Benutzeranleitung / Produktwartung 7200 des Produzenten Meyer
Zur Seite of 60
MANUFACTURED BY County Hwy. A West P.O. Box 405 Dorchester, Wisconsin 54425-0405 Phone 715-654-5132 • FAX 715-654-5513 1-800-325-9103 www.meyermfg.com E-mail: sales@meyermfg.
Model 7200 -2- TABLE OF CONTENTS MANUFACTURER’S WARRANTY .......................................3 INTRODUCTION ................................................4 SAFETY PRECAUTIONS ............................................5 SAFETY FIRST ..........
Model 7200 -3- NEW MEYER INDUSTRIAL SPREADER MANUFACTURER’S WARRANTY I. The “Product Registration & Inspection Certificate” along with the original billing invoice “Owners Registration Form” must be completed in full and promptly returned to Meyer Mfg.
INTRODUCTION Congratulations on your purchase of a new Meyer farm equipment product. Undoubtedly you have given much consideration to your purchase and we’re proud that you have selected Meyer. Pride in craftsmanship, engineer - ing and customer service have made Meyer products the finest in the farm equipment industry today.
Model 7200 -5- SAFETY PRECAUTIONS This symbol is used to call attention to instructions concerning personal safety. Be sure to observe and follow these instructions. Take time to be careful! WARNING: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY THE FOLLOWING SAFETY INFORMATION.
SAFETY FIRST A brief definition of signal words that may be used in this manual is as follows: DANGER Indicates an imminently hazardous sit - uation which, if not avoided, WILL result in serious injury or death.
SAFETY FIRST The Meyer Super Spreader is manufactured with operator safety in mind. Located on the manure spreader are vari - ous decals to aid in operation and warn of danger or caution areas. Pay close attention to all decals on the spreader. DO NOT REMOVE ANY DECALS.
PRE-OPERATION WARNING: BEFORE OPERATING, READ THIS OWNERS MANUAL COMPLETELY. PAY PARTICULAR ATTENTION TO THE “SAFETY PRECAUTION” AND “SAFETY FIRST” PAGES. READ ALL SAFETY MESSAGES HIGHLIGHTED BY “SAFETY ALERT SYMBOLS” THROUGHOUT THE MANUAL.
WARNING: HYDRAULIC FLUID ESCAPING UNDER PRESSURE CAN HAVE SUFFICIENT FORCE TO PENETRATE SKIN. KEEP ALL HOSES AND CONNECTIONS IN GOOD SERVICEABLE CON - DITION.
WARNING : INSTALL A SMV EMBLEM ON REAR OF SPREADER FOR TRANSPORTING ON ROADWAYS AND KEEP THIS EMBLEM CLEAN AND BRIGHT. FAILURE TO HEED MAY RESULT IN SERI - OUS PERSONAL INJURY OR DEATH. If you will travel on public roads and it is legal to do so, you must know all rules governing such operation.
WARNING : DO NOT CLEAN, ADJUST OR LUBRICATE WHILE SPREADER IS IN MOTION. FAILURE TO HEED MAY RESULT IN SERIOUS PER - SONAL INJURY OR DEATH. Scrape clean any remaining manure from inside the rear of spreader. Clean all manure from ends of augers, flow control rear gate and spinners.
OPERATION LOADING CAUTION : TO PREVENT DAMAGE TO AU - GERS, SPINNERS, AND DRIVE LINES, FOREIGN OBJECTS (STONES, CONCRETE, TIMBER, METAL OR LARGE FROZEN CHUNKS OF MANURE) SHOULD NEVER BE LOADED INTO THE SPREADER. DANGER : NEVER ENTER THE SPREADER BOX FOR ANY REASON WITHOUT FIRST DISCON - NECTING PTO SHAFT FROM TRACTOR.
The rear spinners have been designed and tested to provide the best spread pattern for most liquids and semi solid manure. However, the pattern will vary for each specific condition. The factors that contribute most to differing patterns will be moisture content and the amount and length of bedding material.
