it is closed. ^ Switch the dishwasher on using the K sensor. The main menu will appear in the display. If the memory function is activated, the programme menu for the programme last selected will be displayed instead (see Settings menu ! , Memory).
To select a different programme, touch the Clear sensor U to return to the main menu. Selecting Extra options You can now select Extra options for your chosen programme. ^ To do this, first select the Extras option in the menu. The Extras available for your programme will appear in the display.
Starting a programme ^ Select the Start option. The programme starts, and the prompt Add an item shows in the display. As long as this prompt is showing, crockery can be added without compromising the wash results. A programme can only be cancelled in the first few minutes.
At the end of a programme If the message Programme finished or Drying plus comes up in the display, and the door has opened slightly, this indicates that the programme has finished.
Changing a programme Important: If the detergent dispenser flap has already opened, do not change the programme. If a programme has already started and you wish to change it, proceed as follows: Sensor wash 12:21 [ 8 Add an item Time left 1:10 h Cancel ! ^ Select Cancel .
Delay start The start time of a programme can be delayed, e.g. to benefit from economy rates of electricity. A delay start time of between 15 minutes and 24 hours can be selected. The delay start time is set in 15 minute steps. When using the Delay start function, make sure that the detergent compartment is dry before adding detergent.
^ Confirm the start time with OK . ^ Select the Start option. Sensor wash 12:00 [ R Start at 20:00 Cancel ! The programme name and the start time will appear in the display. When the set time is reached, the programme selected will begin automatically.
Check your dishwasher regularly (approx. ever y4-6 months). This way faults and problems can be avoided. Miele branded cleaning and conditioning products are available from the Miele Spare Parts Department or via the Internet at www.miele-shop.com. , The external surfaces of the dishwasher are susceptible to scratching.
Checking the filters in the wash cabinet The filter combination in the base of the wash cabinet retains coarse soil from the suds solution, preventing it accessing the circulation system and re-entering the cabinet through the spray arms. , This dishwasher must not be used without all the filters in place.
To clean the inside of the filter, the flap must be opened: ^ Press catches a together in the direction of the arrows as shown, and open the filter b . ^ Rinse all the filters under running water. ^ Then close the flap so that the catch engages. ^ Replace the filter combination so that it lies flat in the base of the wash cabinet.
Cleaning the spray arms Particles of food can get stuck in the spray arm jets and bearings. The spray arms should therefore be inspected and cleaned regularly (approx. every 4 - 6 months). ^ Switch the dishwasher off. Remove the spray arms as follows: ^ Take out the cutlery tray (if your dishwasher is fitted with one).
With the aid of the following guide, faults in the performance of the appliance, some of which may result from incorrect operation can be put right without contacting the Service Department. The following guide may help you to find the reason for a fault, and to correct it.
Problem Possible cause Remedy The buzzer sounds. The following fault message appears in the display: Before rectifying the problem: – Switch the dishwasher off using the On/Off sensor K . Technical fault FXX Call Service There may be a technical fault.
The dishwasher does not fill/drain. Problem Possible cause Remedy The buzzer sounds. The following fault message appears in the display: Water inlet fault Please open the stopcock. The stopcock is closed. Open the stopcock fully. Water inlet fault FXX Before rectifying the problem, you must: – Switch the dishwasher off using the On/Off sensor K .
Problem Possible cause Remedy In the display for the Without heater programme, the following fault message appears: Water intake temp. too low The intake water has not reached the required temperature of 45 °C (see Connection to the water supply). – Start the programme again.
General problems Problem Possible cause Remedy The display is dark. The display has switched off automatically to save energy (Standby mode). Touch any sensor.
Problem Possible cause Remedy Detergent residue is left in the dispenser at the end of a programme. The dispenser was still damp when detergent was added. Make sure the dispenser is dry before adding detergent. The detergent dispenser lid cannot be closed properly.
Noises Problem Possible cause Remedy Knocking noise in the wash cabinet. A spray arm is knocking against an item in a basket. Interrupt the programme, and rearrange the items which are obstructing the spray arm. Rattling noise in the wash cabinet. Items of crockery are insecure in the wash cabinet.
Unsatisfactory washing result Problem Possible cause Remedy The dishes are not clean. The dishes were not loaded correctly. See notes in "Loading the dishwasher" The programme was not powerful enough. Select a more intensive programme. See Programme chart.
Problem Possible cause Remedy Dishes, cutlery and glasses are not dry or are flecked. The amount of rinse aid may be insufficient, or the rinse aid reservoir empty. Replenish the reservoir, increase the dosage or change the brand of rinse aid. See "Before using for the first time".
Problem Possible cause Remedy Glassware has a brown or blue tinge, and film cannot be wiped off. This may be caused by the detergent. Change your detergent. Glassware is dull and discoloured; film cannot be wiped off. The glassware is not dishwasher-proof.
Cleaning the water inlet filter A filter is incorporated in the screw connection of the valve on the water inlet hose. The filter must be cleaned when dirty, otherwise insufficient water flows into the wash cabinet. , The plastic housing of the water connection contains an electrical component.
Cleaning the drain pump and non-return valve If the water has not been pumped away at the end of a programme the drain pump or the non-return valve might be blocked. They are, however, easy to clean. ^ Disconnect the dishwasher from the mains supply. Switch off at the mains socket and withdraw the plug.
Repairs In the event of any faults that you cannot remedy yourself, please contact: – Your Miele dealer, or – the Miele Service Department (see back cover for address). Please note that telephone calls may be monitored and recorded to improve our service.
