Benutzeranleitung / Produktwartung QM30 Series des Produzenten Manitowoc Ice
Zur Seite of 28
QM30 Series Ice Machines Installation, Use and Care, Manual Thank you for selecting a Manitowoc Ice Machine, the dependability leader in ice making equipment and related products. With proper care and maintenance, your new Manitowoc Ice Machine will provide you with many years of reliable and economical perform ance.
Safety Notices When using or servicing these Ice Machines, be sure to pay close attention to the safety notices in this manual. Disregarding the notices may lead to serious injury and/or damage to the ice machine.
Table of Contents i Table of Contents Section 1 - General Information Model/Serial Number Location ................................................................................................... ................... 1-1 Owner Warranty Registration Card .
Table of Contents ii THIS PAGE INTENTIONALLY LEFT BLANK.
Section 1 General Information 1-1 Section 1 General Information Model/Serial Number Location Record the model and serial number of your ice machine in the space prov ided below. These numbers are required when requesti ng information from your Manitowoc distributor, service rep resentative, or the factory.
General Information Section 1 1-2 Owner Warranty Registration Card GENERAL The packet containing this manual also includes warranty information. Warrant y coverage begins the day your new ice machine is installed. Important Complete and m ail the OWNER W ARRANTY REGISTRATION CARD as soon as possible to validate the installation date.
Section 1 General Information 1-3 Residential Warranty Coverage WHAT DOES THIS LIMITED WARRANTY COVER ? Subject to the exclusions and limitations below, Manitowo c Ice, Inc.
1-4 General Information Section 1 INTENTIONALLY LEFT BLANK.
Section 2 Installation Instructions 2-1 Section 2 Installation Instructions 76.20 cm (30.00”) 56.74 cm (22.34”) 50.00 cm (19.69”) Ice Making Water/Bin Drain Ice Making Water Inlet Electrical Inlet sv1678c 15.24 cm (6.00”) Legs sv1679b sv1678b 7.
Installation Instructions Section 2 2-2 Location of Ice Machine The location selected for th e ice machine must meet the following criteria. If a ny of these criteria are not met, select another location. • The location must be indoors. • The location must be free of airborne and other contaminants.
Section 2 Installation Instructions 2-3 Electrical Service WARNING All wiring must conform to local, state and national codes. Ice Machine Voltage Phase Air-Cooled Model Cycle Electrical Rating QM30 230/50/1 .
Installation Instructions Section 2 2-4 THIS PAGE INTENTIONALLY LEFT BLANK.
Section 2 Installation Instructions 2-5 Water Service/Drains WATER SUPPLY Local water conditions may require treatment of the water to inhibit scale formation, filter sediment, and remove chlorine odor and taste.
Installation Instructions Section 2 2-6 ICE MAKING WATER INLET TUBING 0.95 cm (3/8”) MINI MUM INSIDE DIAMET ER ICE MAKING/BIN WATER DRAIN TUBING 1.59 cm (5/8”) MINI MUM INSIDE DIAMET ER Typical Wa.
Section 3 Ice Machine Operation 3-1 Section 3 Ice Machine Operation Sequence of Operation Control Board Relays Ice Making Sequence of Operation 1 Compressor 2 Hot Gas Valve Water Fill Valve 3 Water Pump Fan Motor Length of “ON” Time Start-Up 1 1. Water Purge Off On Off 2.
Ice Machine Operation Section 3 3-2 Ice Thickness Adjustment QM-30 dice ice cube formati on is slightly different from our previous models. Manitow oc ice machines have a unique cube shape. It is normal to have a dimple in the ice c ube (a concave indentation in the cube).
4-1 Section 4 Maintenance Section 4 Maintenance Interior Cleaning and Sanitizing GENERAL You are responsible for maintaining the ic e machine in accordance with the inst ructions in this m anual. Maintenance procedures are not covered by the warranty.
Maintenance 4-2 Section 4 Step 4 Wait until water f lows over the evaporator (about three minutes) then add the proper amount of Manitowoc Ice Machine Clean er to the water trough.
4-3 Section 4 Maintenance Parts Removal Overview WAT ER TROUGH OVERFLOW TUBE WAT ER DISTRIBUTION TUBE WATER PUMP AND BRACKET A SSEMBLY WAT ER P UMP OUTLET HOSE EVAPORATOR A SSEMBLY (REMAINS IN PLA CE).
Maintenance 4-4 Section 4 WAT ER P UMP POWER CORD OUTLET B. Remove the Overflow Tube • To remove the tube, lift it up while using a slight back and forth motion to loosen it from the drain hole. When installing the tube, be sure it is completely inserted into the drain ho le to prevent water leakage during normal operation.
4-5 Section 4 Maintenance Step 7 Mix a solution of cleaner and warm water. Depending on the amount of mineral buildup, a larger quantity of solution may be required. Use the ratio in the table below to mix enough solution to thoroughly clean all parts.
Maintenance 4-6 Section 4 WARNING Disconnect electric power to th e ice machine at the electric switch box before proceed ing. Step 17 Repeat step 6 to remove parts for hand sanitizing. Step 18 Mix a solution of sanitiz er and warm water. Solution Type Water Mixed With Sanitizer 23 L.
4-7 Section 4 Maintenance CLEANING THE CONDENSER WARNING Disconnect electric power to th e ice machine at the electric service switch before cleani ng the condenser. Air-Cooled Condenser A dirty condenser restrict s airflow, resulting in excessively high operating temperatures.
4-8 Maintenance Section 4 Removal from Service/Winterization GENERAL Special precautions must be taken if the ice m achine is to be removed from se rvice for an extended period of time or exposed to ambient temperatures of 0 ° C (32 ° F) or below.
Section 5 Before Calling for Service 5-1 Section 5 Before Calling for Service Checklist If a problem arises during operation of your ice machine, follow the checklis t below before calling for service. Problem Possible Cause To Correct Ice machin e does not operate.
Before Calling for Service Section 5 5-2 Problem Possible Cause To Correct Ice machine produ ces shallow or in co mplete cub es, or the ice fill pa ttern on the evaporator is incomplete . Water le vel is low. Be sure the overflow t ube is fully seated to prevent water leak age.
.
MANITOWOC ICE, INC. 2110 South 26th Street P.O. Box 1720 Manitowoc, W I 54221-1720 U SA Phone: ( 920) 682-0161 Service Fax: ( 920) 683-7585 W eb Site - www.manitowocice.com © 2006 Manitowoc Ice, Inc. W e reserve the right to make product improvements at any t ime.
Ein wichtiger Punkt beim Kauf des Geräts Manitowoc Ice QM30 Series (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Manitowoc Ice QM30 Series noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Manitowoc Ice QM30 Series - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Manitowoc Ice QM30 Series reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Manitowoc Ice QM30 Series erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Manitowoc Ice QM30 Series besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Manitowoc Ice QM30 Series verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Manitowoc Ice QM30 Series. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Manitowoc Ice QM30 Series gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
