Benutzeranleitung / Produktwartung X-3200 des Produzenten Argox
Zur Seite of 124
I Argox websi te: http://www .argox.com X-1000VL X- 2000V / X-200 0V Zip X-2300E / X -2300ZE X- 32 00 / X - 3200Z X-3200E / X -3200ZE Xellent Serie s Industrial Barcode Printer User ’s Manual.
II T able of Contents 1. Getting St arted 5 Unpacking 5 Connecting the Power Cord 8 Internal Parts and Features 10 Loading Ribbon 13 Switching Ribbon Wou nd Ink-side in or Ink -si de out 17 Loading Media 19 S tandard Mode Loading Media 20 Peel Off Mod e Loading Media 24 Cutter Mode Loading Media 28 Adjust Position of Label Sensor 31 2.
III Installing a Printer Driver (f or other interfaces except USB ) 62 4. T roubleshooting 69 LED and LCD Diagnosis 69 Media Problems 69 Ribbon Problems 70 Other Problems 70 Printer S tatus 71 T ran s.
IV 6. T echnical Reference 109 General S pecifications 109 Printer Programming Language A, PPLA 1 13 Printer Programming Language B, PPLB 1 14 Printer Programming Language Z, PPLZ 1 16 Interface S pec.
5 1. Getting Starte d Congratulations on choosing the Ar gox Xellent Serie s (X -Series) industrial barcode prin ter. This user’s manual describing the Xellent Series prin ter models, wi ll help you get to know your new printer.
6 possible dama ge. 2. Open the top cov er of the printe r to see if the me dia compartments are in order. Note: If damage has occurred , contact your shippin g company immediately to file a claim. 3. Check whether y ou have receiv ed the followi ng accessories to gether wi th the printer.
7 Package Content s P rinter P ower Cord Qui ck Guide C ore for Ribbon CD Rom (incl uding software and user’ s manuals) U SB Cable 1 ” ID Core for Ribbon Power Cord Printer CD .
8 Connecting the Po wer Cord Before setting up and connecting the printer y ou should consider the followi ng . WARN ING! Do not operate the p rinter in an area where it mi ght get wet. Find a solid flat su rface w ith adequate roo m for the printer and enough space abov e f or medi a and ribbon a ccess.
9 Connect the pow er cord as below ..
10 Internal Pa rts and F eatures Ribbon Pick-up Spindle Ribbon Supply Spindle Media Supply Spindle Bracket Thermal Print Head Feed Slot.
11 S tandard Mode Head Latch Paper Sensor Guide Paper Roller Thermal Print Head.
12 Peel Off Mode Cutt er Mode.
13 Loading Ribbon Note: Thermal Transfer printing requires medi a to print with appropriate ribbon. Th is sectio n can be re ferred to, for X-Series to use transfer the rmal printing. The sa mple steps below are based on ribbon w ound ink-side in as an example .
14 3. Unwrap the ribbon and separate the ribbon roll from the bare core. Insert the ribbon roll onto th e ribbon su pply spindle. (Figure 3) Bracket 2 Head Latch 3 Ribbon Supply Spindle.
15 4. Lead the ribbon throu gh the print head module. (Fi gure 4) 5. Attach the ed ge of the ribb on onto the bare core and w ind it a bit onto the co re.
16 6. Insert the core onto the ribb on pick-up spindle. (Figu re 5) 7. Turn the pick-up spindl e to ensure the ribbon is ti ghtly wound. Ribbon Pick-up Spindle 5 Ribbon Pick-up Spindle.
17 Switching Ribbon Wound Ink-side in or Ink -side out The printer i s produced to suit flexible appl ications, no matter wi th ribbon wound ink-side in (manufactu ring defaul t), or with ribbon wound ink-side ou t. The steps to sw itch for ribbon wound ink-side out are listed as follow s: 1 .
18 2. After the adjustmen t abov e, ribbon wound ink-side out can be used. Then instal l the ribbon : 3. If ribbon wou nd ink-side in is in use, p ull and m ove the SHAFT RIBBON ADJ to “Inside” .
19 Loading Media The X-Series printe rs offer three di fferent loading modes : standard, peel-of f, or with a cu tter. S tandard mode allow s you to collect ea ch label free ly. P eel -off mode peel s backing material aw ay from the l abel as it prints.
