Benutzeranleitung / Produktwartung ELX8-60 des Produzenten Maxtor
Zur Seite of 69
ELX8 - 60 Installation Guide (v 1.0 a ).
FCC Compliance Statement Caution : Any changes or modifications in construction of this device which are not expressly approved the party re sponsible for compliance could void the user's authority to operate the equipment.
Important Notice 1. D o not p lace heavy objects on the top of the ELX8 - 60 . 2. ELX8 - 60 is not weatherproof. In case of outdoor use, equip a weatherproof case to protect ELX8 - 60 from water, moisture, or temperature (higher or lower than specificat ion s ).
ELX8 - 60 TABLE OF CONTENTS 4 2003. 08. 13 (v 1.0) Rugged CCTV OVERVIEW ................................................................................................................................................................ .. 7 1. What is ELX8 - 60? .
TABLE OF CONTENTS ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 5 8.3. Setting Recording Condition ................................................................................................ ......... 24 8.3.1. Configuration Status .................
ELX8 - 60 TABLE OF CONTENTS 6 2003. 08. 13 (v 1.0) Rugged CCTV 16.3. Uninstalling D VR Manager ................................................................................................ ........ 43 16.4. Configstation ...........................
OVERVIEW ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 7 OVERVIEW 1. What is ELX8 - 60 ? The ELX8 - 60 is an 8 - a nalog channel s network digital video recorder. Video, Audio, and Text Event - Logs are digitized and stored on two internal h ard - drives.
ELX8 - 60 OVERVIEW 8 2003. 08. 13 (v 1.0) Rugged CCTV 2. Supplied Accessories Unpack and check all the items as below. 1. ELX8 - 60 (1) 2. DC Power Supply (1) (110V~220V) 3. AC Power Cord (1) 4. CD - ROM (Including D VR Manager) (1) 5. Remote Controller (1) 6.
OVERVIEW ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 9 3. Description & Function ELX8 - 60 Front (1) LED (2) IEEE1394 connecter (3) Remote co ntroller receiver (4) USB connecter (5) Function button.
ELX8 - 60 OVERVIEW 10 2003. 08. 13 (v 1.0) Rugged CCTV ELX8 - 60 Rear (7) Power switch (8) Ethernet connector (9) BNC connector for Video input (10) Audio input / output connector (11) RS232 connecter.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 11 INSTALLATION AND CONNECTION 4. Connecting & Running ELX8 - 60 4.1. Connecting camera (1) Set video type (NTSC/PAL) by rear panel ’ s switch. (2) Connect CCTV camera to ELX8 - 60 with BNC cable as shown below .
ELX8 - 60 INSTALLATION AND CONNECTION 12 2003. 08. 13 (v 1.0) Rugged CCTV 4.2. Connecting Monitor (1) Connect CCTV monitor to ELX8 - 60 with BNC cable as shown below . <Note> ELX8 - 60 has two video output ports ; for Monito r and VCR. The output signals from the two ports are same and either port may be used .
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 13 4.4. Supplying Power (1) Connect power cable to ELX8 - 60 . (2) Turn on the power switch located on the ELX8 - 60 rear panel. <Note> Use the plug bracket to secure the power cable if needed.
ELX8 - 60 INSTALLATION AND CONNECTION 14 2003. 08. 13 (v 1.0) Rugged CCTV 5. Running OSD menu 5.1. Using menu P ress the [MENU] button to open the OSD Configuration Menu. (1) Main Menu T abs : The select ed tab is shown in blue and the related sub - menu s will be shown below the tab.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 15 5.2. Dialogue Box to Edit a Word There are two methods to set word. (1) Using number button Enter the related numbers in order of horizontal/vertical . ( For example, in order to select “ C ” , press [ 3 ] and [ 2 ] button s.
ELX8 - 60 INSTALLATION AND CONNECTION 16 2003. 08. 13 (v 1.0) Rugged CCTV (3) Function word The following symbols are for executing specific function s: ü 1#2.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 17 6. Setting remote controller 6.1. Setting remote control DIP switch Set the remote control DIP switch to “ ON .” 6.2. Setting ID of ELX8 - 60 When controlling sever al ELX8 - 60 s with one remote controller, set Remote Control ID as follow s .
ELX8 - 60 INSTALLATION AND CONNECTION 18 2003. 08. 13 (v 1.0) Rugged CCTV (4) Select “ Remote Control ID ,” and press the [ENETR] button. (5) Select a value using the [ / ] button s and press the [EXIT] button. (6) Press the [EXIT] button to exit the Settings Page and return to Monitor mode.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 19 6.5. Loading the batteries into remote controller Remote controller requires two AAA - type batteries. 1. Remove the battery cover. 2. Taking care that the poles(+/ - ) are correctly positioned 3.
