Benutzeranleitung / Produktwartung TE653ELW-M des Produzenten Meade
Zur Seite of 24
TE653ELW-M Complete Weather Forecaster with Indoor/ Outdoor Temperature and Humidity USER MANUAL MADE IN CHINA.
INTRODUCTION Thank you for selecting a Meade Instruments W eather Forecaster . This device combines precise time keeping, monitoring and displaying of current temperature data from up to three remote locations (additional sensors are required).
INST ALLA TION Communications between the main unit (receiver) and the remote sensor (transmitter) is wireless. This allows you to greater flexibility in choosing the location of remote sensor . The remote transmits data up to 164 feet (50 meters) over an open, unobstructed area.
4 REMOTE SENSOR FEATURES • Remote temperature transmission to the main unit via 433 MHz signal • Case can be wall mounted using built-in hanger • 164 feet transmission range without interference.
PLACEMENT • The remote sensor should be placed under eaves or a similar location with free air circulation, sheltered from direct sunlight and extreme weather . • Ideally , place the remote sensor over soil, rather than asphalt, which would cause false readings.
FRONT REAR 6 MADE IN CHINA A H G F E B L I D J K C M N O.
A. WEA THER FORECAST/ PRESSURE window B. TEMPERA TURE/ HUMIDITY window C. CLOCK window D. DOWN button • Select the next available mode • Press and hold for 2 seconds to search for wireless signal from remote sensor .
BA TTERY INST ALLA TION • Remove the battery door located at the back of the main unit. • Insert two (2) AA batteries and replace the battery compartment door . PLACEMENT • Make sure that the main unit is locating within the operating range of all remote sensors.
PRESSURE OPERA TION The pressure window displays: current barometric pressure, sea level pressure, and weather forecast. The information contains a number of historical statistics: pressure/ temperature/ humidity history bar -chart for the past 24 hours.
New Moon W aning Crescent First Quarter W axing Gibbous Full Moon W aning Gibbous Last Quarter W aning Crescent CHANGING PRESSURE AND ALTITUDE UNITS • Press MODE as needed, until “LOCAL” pressure is displayed. • Press and hold HISTOR Y , until the pressure unit is flashing.
Icon Status Searching for the signals from the remote sensor Corresponding remote sensor signal received successfully No signals received for over 1 hour REMOTE SENSORS ST A TUS The wave icon above th.
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button recalling: • Current temperature and humidity • Minimum temperature and humidity • Maximum temperature and humidity at the remote location.
ICON Atomic Time Reception Strength Undefined data (Flashing) No Reception for the past 24 hours W eak signal, but can be decoded Strong signal • The atomic clock receiver is programmed that it will search for the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00 am.
CLOCK ALARMS There are two time alarms – Weekday alarm ( W ) and Single day alarm ( S ) - and one Ice Warning Alarm ( PRE-AL ). • If Weekday (W) alarm is activated, it will sound at the set time a.
Issue Main unit Radio Controlled T ime signal is not received Cannot locate remote sensor Cannot change the channel Data does not match data on the main unit Place unit by the window and keep it there.
BA TTERY INST ALLA TION • Remove the battery door located at the back of the main unit. • Insert two (2) AA batteries and replace the battery compartment door . PLACEMENT • Make sure that the main unit is locating within the operating range of all remote sensors.
PRESSURE OPERA TION The pressure window displays: current barometric pressure, sea level pressure, and weather forecast. The information contains a number of historical statistics: pressure/ temperature/ humidity history bar -chart for the past 24 hours.
New Moon W aning Crescent First Quarter W axing Gibbous Full Moon W aning Gibbous Last Quarter W aning Crescent CHANGING PRESSURE AND ALTITUDE UNITS • Press MODE as needed, until “LOCAL” pressure is displayed. • Press and hold HISTOR Y , until the pressure unit is flashing.
Icon Status Searching for the signals from the remote sensor Corresponding remote sensor signal received successfully No signals received for over 1 hour REMOTE SENSORS ST A TUS The wave icon above th.
VIEWING MAX/MIN AND MINIMUM READINNGS Press the MEMORY button recalling: • Current temperature and humidity • Minimum temperature and humidity • Maximum temperature and humidity at the remote location.
ICON Atomic Time Reception Strength Undefined data (Flashing) No Reception for the past 24 hours W eak signal, but can be decoded Strong signal • The atomic clock receiver is programmed that it will search for the atomic time signal daily for 0:00, 3:00, 6:00, and 12:00 am.
CLOCK ALARMS There are two time alarms – Weekday alarm ( W ) and Single day alarm ( S ) - and one Ice Warning Alarm ( PRE-AL ). • If Weekday (W) alarm is activated, it will sound at the set time a.
Issue Main unit Radio Controlled T ime signal is not received Cannot locate remote sensor Cannot change the channel Data does not match data on the main unit Place unit by the window and keep it there.
MADE IN CHINA Meade Instruments Corp. 27 Hubble Irvine, CA 92618 U.S.A. ©201 1 Meade Instruments Corp. All Rights Reserved. All user manual contents and information are subject to change.
Ein wichtiger Punkt beim Kauf des Geräts Meade TE653ELW-M (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Meade TE653ELW-M noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Meade TE653ELW-M - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Meade TE653ELW-M reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Meade TE653ELW-M erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Meade TE653ELW-M besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Meade TE653ELW-M verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Meade TE653ELW-M. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Meade TE653ELW-M gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