20 Standard Mode Lo a d i n g M e d ia 1. Insert the media roll into the medi a supply spindle and move the media guide to the inside. (Figure 1) 1 Media Guide Media Supply Spindle.
21 2. Turn the head latch counter-cloc kwise and open the bracket. Remov e the outside media guide. (Figur e 2) 3. Lead the media through the print head modul e an d unde r the paper sensor guide.
22 4. Return the outside media guide, close the bra cket, and hook the head latch. (Fi gure 4) 4 Head Latch Outside Media Guide Bracket 3 Print Head Module Paper Sensor Guide Module Paper Sensor Posit.
23 5. Close the top cov er and the front access door and turn on the printer, or press the “FEE D” button i f the pr inter is already on. (Figu re 5) 5.
24 Peel Off Mode Lo a di n g Me d i a Follow steps 1 to 3 in “Standa rd Mode Loading Medi a ” above. 1. From the leadi ng end of the media roll remov e enough labels to expose 6-inche s of backin g paper.
25 2. Lead the media backing paper throu gh the print h ead module. (Fi gure 2) 3. Push down the peel -off mechanism relea se lev er and lead the media unde r the peeler modul e.
26 4. Close the peel er modul e using the peel -off mechanism release lever. (Figu re 4) 5. Close the top access door and turn on the printe r or press the FEED bu tton if the printe r is already on.
27 Notes: 1. The FEED button does not ma ke the printer peel. To enable Peeli ng function, set by the LCD p anel . 2. Make sure the peeler senso r is out o f the ribbon path when instal led.
28 Cutter Mo d e L o a di n g M e di a Follow steps 1 to 3 in “ Standard M ode Loading Medi a ” above. 1. Insert the media into the print head module and u nder the paper sensor guide .
29 2. Return the outside media guide, close the bra cket, and hook the head la tch. (Figure 2) 2 Outside Media Guide Bracket Head Latch.
30 3. Close the top access door and turn on the printer or press the FEE D button if the printer is already on. The p rinter w ill then feed the label s through the cut ter automa tically. (Figure 3) Note: The FEED but ton does not ma ke the printer cut.
31 Adjust Position of Label Sensor Function of the l abel sen sor is to de tect the g ap, notch, or holes of labels, to help the printer for accurate print posi tions and label length. For label s with ga ps, label sensor can be posi tioned wherever media locates .
32 2. Printer Operation The illustrations below describe parts and features o f X -Series . Front Panel T op Access Door Front A ccess Door X-1000VL LEDs and Buttons LCD Display X-2000V X-2000V Zip X-.
33 The front panel incl udes: 3 LED indicators (READY , MEDIA and RIBBON ) 3 buttons (FEED , PAUSE and CANCEL) LCD display (except X-1000V L) Top Access Doo r Front Access Doo r LED Indicators There are three LED indicators on the front pane l - READY, MEDIA and R IBBON.
34 direct thermal can be set via the prin ter panel. For the X- 100 0VL model , s et vi a Printer Utility , Windows driver or printer commands . Buttons There are three buttons, each w ith two basic functions.
35 LCD Disp l a y The X-2000V / X-2000 V Zip / X-2300E / X-2300ZE / X-3200 / X-3200Z / X-3200E / X-3200ZE models hav e a L CD that show s: printer status printer settin gs input data from .
36 If a keyboard i s plugged in, the LCD display w ill indicate: X-2000V / X-2000V Zip / X-2300E / X- 2300ZE X-3200 / X-3200Z / X-3200E / X- 3200ZE If a barcode reader is connected, the LC D displa y .
37 Setting Display Language The printer’s LCD display supports six languages: En glish, French, German, Italian, Spa nish, and Portugues e. Item Range Factory Default LANGUAGE ENGLISH, FRENCH , GERM AN, ITALIAN, SPANISH, PORTUGUESE , SIMPLIFIED CHINESE ENGLISH To select a lan guage: 1.
38 Changing Settin gs from the Pane l You may chan ge settings usin g the buttons on the front panel of the X-2000V, X-2000 V Zip, X-2300E , X-2300ZE, X-3200, X-3200Z, X-3200E, and X-3200ZE printe r models , in addition to changing settings via softw are commands.