ELX8 - 60 INSTALLATION AND CONNECTION 20 2003. 08. 13 (v 1.0) Rugged CCTV 7. ELX8 - 60 Configuration 7.1. Basic Configuration 7.2. Advanced Configuration.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 21 7.3. External Storage & Backup Configuration 7.4. Internet/Intranet Configuration.
ELX8 - 60 INSTALLATION AND CONNECTION 22 2003. 08. 13 (v 1.0) Rugged CCTV 8. ELX8 - 60 Basic Setti ng 8.1. Viewing Image After initial start - up, images from Ch.1~4 are disp l ayed in a quad - split screen. <Note> If user password is set, a prompt for entering the password will appear .
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 23 8.2. Setting Date & Time (1) Press [MENU] button, and select “ Quick Setup ” tab . (2) Select “ Date/Time ” and enter the Settings Page by pressing [ENTER]. 8.2.1. Time Zone (1) Select “ Time Zone ” and press [ENETR] button to configure .
ELX8 - 60 INSTALLATION AND CONNECT ION 24 2003. 08. 13 (v 1.0) Rugged CCTV 8.2.4. Time Format (1) Select “ Time Format ” using the [ / ] or the [ / ] button s and press [EN TE R]. (2) Two Time Format s are available ; ‘ MM/DD/YYYY ’ and ‘ YYYY/MM/DD ’ .
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 25 (1) Press [MENU] button, and select “ Quick Setup .” (2) Move to sub - menu by pres sing [ENTER] or the [ ] button. (3) Select “ Recording ” using the [ / ] button s and press the [ENTER] button.
ELX8 - 60 INSTALLATION AND CONNECTION 26 2003. 08. 13 (v 1.0) Rugged CCTV 8.3.3. Recording Speed/Quality (1) Select “ Recording Speed/Quality ” using [ / ] button s and press the [ENTER] button. (2) Select a value using th e [ / ] button .
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 27 9. Connecting and Configuring Sensor 9.1. Connecting Sensor Input To connect a sensor to S1 , fix the wire to “ S1 ” and “ G “ . <Note> Devices connected to the sensor input should have “ Dry contact .
ELX8 - 60 INSTALLATION AND CONNECTION 28 2003. 08. 13 (v 1.0) Rugged CCTV 9.2. Setting Sensor at OSD menu (1) After a sensor is connect ed, it can be activate d through the OSD Configuration menu. (2) Select the sensor number (S1, S2, etc.) and p ress the [Enter] button to configure.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 29 10. Connecting & Configuring Relay Out 10.1. Connecting Relay Out ELX8 - 60 has total four ports of Relay Out. To connect a device to “ O1 ,” connect the wires to two “ O1 ” s.
ELX8 - 60 INSTALLATION AND CONNECTION 30 2003. 08. 13 (v 1.0) Rugged CCTV 10.2. Configuring Relay Out Each r elay can be synchronized with a sensor input or with motion detection for each of the four time schedul es (Weekday (Day), Weekday (Night), Weekend (Day), Weekend (Night)).
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 31 11. Connecting External Device with Serial Port 11.1. Connecting Text Input Device (ATM / POS / Access Control) In addition to images, the ELX8 - 60 can record text data received from POS/ATM through the RS232 serial port.
ELX8 - 60 INSTALLATION AND CONNECTION 32 2003. 08. 13 (v 1.0) Rugged CCTV 12. Connecting & Configuring Serial Ports for Pan/Tilt/Zoom 12.1. Connecting Serial Port The ELX8 - 60 has most major PTZ protocols a l re ady pre - programmed . Makes and models not supported can still be controlled using the Transparent Protocol.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 33 12.2. Configuring Serial Port Configure PTZ serial ports and available modes at “ System / Serial Setup ” . After completing serial setup, configure base address and port for each channel under the “ Camera ” menu tab .
ELX8 - 60 INSTALLATION AND CONNECTION 34 2003. 08. 13 (v 1.0) Rugged CCTV <Note> Wire Handling Trimming Wire When connect ing a wire to a terminal block, follow the instructions below . Note the different types of wire that can be used. St r anded Wire : Peel o ff the wiring cover 8~10mm and solder it.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 35 If properly connected, the disk is recognized automatically as in the following picture. To c opy images, the process i s as follows: Set copy range ( up to 1 minute) à Select drive à Copy (press “Start”) .