STORAGE AFTER USE WARNING : DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES BEFORE CLEANING, ADJUSTING, OR SERVICING THIS MA - CHINE. FAILURE TO HEED MAY RESULT IN SERI- OUS PERSONAL INJURY OR DEATH. Before storing this spreader for an extended period of time perform the following: Allow the spreader to completely clean out the last load.
PTO DRIVELINE WARNING: BEFORE ATTEMPTING TO OPERATE THIS SPREADER, READ AND STUDY ALL SAFETY INFORMATION. IN ADDITION, MAKE SURE THAT EVERY INDIVIDUAL WHO OPERATES OR WORKS WITH THE SPREADER, WHETHER FAMILY MEMBER OR EMPLOYEE, IS FAMILIAR WITH THESE SAFETY PRECAUTIONS.
Adjust the drawbar at 16-20” above the ground. Extend or shorten the drawbar so horizontal distance from end of tractor PTO shaft to center of hitch pin hole is 16” for 1000 RPM 1-3/8-21 spline, (14” for 540 RPM 1-3/8-6 spline) (20” for 1000 RPM 1-3/4-20 spline).
ADJUSTMENTS WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. FRONT DRIVE ROLLER CHAINS There are six roller chain drives located at the front of the spreader.
Model 7200 -18- FIGURE 9 . THIRD CHAIN DRIVE TENSIONER ARM ROLLER CHAIN IDLER NYLON ROLLER FIGURE 10. RH AUGER CHAIN DRIVE SPRING LOADED ADJUSTER IDLER NYLON ROLLER ROLLER CHAIN RH AUGER SPROCKET FIGURE 11.
SPINNER MATERIAL GUIDES Regularly inspect and adjust two spinner material guides located at both the left rear and right rear of the spreader. Create a 1/4-1/2” clearance between material guides and spinner teeth, figure 13. Maintain the recom - mended clearances for maximum spreading pattern.
LUBRICATION WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH. DAILY LUBRICATION (every 8-12 loads ) Grease (2) rear spinner lower bearings.
MONTHLY LUBRICATION Maintain oil level in the corner gearbox at the centerline of the input shafts. Check regularly for any observable oil leakage. If oil leakage is excessive, replace required input/output shaft oil seals.
Model 7200 -22- REPAIR PARTS 918-0208 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-21 SPLINE / 1-3/8” YOKE WWE2480 (80 DEGREE C.V.).
Model 7200 -23- KEY MEYER PART NO. DESCRIPTION 1 918-0208-1-1 Yoke 1-3/8"-21 Splined As - sembly 2 918-0208-1-2 Grease Zerk in item 3 3 918-0208-1-3 Double Yoke 4 918-0208-1-4 Inboard Yoke 5 918-.
Model 7200 -24- 918-0210 PTO DRIVE SHAFT ASSEMBLY 1000 RPM-20 SPLINE / 1-3/4” YOKE WWE2480 (80 DEGREE C.V.).
Model 7200 -25- KEY PART NO. DESCRIPTION 1 918-0210-1-1 Yoke 1-3/4"-20 Splined Assembly 2 918-0208-1-2 Grease Zerk in item 3 3 918-0208-1-3 Double Yoke 4 918-0208-1-4 Inboard Yoke 5 918-0208-1-5 .
Model 7200 -26- AUGER DRIVE THIRD REDUCTION KEY PART NO. DESCRIPTION 1 925-3703 Front Bearing Plate Assy. 2 914-3808 2-1/4" Bearing 4-Bolt 3 910-0080 Sprocket Weldment 2-1/2" Shaft, #80/120 .
Model 7200 -27- This Page Intentionally Blank.
Model 7200 -28- FRONT SHIELD & SIDE SHAFT DRIVE.