39 LCD Function Setting Proce dure The following procedure is an example of setting procedure to direct thermal printing mode: L CD indicating LCD setting s tep s READY (203,PPLB) After p rinter pow er in on, LCD wi ll indicate as shown at the le ft. S tep 1 Press both P AUSE + CAN CEL buttons.
40 Printer LCD function settings and para meters: Item Range Factory Default Remarks PRINT MODE DIRECT THERMAL/ THERM. TRANSFER THERM. TRANSFER AUTO-CAL. MODE MODE 1 MODE 2 MODE 3 MODE 4 MODE 1 Mode 1: Printer performs Auto Calibration after printing the first label, if label height diff ers from param eters in printer's flash.
41 ALTERNATIVE 2 ALTERNATIVE 3 CUT PEEL OFFSET -15 ~ 50 mm 0 mm To adjust cut and pe el positions. PRINT OFFSET -8 ~ 15 mm 0 mm Controls vertical pri nt positions. Positive va lue onl y. For X-2000V onl y. TPH VER OFFSET -9~9 mm (PPLA/PPLB) -3~3 mm (PPLZ) 0 mm To adjust offs et of vertical print position.
42 CUT MODE NORMAL CUTTER W /O BACK NORMAL Available only when CUTTER INST ALLED is set to “YES”. PEELER INSTALLED NO YES NO READER INSTALLED NO YES NO Available only in PPLB printer language. W IN. CON. LEN. 0 ~ 254 mm 0 mm Available only in W indow s with bundled printer driver and for continuous media.
43 enters BACK DISTANCE setting. BACK DISTANCE 10~40 mm 21 mm Available only when BACK FEED is enabled. BASE DARKNESS 0~99 (PPLA) -28~28 (PPLB) 0 Available only in PPLA and PPLB printer languages. ABS. DARKNESS 0~30 0 To select dark ness. Available only in PPLZ printer language.
44 SETTING PRIORIT Y COMMAND/ LCD PANEL COMMAND Choosing priorit y of LCD settings. It decides which setting method - by comm and or by LCD panel, is prior.
45 GATEW AY DHCP setting is disa bled. On the contrary , DHCP setting is enabled. 1. FEED/CONFIG . : change contents. (ex. from 000.000.000 .000 to 255.255.255.255) 2. P AUS E/CALIBR. : shift “_”sign position. (ex. from 255.255. 255.255 to 255.255.
46 Media Calibration After the media is lo aded, please pe rform media c alibration to calibrate the label sensor in adv ance. 1. Turn off the printe r 2. Press and hold the PA USE button and turn on the pow er. 3. When “CALIBR ATION …” is displ ayed on the L CD, and both READY and M EDIA indi cators blink, release the PAUSE button.
47 Printing a Confi guration Report To perform a sel f -test and print a con figuration re port, helping to check printer’s print quality and internal settin gs. Steps as below : 1. Turn off the printe r. 2. Load media and ribbon . 3. Press and hold the FEE D bu t ton w hile turning on the power.
48 Sample of Con figuratio n Report – based on X -2300E:.
49 1. Firmware V ersion Information 2. S tandard RAM Siz e 3. A vailable RAM Size 4. Flash T ype 5. A vailable Fl ash Size 6. Font Symbol Set 7. Print Mode ( Thermal T ransfer or Direct T hermal) 8. Sensor type (See- Through or Re flective) 9. Label -less Calibration V al ue 10.
50 32. Mac Address 33. SNMP 34. DIP switch Switch ON OFF 2 Direct Thermal Default 35. Font Image Remark ： What continue after the p arameters a re tes t pa tterns of print head .
51 Resetting to Factor y Defaul t Settings To reset the pri nter to fa ctory default se ttings: 1. Turn off the printe r. 2. Press and hold the CANC EL button and turn on the printer. 3. When “RESE T …” is displ ayed on the LCD and the REA DY indicator blinks , release the CAN CEL button.
52 3. Computer Conne ctions This printer co mes wi th USB interface, a standard Centroni cs parallel inter face, and a nine -pin Electronics Indu stries Association (EIA) RS -232 serial da ta interface. USB Interface Requirement s The Univ ersal Serial Bus (USB) inter face is comp atible w ith your existing PC hardw are.
53 Serial (RS -23 2) Port The required cable must hav e a nine-pin "D" type male conne ctor on one end, whi ch is plugged into serial port located on the back of the printer. The other end of the cable connect s to a serial por t on the host compute r.