ELX8 - 60 INSTALLATION AND CONNECTION 36 2003. 08. 13 (v 1.0) Rugged CCTV 14. Connecting External Storage 14.1. IEEE1394 Port ELX8 - 60 has two IEEE1394 ports for external storage device interface. With them, ELX8 - 60 can expand storage capacity up to 4TB.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 37 14.3. Availa ble HDD It is recommended to use the following HDD models with the ELX8 - 60 .
ELX8 - 60 INSTALLATION AND CONNECTION 38 2003. 08. 13 (v 1.0) Rugged CCTV (1) Press [ENTER] button at “ Select Disk ” . (2) Select new added HDD (indicated as “ [F] ” ) using [ / ] button and press [EXIT] button (3) Select “ Action ” using [ / ] button and press [EXIT] button.
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 39 <Note> 1. Supply power to ELX8 - 60 a fter connecting Ethernet cable to protect against electrical damage to ELX8 - 60. 2. Check cable connection status. 3. Check LED on ELX8 - 60 ’ s rear panel after supplying power.
ELX8 - 60 INSTALLATION AND CONNECTION 40 2003. 08. 13 (v 1.0) Rugged CCTV 15.2. Configuring ELX8 - 60 Network Information The following description is on based o n Ethernet connection . For more detailed information on the Network Settings Page , please refer to “ ELX8 - 60 OSD User ’ s Guide ” .
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 41 16. Using D VR Manager 16.1. PC System Requirements for running D VR Manager Minimal Requirements Recommended Requirements CPU.
ELX8 - 60 INST ALLATION AND CONNECTION 42 2003. 08. 13 (v 1.0) Rugged CCTV (4) Select which component s to install and press the “ Next ” button. (5) Browse and choose a d irectory if the default directory is not preferred. Click the “ Install ” button, after selecting a directory to install .
INSTALLATION AND CONNECTION ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 43 16.3. Uninstalling D VR Manager (1) Click Windows “ Start ” But ton. (2) Select and Click ‘ Uninstall ’ icon to run Uninstall Shield . (3) D VR Manager p rogram w ill be automatically deleted.
ELX8 - 60 INSTALLATION AND CONNECTION 44 2003. 08. 13 (v 1.0) Rugged CCTV 16.5. Monitor Cli ck the related icon and run the “ D VR Manager Monitor ” program.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 45 APPENDIX APPENDIX.
ELX8 - 60 APPENDIX 46 2003. 08. 13 (v 1.0) Rugged CCTV #1. HDD #1.1. Fundamental Notions & Terms ELX8 - 60 Storing Constructure (1) It is possible to connect 2 sets of HDD internally (Internal, ATA Interface) and 63 sets of HDD externally (External, 2 ports of IEEE1394).
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 47 Backup (1) Backup is possible only through IEEE1394 port, and HDD for backup should be formatted as FAT32 type. (Its type is indicated as [F] in Disk Manager.) Disk Manager (1) When HDD is added or deleted physically, Disk Manager runs automatically after rebooting.
ELX8 - 60 APPENDIX 48 2003. 08. 13 (v 1.0) Rugged CCTV (3) HDD Managing Command Format Format as ELX8 - 60 ’ s file system. Not available to PC file system. Add Add HDD for recording. Need to format. Add Used Add a HDD that has been used and formatted.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 49 Installing & Expanding Internal HDD Adding or replacing HDD should follow below process. (1) Turn off the power of ELX8 - 60. (2) Check whether the dip switches are set as illustrated below (3) Remove the 6 screws as illustrated below and pull up the cover from the rear part to open.
ELX8 - 60 APPENDIX 50 2003. 08. 13 (v 1.0) Rugged CCTV (5) Fix the HDD with provided screws. Connect power and data cables to HDD. Installing si ngle HDD Installing 2 HDDs Caution for HDD Management 1. Replacing ‘ SLAVE ’ HDD of internal 2 HDDs causes permanent data loss in the SLAVE HDD.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 51 (6) Connect HDD power cable to main PCB ASS ’ Y. Secure the HDD with screws. (7) Connect HDD cable ’ s connector to HDD as in the following picture.
ELX8 - 60 APPENDIX 52 2003. 08. 13 (v 1.0) Rugged CCTV When installing one primary disk (1) When power is supplied to ELX8 - 60, “ Disk Manager ” runs automatically after rebooting. If not, run it manually in “ Menu à Utility à Disk Ma nager ” .
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 53 Whe n installing one primary disk and auxiliary disk (1) When power is supplied to ELX8 - 60, “ Disk Manager ” runs automatically after rebooting. If not, run it manually in “ Menu à Utility à Disk Manager ” .
