Benutzeranleitung / Produktwartung MC-207 des Produzenten McIntosh
Zur Seite of 24
MC207 Owner ’ s Manual McIntosh Laboratory , Inc. 2 Chambers S treet Binghamton, New Y ork 13903-2699 Phone: 607-723-3512 F AX: 607-724-0549 Seven Channel Power Amplifier.
2 IMPOR T ANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERA TING THIS EQUIPMENT . W ARNING - T O REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT T O RAIN OR MOISTURE.
3 Y our decision to own this McIntosh MC207 Seven Chan- nel Power Amplifier ranks you at the very top among dis- criminating music listeners. Y ou now have “The Best.” The McIntosh dedication to “Quality ,” is assurance that you will receive many years of musical enjoyment from this unit.
4 Performance Features Connector Information, Introduction and Performance Features Introduction • • • • • Power Output The MC207 consists of seven Power Amplifier Channels, each capable of 200 watts into 4 ohm or 8 ohm Loudspeak- ers with less than 0.
5 Dimensions The following dimensions can assist in determining the best location for the MC207. There is additional informa- tion on the next page pertaining to installing the MC207 into cabinets. Dimensions 17- 1/2 " 44.45cm 8- 7/8 " 22.54cm Front View of the MC207 Rear View of the MC207 9- 7/16 " 23.
6 Inst allation The MC207 can be placed upright on a table or shelf, standing on its four feet. It also can be custom installed in a piece of furniture or cabinet of your choice. The four feet may be removed from the bottom of the MC207 when it is custom installed as outlined below .
7 Rear Panel Connections and Switch Connect the MC207 power cord to a live AC outlet. Refer to informa- tion on the back panel to determine the correct voltage MUL TI- CHANNEL INPUT ac- cepts a 25 con.
8 Caution: The supplied AC Power Cord should not be connected to the Rear Panel of the MC207 Amplifier until after the Loudspeaker Connections have been made.
9 How to Connect for Seven Channels Right Front Loudspeaker Left Front Loudspeaker Right Surround Loudspeaker Left Surround Loudspeaker Back Surround Loudspeaker Center Front Loudspeaker Back Surround.
10 Caution: The supplied AC Power Cord should not be connected to the Rear Panel of the MC207 Amplifier until after the Loudspeaker Connections have been made.
11 Right Front Loudspeaker Left Front Loudspeaker Right Surround Loudspeaker Left Surround Loudspeaker Center Front Loudspeaker To A C Outlet How to Connect for Five Channels.
12 Caution: The supplied AC Power Cord should not be connected to the Rear Panel of the MC207 Amplifier until after the Loudspeaker Connections have been made.
13 Left Channel (Zone B) Right Channel (Zone B) To A C Outlet How to Connect for T wo Channels (Zone B).
14 Front Panel Displays and Controls Remote On Indicator lights when the amplifier is in the Remote T urn-On Mode POWER GUARD LED lights when the Left Front Channel (1) POWER GUARD Circuit activates M.
15 How to Operate and Read the Power Output Meters How to Operate Power On W ith the POWER Switch set to the REMOTE Position, the MC207 will turn On or Off when an A/V Control Center turns On or Off. For manual operation, rotate the POWER Switch to the ON or OFF Position as desired.
16 McIntosh Laboratory , the company who introduced the world’ s first amplifier that could be called “High Fidelity”, has done it again. The McIntosh engineering staf f has cre- ated a power amplifier without compromise, using the most advanced McIntosh circuit design concepts.
17 T echnical Description higher distortion of many non-feedback designs. All transistors are selected to have nearly constant cur- rent gain over the entire current range they must cover . Output transistors in par- ticular , have matched uniform current gain, high current-bandwidth product and large active region safe operating area.
18 Figure 17 The MC207 can easily drive 4 ohm speakers, with their high current demand. Additionally , the MC207 can be used with 8 ohm speakers, and deliver equal power . McIntosh’ s new DPM TM design enables it to run on higher voltage rails when connected to less current-hungry 8 ohm speakers and still deliver 200 watts.
19 T echnical Description, con’t but the inaudible ultrasonic dis- tortion is also undesirable, since it can damage valuable Loudspeaker System tweet- ers. Y ou will never experi- ence the harsh and damaging distortion due to clipping. The Power Guard circuit is a waveform comparator , monitoring both the input and output wave- forms.
20 Figure 23 Control Center . When the A/V Control Center is switched On a digital “1” (+5V) signal operates the power relay in the MC207. The MC207 also has a remote Power Control input for Zone B operation (two of the seven channels).
21 Notes.
22 Specifications Specifications Power Output Minimum sine wave continuous average power output per channel, all channels operating is: 200 watts into a 4 ohm or 8 ohm load Rated Power Band 20Hz to 20,000Hz T otal Harmonic Distortion Maximum T otal Harmonic Distortion at any power level from 250 milliwatts to rated power output is: 0.
23 Packing Instructions Packing Instructions Quantity Part Number Description 1 034052 Shipping carton top 1 034051 Shipping carton bottom 2 034054 Foam Pad (top and bottom) 2 034186 Foam Pad (front a.
McIntosh Part No. 04089600 McIntosh Laboratory , Inc. 2 Chambers Street Binghamton, NY 13903 The continuous improvement of its products is the policy of McIntosh Laboratory Incorporated who reserve the right to improve design without notice. Printed in the U.
Ein wichtiger Punkt beim Kauf des Geräts McIntosh MC-207 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie McIntosh MC-207 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für McIntosh MC-207 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von McIntosh MC-207 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über McIntosh MC-207 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon McIntosh MC-207 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von McIntosh MC-207 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit McIntosh MC-207. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei McIntosh MC-207 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