54 Ethernet 10/100 Int ernal Printer Ser ver Option X-2300E / X-2300ZE / X-3200E / X-3200ZE mode ls provide Ethernet inter face (RJ45), whi ch allows host in a local area network to conv enient ly use several printe rs by Etherne t connectivi ty at the same time.
55 Ethernet indication: Amber LED Green LED Centronics Pa rallel USB PS/2 RS232 Serial Power Sw itch AC Pow er Jack Ethernet.
56 Communicating w ith the Printer The bundled p rinter driv er can be applied to all appl ications under Windows XP/ Vis ta/ W in dows 7/ W indow s 8 , sup porting 32-bit/ 64 -bit operation sy stems.
57 1. Tu r n of f the printer . Plug the pow er cable into the pow er socket on the w all, and then connect the other en d of the cable to printe r's power socke t. Connect the US B cable to the USB port on the p rinter and on the PC. 2. Tu r n on the printer .
58 4. Choose Industrial Barcode Printers on the screen, go to X-3200 product p age, cli ck on version o f Seagull driv er and then sta rt install ation :.
59 Instead of the flash prompt abov e, another w ay to install Seagull driver is to run the Driv er W izard u tility from the Installation Direc tory where the Sea gull driver file s locates. 5. On the Seagull Driv er W iz ard prompt, select the first radio button to “Ins tall a d river for a Plu g and Play printer”: Then click “Nex t.
60 6. Enter Printer na me (i.e. Argox X- 3200 PPLB ) and select "do not share this p rinter ”, and click "Nex t" 7. Check all the data on the show ing screen, i f it is correct, cli ck "Finish".
61 8. After the related files have been copied to y our system, cli ck "Finish". 9. After driver ins tallation is comple te, click "Close".
62 Installing a Prin ter Driv er (for other interfa ces except USB) 1. T urn of f the printer . Plu g the power cable int o the pow er socket on the w all, and then connect the other en d of the cable to printe r's power socke t.
63 3. Choose Industrial Bar code Pri nters on the sc reen, go to X-3200 product p age , click on version o f Seagull driver and then sta rt install ation:.
64 Instead of the flash prompt abov e, another w ay to install Seagull driver is to run the Driv er W izard u tility from the Installation Direc tory where the Sea g ull driv er files locates . 4. On the prompt , W indow s Printer Driver, select “I accept… ” and click "Next" .
65 6. Click "Finish". 7. Select Install printe r drivers and Click "Nex t".
66 8. Select model & e mulation - the follow ing examples are based on model X- 320 0 PPLB: 9. Select the port o f the printer and click "Nex t".
67 10. Enter Printer name (i.e. Argox X- 320 0 PPLB) an d select "do not share thi s printer”, and cli ck "Next". 11. Check all the data on the show ing screen, if it is correct, cli ck "Finish".
68 12. After the rel ated files have been copied to y our system, cl ick "Finish". 13. After driver ins t allation is comple t e, click "Cl ose".
69 4. Troublesho oting Normally, if the printer is in not working prope rly, the " READY " LED blinks continuousl y, and printing and com munication between the host and printer stops. LED and LCD Diagn osis Blinking LEDs indi cate a problem.
70 Ribbon Problems LED/LCD Indication READY and RIBB ON LEDs Blinking LCD Displ ay RIBBON OU T Possible Proble ms Solutions Remarks Ribbon out Supply the ribbon roll Not applicable to di rect thermal.
71 Cutter failed Check the media. Check the connection between cutter and main board. Call for service. Memory full Check graphics and soft fonts from host. Del ete by application so ftware for those no lon ger in use . Need to reboo t the system.
72 graphics or form s. Check data form at. Call for service. SENSOR O.R. READY Media calibration is out of range for sens or detection. Make sure m edia is loaded and media sensor locates under media. PRINT HEAD HEAT MED IA Printing job will start until the temperature of TPH goes down.
73 Printer Mainte nance Vertical strea ks in the printout usually ind icate a dirty or faul ty print head. (Refer to the following examples.) Clea n the print head . If the problem persists , replace the print head. For unstable ribbon roll rotation, chec k the label p ath and make sure the head latch is securely closed.