ELX8 - 60 APPENDIX 54 2003. 08. 13 (v 1.0) Rugged CCTV Expending External HDD (When using internal HDD as primary disk) ELX8 - 60 use IEEE1394 as external stora ge device interface, and has two ports of IEEE1394. ELX8 - 60 supports upto 4TB storage. <Note> 1.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 55 When using Disk Farm The following description is when ELX8 - 60 has internal primary disk and 3 se ts of IEEE1394 HDD. (1) When external HDD farm is connected to IEEE1394 port, “ Disk Manager ” runs automatically.
ELX8 - 60 APPENDIX 56 2003. 08. 13 (v 1.0) Rugged CCTV When using RAID The following description is when ELX8 - 60 has internal primary disk and 1 set of IEEE1394 HDD. <Note RAID> Even though several HDDs are connected to RAID, ELX8 - 60 will recognize t hem as only one HDD.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 57 Installing & Expending External HDD (When using external HDD as primary disk) When using Disk Farm The following description is when ELX8 - 60 does n ’ t have internal primary disk and 4 sets of IEEE1394 HDD.
ELX8 - 60 APPENDIX 58 2003. 08. 13 (v 1.0) Rugged CCTV is changed to [R]. (8) Select a third HDD of [*] Ext . Press the “ Apply ” button after selecting action as “ Format ” . Then [*] is changed to [R]. (9) Select a fourth H DD of [*] Ext . Press the “ Apply ” button after selecting action as “ Format ” .
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 59 (6) Press the [EXIT] button to shut down “ Disk Manager ” ..
ELX8 - 60 APPENDIX 60 2003. 08. 13 (v 1.0) Rugged CCTV #1.3. Replacing HDD Checking HDD ELX8 - 60 file system (VFS2) sensors bad sector automatically, and the sensored bad sector is not used. The following means when HDD is broken or has some problem in connection.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 61 #1.4. Keeping Data To keep the stored data, you should back up or reserve as HDD itself. Backup (1) Connect backup HDD to IEEE1394 port. (2) Go to playback mode with pressing the [Playback] button.
ELX8 - 60 APPENDIX 62 2003. 08. 13 (v 1.0) Rugged CCTV How to preserve as HDD itself To keep HDD itself, it is possible only when HDD is installed and used in ELX8 - 60 (including primary disk and RAID). And it is recommended to use external HDD instead of internal HDD.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 63 #2. Using CD - ROM Components of CD - ROM disc Installation Guide : ELX8 - 60 Installation Guide User ’ s Guide : ELX8 - 60 User ’ s Guide D VR Manager : D VR Manager User ’ s Guide ( ELX8 - 60 Remote Management Program) Acrobat Reader : V ersion 5.
ELX8 - 60 APPENDIX 64 2003. 08. 13 (v 1.0) Rugged CCTV #3. Specification General CPU 32bit RISC Processor (200MIPS) Flash Memory 8MB Main Memory 64MB OS Embedded LINUX Video Channel 8 Analog Channel (NTSC or PAL) Storage Device Internal 3.5 ” IDE HDD 2EA ( default 1EA) External 2EA for IEEE1394 Interface Support Max.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 65 Dis play Monitoring Max. 240/200ips (NTSC/PAL) Viewer 1ch, 4ch, 9ch, Auto Sequential Recording Performance Max. 60 ips for local channel : max 7.5 ips/channel Recording Resolution 720x243(NTSC), 720x288(PAL) Playback Performance Max.
ELX8 - 60 APPENDIX 66 2003. 08. 13 (v 1.0) Rugged CCTV PTZ Control Serial Port RS232(1), RS485(1)/ RS422(1) Control Method (Local) Front panel button & IR remote controlle r (control IP video chan.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 67 Mechanical Dimension (W D H) 306 x 280 x 67(mm) Weight 3.5Kg (With one HDD).
ELX8 - 60 APPENDIX 68 2003. 08. 13 (v 1.0) Rugged CCTV.
APPENDIX ELX8 - 60 Rugged CCTV 2003. 08. 13 (v 1.0) 69 Rugged CCTV 5327 Cedar Creek Dr. Kemp, Texas 75143 Tel : ( 866 ) 301 - 2288 Fax : ( 903 ) 498 - 8989 Technical Support: 1 - 866 - 301 - CCTV URL: www.rugged - cctv.com E - mail: sales@rugged - c ctv.
Ein wichtiger Punkt beim Kauf des Geräts Maxtor ELX8-60 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Maxtor ELX8-60 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Maxtor ELX8-60 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Maxtor ELX8-60 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Maxtor ELX8-60 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Maxtor ELX8-60 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Maxtor ELX8-60 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Maxtor ELX8-60. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Maxtor ELX8-60 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