Model 7200 -29- KEY PART NO. DESCRIPTION 1 925-3703 Front Bearing Plate As - sembly 1A 32-0018-1 Heavy Duty Latch 1B 32-0018-2 Keeper Latch 2 925-3706 Right Hand Front Support 3 924-3701 Right Front S.
Model 7200 -30- AUGER DRIVE FIRST REDUCTION UNITS WITH SHEAR SPROCKET ASSEMBLY. SEE FOLLOWING PAGE FOR SN’S..
Model 7200 -31- KEY P ART NO. DESCRIPTION 1 14-0031 2" Bearing 4-Bolt 2 851-2520-2Z 1/4-20 x 2" Grade 5 Shear Bolt 3 910-0058 2" Shear Sprocket Weldment 4 815-2520-Z 1/4-20 Nylon Insert Locknut 5 910-0054 Shear Sprocket Assembly (1000 RPM) 910-0066 Shear Sprocket Assembly (540 RPM) 5A 913-3602-2 2" I.
Model 7200 -32- AUGER DRIVE SECOND REDUCTION UNITS WITH SHEAR SPROCKET ASSEMBLY. SEE FOLLOWING PAGE FOR SN’S..
Model 7200 -33- KEY PART NO. DESCRIPTION 1 14-0031 2" Bearing 4-Bolt 2 851-2520-2Z 1/4-20 x 2" Grade 5 Shear Bolt 3 910-0058 2" Shear Sprocket Weldment 4 815-2520-Z 1/4-20 Nylon Insert Locknut 5 910-0054 Shear Sprocket Assembly (1000 RPM) 910-0066 Shear Sprocket Assembly (540 RPM) 5A 913-3602-2 2" I.
Model 7200 -34- RH AUGER DRIVE FINAL REDUCTION.
Model 7200 -35- KEY PART NO. DESCRIPTION 1 933-3701 3" Retaining Ring 2 910-0081 2-1/2" Auger Drive Sprocket Weldment 3 910-0071-1 140B35 3" 23 Spline Auger Sprocket (Prior to Serial # SI067200201) 910-0100 140B35 Shear Sprocket Assembly (Serial #SI067200201 & Later) 3A 831-5020-1.
Model 7200 -36- LH AUGER DRIVE FINAL REDUCTION KEY PART NO. DESCRIPTION 1 925-3766 Right/Left Auger Bushing Holder Assembly 2 913-3701 Nylon Bushing 3"ID x 4"OD x 3-3/8" Long 3 910-0071.
Model 7200 -37- This Page Intentionally Blank.
Model 7200 -38- BOX, AUGERS & SIDE SHAFT.
Model 7200 -39- KEY PART NO. DESCRIPTION 1 901-3701 5570 Main Welded Body 2 929-3801 Hydraulic Hose Holder Spring 3 956-3803 Square Tube Jack 3A 956-3803-12 Jack Mount Tube 4 955-3701 Hydraulic Hose 1.
Model 7200 -40- UNLOADING GATE AND GATE INDICATOR.
Model 7200 -41- KEY PART NO . DESCRIPTION 1 955-0010 Hydraulic Cylinder-Center Lift 2 55-0092 Street Elbow ½" M x 3/8" Female 3 955-0010-1 3/8 x 28" Hydraulic Pipe 4 955-3605 3/8 x 90 .
Model 7200 -42- SPINNERS & GEARBOX SHAFT DRIVE.
Model 7200 -43- KEY PART NO . DESCRIPTION 1 901-3834-1 RH, 4-Point Paddle 3/8" 4/6-Per RH Spinner (Lower) 2-Per LH (Upper) 901-3834-1-AR Optional AR400 RH, 4-Point Paddle 3/8" 4/6-Per RH Spi.
Model 7200 -44- KEY PART NO. DESCRIPTION 1 19-0029-2 Casting, Machined (Thru Holes) 2 19-0029-1 Casting, Machined (Tapped Holes) 3 19-0029-3 Assy, Pinion Shaft/Gear 4 19-0029-4 Assy, Cross Shaft/Gear .