74 Cleaning the Print Head To keep the Pri nt Head remain in the best condi tions and efficiency and to extend dura tion for use , regular clea ning action is needed . Note: Turn off the printe r before cleaning. Clean the print head as foll ows: 1. Turn off the printe r.
75 It’s strongly recommended to wear hand glov es during cl ea ning progress. Do not touch print head surface by bare hands or with any hard equipment.
76 5. Advanced Installation and Adjustment This chapter desc ribes inst allation and adjustment procedu re for X series industrial printers. It’ s recommended to be carried ou t by technicians, in order to keep overal l printing perfo rmance.
77 B. Left Hand Side Enh ancement If the phenomena as show n in Fig. 3 been ob served, please tur n the Fine Adjus tment Knob counte r-clockwise slightl y then try printing again to justi fy th e prin ting quality i mprovement as shown in Fig.4. Repeat the sa me process until the prin ting quality is well balanced on bo th ends of the label .
78 Figure 3 Figure 4 Once the desired quality has been reache d, pleas e make note on the new setting o f the Fine Adjustment Knob and the type nu mber of ribbon been used in this printi ng tas k for future reference. [Remark]: Please note, as shown in Fig.
79 Print Head Print Line Position When the label onl y exhibits loca lly inferior p rinting quality and the ribbon is not w rinkled, the position of the print he ad shall be adjusted, and the adjusting position is sh own as Fig. 1. The v iewing direction is facin g the machi ne, and using hex socket screw driver for the adjustment .
80 Figure 1.
81 Figure 2 Figure 3.
82 Ribbon Tension Adjustment Both ribbon suppl y spindle and ribbon pickup spin dle are equipped with control knobs to adj ust ribbon tension . The c ontrol knobs can rotate to b oth directions . Rotate the control knob c lockwise to increase r ibbon tension; rotate it counter-clockwise to reduce ribbon tension.
83 Figure 1 Figure 2.
84 Printing Wrinkl e During printin g, ribbon may wrinkle and cause ab normal printing quality . The following describe s how to solv e ribbon wri nkle accordingly .
85 2. Make sure the Ribbon Br acket is at it s low est position first; then tight up the screw s by rot ating clockwi se. 3. Print a test pa ge to chec k print quality . If the quali ty is improved , stop the adjustmen t; if not, continue w ith next step.
86 4. If the test print appears a s Figure A, remain the sc rew at the right of Ribbon Brac ket fixed, then loose the screw at the left, and gradually fine-tune upward, until the print quality gets improved.
87 Rotary Cutter and Guillotine Cutter In stallation Refer to the following steps to install the cu tter kit onto p rinters: 1. Turn off the printer. 2.
88 5. Insert the left side of cutter b racket (7) and secure the tw o screws (6) to the print module. Rotary Cutter Guillotine Cutte r.
89 6. Thread the cutte r cable throu gh hole (8) and rout e it to the JP16 connector (CUTTER) on the X-1000V L/ X-2000V / X-2000V Zip main boards, or to the JP14 connect or (CUTTER) on the main board o f X-3200/ X-3200Z/ X-3200E/ X-3200ZE / X-2300E/ X- 2300ZE .
90 Rotary Cutter and Guillotine Cutter Se ttings Before printin g and cuttin g tas ks, please make sure whether the cutter in use is Ro tary Cutter , or Guill otine Cutter . Then select proper settings v ia Seagull D river for printer . The foll owing install ation steps a re bas ed on X-3200 as an exa mple.
91 3. “Cutter Setup” prompt s wi ll be indicated as bel ow . Check on th e radi o button, “Rot ary ” if there’ s Rota ry Cutter install ed. Then click “OK“ : Check on the radi o button, “Guill otine” if there’ s Guillotine Cutter install ed.
92 4. Go to “Printin g Preference ” prompt of CP -2140 driv er and then click on the “S tock” tag. C heck “Post - Print Action” se ttings and select “Cut”. ※ If there’ s Guillotine Cutte r instal led and pa rtial cut function is needed, select “P artial Cut” in “Pos t - Print Action”.
93 Rotary Cutter w ith Paper Jam If there is p aper jam insi de rotary cutter , refer to Rot ary Cutter Install ation section to re move the rot ary cutte r . Check the Cam as marked in Figure 1, find a slotted screw driver to turn counter-clockw ise as Figure 2.