Crockery Food deposits Action required Mixed, everyday crockery All normal food deposits This needs an adaptable programme... Shorter duration... Heat-sensitive glasses and plastic Fresh, easily removed food deposits This needs a short programme... Mixed crockery This needs a gentle programme with glass care.
Programme Detergent Compartment I 2) Compartment II 2) Sensor wash – 25 ml or 1 tab + Turbo option Quick wash 40°C – 20 ml or 1 tab 3) Sensor wash gentle – 20 ml or 1 tab Light soiling 50°C .
Programme Programme sequence Pre-wash Main wash °C Interim rinse Final rinse °C Drying 12 Sensor wash Variable programme sequence, sensor controlled adjustment according to the amount of crockery an.
Consumption 1) Duration 1) Energy Water Cold water connection (15 °C) kWh Hot water connection (55 °C) kWh Litres Cold water connection (15 °C) h:min Hot water connection (55 °C) h:min 0.95-1.35 0.70-1.00 8-17 1:30-2:38 1:18-2:21 0.55 0.20 10 0:38 0:27 0.
Programme When to use Hygiene Programme with special parameters for hygienic removal of bacteria from baby bottles, chopping boards, utensils etc. Pre-wash For rinsing crockery to avoid smells, if a complete cycle is not yet needed.
Programme sequence Consumption 1) Duration 1) Energy Water Pre- rinse Main wash °C Interim rinse 12 Final rinse °C Drying Cold water connec - tion (15 °C) kWh Hot water connec tion (55 °C) kWh Litres Cold water connec - tion (15 °C) h:min Hot water connec - tion (55 °C) h:min 70 X 70 X 1.
To make the most of your dishwasher Optional accessories for particular purposes are available from your Miele dealer, the Spare Parts Department or online at www.
Electrical connection U.K. , All electrical work must be carried out by a suitably qualified and competent person, in accordance with current local and national safety regulations (BS 7671 in the UK). Ensure power is not supplied to the appliance until after installation work has been carried out.
The Miele waterproof anti-leak system Providing your dishwasher has been installed correctly, the Miele waterproof anti-leak system will protect you from water damage throughout its lifetime. Connection to the water supply , Water in the dishwasher must not be used as drinking water.
Drainage – The appliance drainage system is fitted with a non-return valve, which prevents dirty water from flowing back into the dishwasher via the drain hose. – The dishwasher is supplied with approx. 1.5 m of flexible drain hose with an internal diameter of 22 mm.
Dishwasher model G 1XXX G 2XXX Height freestanding 84.5 cm (adjustable +3.5 cm) - Height built-in 80.5 cm (adjustable + 6.5 cm) 84.5 cm (adjustable + 6.5 cm) Height of building-in recess Min. 80.5 cm (+ 6.5 cm) Min. 84.5 cm (+ 6.5 cm) Width 59.8 cm 59.
Settings menu ! for changing standard settings To open the Settings ! menu ^ Switch the dishwasher on with the On sensor K if it is switched off. The main menu will appear in the display. If the memory function is activated, the programme menu for the programme last selected will be displayed instead (see "Memory").
Language ! The display can be set to appear in one of several different languages. You can change the language for the display via the Language ! sub-menu. ^ Select the language you want and confirm this with OK . The flag after the word Language acts as a guide if a language which you do not understand has already been set.
Detergent type For optimum results you can programme your dishwasher via the Detergent type menu for the type of detergent you are using. The options available are: normal dishwasher detergent, 2 in 1 tabs or Combination tabs. The programme sequence and duration will be adjusted for the type of detergent selected.
Drying plus At the end of programms with a drying phase, the door will open automatically a little in order to help the drying process. This function can be deactivated if wished.
External water softener If your dishwasher is connected to an external water softening system which uses salt to reactivate, to achieve good cleaning results you will still need to set the water hardness level of the water softening unit on the dishwasher to the water hardness level of the water supplied from the external water softening system.
Change main menu You can change the order of the programmes in the programme selection menu and also enter your favourite programmes into the first three programme places.
Save extras You can set additional functions, e.g. Pre-wash, for individual programmes (see "Operation, Selecting Extra options"). You can use the Save extras option to save settings you have chosen for a particular programme so that they are automatically selected when you run the programme in the future.
System lock The system lock prevents your dishwasher being used without your knowledge. If an attempt is made to switch the dishwasher on when the system lock is activated Appliance locked will appear in the display. The lock must be cancelled before the dishwasher can be used.
Temperature The temperature can be displayed in °C/Celsius or °F/Fahrenheit. The factory default setting is °C. ^ Select the option you want and confirm with OK .
Night time You can select the times for night time to begin and end. ^ Select the Start at option in the menu. ^ Set the start time for the night using the +/- sensors, and confirm with OK . Set the end time for the night using the +/- and confirm with OK .
Showroom programme The programme is for display use only. The dishwasher is fitted with various demonstration programmes for showroom use. The Demo mode and Demo mode in continuous loop programmes demonstrate the operation and functions of the dishwasher: – Demo mode : This programme is started by pressing a sensor.
82.
83.
Alteration rights reserved/ G1833/G2833 / 2709 M.-Nr. 07 502 390 / 01.
Ein wichtiger Punkt beim Kauf des Geräts Miele 07 502 390 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Miele 07 502 390 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Miele 07 502 390 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Miele 07 502 390 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Miele 07 502 390 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Miele 07 502 390 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Miele 07 502 390 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Miele 07 502 390. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Miele 07 502 390 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