Model 7200 -45- SPINNER GEAR REDUCER - CENTER (1:1) #19-0030 KEY PART NO. DESCRIPTION 1 19-0029-2 Casting, Machined (Thru Holes) 2 19-0029-1 Casting, Machined (Tapped Holes) 3 19-0029-3 Assy, Pinion S.
Model 7200 -46- CORNER GEAR REDUCER - RIGHT HAND IMPORTANT! USE #80-90 WT. GEAR LUBE OIL ONLY . DO NOT USE GREASE FOR LUBRICANT. OUTPUT INPUT KEY 1000 RPM DRIVE PART NO.
Model 7200 -47- HUBS, AXLE & TANDEM ASSEMBLY KEY PART NO. DESCRIPTION 1 75-0211 Hub Assembly Complete 15,000# 2 75-0211-2 Seal 3 75-0211-3 Bearing Cone 4 75-0211-4 Bearing Cup 5 75-0208-5 Bearing .
Model 7200 -48- LADDER, THIRD AUGER, GATE INDICATOR & LIGHTING 25.
Model 7200 -49- KEY PART NO . DESCRIPTION 1 924-3712-1 Lower Front Dust Cover 924-3712-1-TR Truck Mount Front Dust Cover 2 924-3762-2 Front Dust Cover Hinge 3 901-3713-1 Gate Indicator Pipe 4 925-3762.
Model 7200 -50- See Page 52 For Oiler Instructions OIL-KIT 35.
Model 7200 -51- KEY PART NO. OEM PART NO. DESCRIPTION 1 952-0001-1-1 1001-6-B Oiler Body 6 Port Black 2 952-0001-1-2 1518-B Adj End Cap Oil Black 3 952-0001-1-3 4511 Plunger, Brass Adj End Cap 4 952-0.
Model 7200 -52- INSTRUCTIONS FOR AUTOMATIC CHAIN OILER WARNING: DISCONNECT PTO DRIVE SHAFT AND HYDRAULIC HOSES (RELIEVE HYDRAULIC PRESSURE) BEFORE CLEANING, ADJUSTING, LUBRICATING OR SERVICING THIS SPREADER. FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Model 7200 -53- SYMPTOM PROBLEM SOLUTION AUGERS Augers shake or chatter Stiff roller chains - dry Loose roller chains Worn sprockets/chain Dry auger trough Lubricate roller chains Tighten roller chain.
Model 7200 -54- DATE SERVICE PERFORMED DATE SERVICE PERFORMED MEYER INDUSTRIAL SPREADER “MAINTENANCE RECORD” Model No.____________________ Serial No.
Model 7200 -55- MEYER EQUIPMENT WHEEL TORQUE BOLT/STUD SIZE SOCKET SIZE PRESS FORMED WHEEL CENTER BOLT TYPE HEAVY DUTY WHEEL CENTER ½ 3/4 80 ft lbs Lug Bolt 85 ft lbs 9/16 7/8 80 ft lbs Lug Bolt 120 .
Model 7200 -56- This Page Intentionally Blank.
Model 7200 -57- This Page Intentionally Blank.
Model 7200 -58- This Page Intentionally Blank.
Model 7200 -59- Manufactured by: Meyer Mfg. Corp . County Hwy. A West P.O. Box 405 Dorchester, Wisconsin 54425-0405 Phone 715-654-5132 · FAX 715-654-5513 1-800-325-9103 www.meyermfg.com E-mail: sales @meyermfg.com Farm Equipment Buyers Trust the Name Meyer! Standard Equipment Specifications Model 7200 Bushels 550 (no ht.
A.
Ein wichtiger Punkt beim Kauf des Geräts Meyer 7200 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Meyer 7200 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Meyer 7200 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Meyer 7200 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Meyer 7200 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Meyer 7200 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Meyer 7200 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Meyer 7200. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Meyer 7200 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