94 Guillotine Cutte r with Paper Jam If there is p aper jam inside guillotin e cutter , check i n Figure 1 and find where the screw under guillotine cutter . It is to control cut actions of guill otine cutter . Find a Phillips screwdriver to lay dow n the blade by turnin g the screw counter-clockwise.
95 Dispenser Installati on Install a dispenser into the printer as follows: 1. Turn off the printe r. 2. Remove the top cov er on both left and ri ght sides.
96 4. Con nect the Peeler sens or to main board JP15 socket o f X-1000VL, X-2000V , X-2000V Zip / JP12 socket o f X-3200, X-3200Z, X-320 0E, X-3200ZE , X-2300E, and X- 2300ZE . Secure the di spenser board on to printer case . 5. Insert the le ft side o f dispense r bracket and secur e the th ree screws to the TPH module.
97 6. Install the ribb on and medi a. 7. Turn on the printe r. 8. For the X-2000V / X-2000V Zi p/ X-3200/ X-3200Z/ X-3200E/ X-3200ZE/ X-2300E / X-2300ZE models, set the p arameter o f “DISPENSE R INSTALLED ” on the LCD to the ON position. For the X-1000VL , ignore this step.
98 RTC Batter y Replacement 1. T urn o ff the printer; disco nnect the AC power cable. 2. Open the lef t cover o f printer . 3. Loose the lock for R TC Batte ry on m ain board and then replac e with a known good R TC battery . CAUT ION: Risk o f ex plosion if battery is replaced by an incorrect ty pe.
99 Stand -alone w ith Ke y board This section cov ers stand-alone opera tion wi th keyboard. It is applicable w ith printer mod els: A rgokee PS/2 Keybo ard Printer Language PPLA PPLB Basic PPLB only .
100 Form Control Functions: Key Function Esc Enter or exit fro m keyboard mode Backspace Delete the last ty ped characte r F1 Next form i f more than o ne form exi sts Enter - Select the form - End of.
101 Example: Making a Keyboard Form 1. Make a command file for the form, KBD.FRM. Command Description ZS FK"KBDFORM " FS"KBDFORM " V00,15,N,"Produc t Name ?" C0,10,N,+1,"Produc t No.
102 3. Turn off the printe r, connect the keyboard and then turn on the printer. The LCD displ ays this message : READY (203,PP LB) <ESC> FOR KEY BD 4. Press <ESC> to en ter the key board mode and th e form name appears. Pres s <ENTER> to select the for m.
103 7. Press <ENTER> to continue to the next label and repeat steps 5 ~ 7, o r <ESC> to exit. 8. Output: ENTER to go on , Or ESC to re turn.
104.
105 Stand -alone w ith Barcode Reader This section cov ers stand-alone opera tion wi th barcode readers. It is applicable wi th printer models: Barcode Reader Interface PS/2 RS - 232 Printer Language .
106 Example: Making a Barcode Reader Form 1. Make a command file for a form, READER .FRM. Command Description ZS FK"READE R" FS"READE R" V00,15,N,"Produc t Name ?" C0,10,N,+1,"Produc t No.
107 2. Send the file REA DER.FRM to printer under M S -DOS >COPY/B REA DER.FRM LPT1: 3. Turn off the printe r, connect the ba rcode reade r, turn on the printer and set “ Reader installed ” on the LCD to ON position. 4. The form REA DER is automatical ly ex ecuted.
108 Notes: 1. To return to nor mal oper ation, press and hol d the CAN CEL button and turn on the printer a gain. 2. When using a keyboard or barcode reader co mmunicating with a host throu gh the Cen tronics or serial po rt is prohibited.
109 6. Technical Referenc e General Specificati ons X-1000VL X- 2000V X-2000V Zip X- 2300E X- 2300ZE X- 3200 X- 3200Z X- 3200E X- 3200ZE Printing Method Direct Thermal an d Thermal Transfer Printing Resolution 203 dpi (8 dots/mm) 300 dpi (12dots/mm) Printing Width Max 4.
1 10 Display LED indicator x 3, Button x 3 LED indicator x 3, Button x 3, Back-lit LCD Displ ay 16 x 2-line Multili ngual Communic ation interfaces Centronics parallel, RS - 232 serial (baud rate to 1.
111 Compact Size W250 x L418 x H26 3 mm Weight 24lbs(11kgs) Power Source 100~240 VAC, 50/60 Hz, internal univ ersal power supply Operation Environment Operating Te mperature 40 F~100 F (4 .
1 12 Note: 1. Since Font Ca rd and optio nal RTC Card share the same sl ot on X-1000VL and X-2000V , they cannot be used at the same time. 2. The X Series models, ex cept X-1000VL, can c onnect to PC keyboard via PS /2 port for s tandalone operatio n.
1 13 Fonts, Bar Codes and Graphi cs Specification The specifications of fonts, ba r codes and gr aphic s depends on the printer e mulation. T he e m ulation is a printe r pro gramming l anguage through w hich the host can communi cate with your p rinter.
1 14 Code 93 Postnet UCC/EAN-128 UCC/EAN-128 K-MART UCC/EAN-128 R andom Weight T elepen FIM Interleave 2 of 5 (S tandard/with m odulo 10 checksum/with hum an readable check digit/with modulo 10 check .
1 15 Character Rotati on 0, 90, 180, 270 degre e, 4 direction rotation Soft Fonts True Type fonts can be downloaded by Font Utility (Two-byte Asian fonts a lso can be download ed to X- 3200 / X -2300E.
1 16 Composite Codes Aztec Barcode Graphics PCX , Binar y Raster, BMP and GDI Printer Programming Language Z, PPLZ Specification X- 2000V Zip / X-3200Z / X-2300ZE / X- 3200ZE Internal Fonts 8 (A~H) fonts with different point size. 8 AGF A fonts: 7 (P~V) fonts with fixed different point size (not scalable) .
1 17 GS1 Data bar (RSS) Industrial 2 of 5 S tandard 2 of 5 Logmars 2D Bar Code Types MaxiCode PDF417 Data Matrix (ECC 2 00 only) QR code Composite Codes Aztec Barcode Micro PDF417 Graphics GRF, Hex an.
1 18 Interface Specifica tions This section presen ts the inter face specifications o f IO ports for the printer. These incl ude pin assi gnments, protocol s and detail ed information abou t how to prope rly inter face your printer with your host or terminal .
1 19 Serial In t er f a ce The RS-232 connecto r on the printe r side is a female, DB- 9. Pin Signal Description 1 No function Shorted to Pi n - 6 2 Receiv ed Data, RxD Input. Serial “Received Dat a” 3 T r ansmi tted Dat a, TxD Output. Serial “T ransmitt ed Data”.
120 Connection with Host : Host 25S Printer 9P Host 9S Printer 9P (PC or compatibl e) (P C or comp atible) DTR 20 …… 1 DSR DTR 4 …… 1 DSR DSR 6 …… 6 DTR DSR 6 …… 6 DTR TX 2 …… 2 RX.
121 The simplest w ay to conne ct to other hosts (not PC compa tible) or terminals is: Printer Terminal/Host Pin 2- RxData ……… TxData Pin 3- TxData ……… RxData Pin 5- Ground ……… Ground In general, as long as the da ta quantity is not too large and y ou use Xon/Xoff as flow control, i t will be problem free.
122 Parallel (Centronics) The parallel por t is a stand ard 36-pin Centronics connector. Pin assignments are as follow s: Pin Direction Definition Pin Direction Definition 1 In /STROBE 13 Out SELECT 2.
123 Ethernet Interface The follow ing port complies wi th Ethernet commu nication. Auto Polling Both the serial port and pa rallel port o f this printer can be ac tive at the same time, i.e. the printer can simultaneousl y communicate with two PCs v ia different ports .
124 ASCII TABLE N UL 0 @ P ' P SOH XON ! 1 A Q a q STX " 2 B R b r XOFF # 3 C S c s $ 4 D T d t NAK % 5 E U e u ACK & 6 F V f v BEL ‛ 7 G W g w BS ( 8 H X h x ) 9 I Y i y LF * : J Z j z ESC + ; K [ k { FF , < L l I CR - = M ] m } SO RS .
Ein wichtiger Punkt beim Kauf des Geräts Argox X-3200 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Argox X-3200 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Argox X-3200 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Argox X-3200 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Argox X-3200 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Argox X-3200 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Argox X-3200 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Argox X-3200. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Argox X-3200 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
