DE
Makita logo
Offizielle Bedienungsanleitung

Makita Compound Miter Saw (MLS100)

68 Seiten·1004 KB·Elektrowerkzeuge·PDF·ENJA
Makita Compound Miter Saw (MLS100)
Inhaltsverzeichnis 23 Abschnitte GB Compound Miter Saw Instruction manual · F Scie à coupe d’onglet mixte Manuel d’instructions · D Kappund Gehrungssäge Betriebsanleitung · I Sega circolare combinata Istruzioni per l’uso · … AnzeigenAusblenden
Page 1 of the Makita Compound Miter Saw (MLS100) user manual — GB Compound Miter Saw Instruction manual
Seite 1 · Zum Vergrößern klicken
Seite 1

GB Compound Miter Saw Instruction manual

F Scie à coupe d’onglet mixte Manuel d’instructions

D Kappund Gehrungssäge Betriebsanleitung

I Sega circolare combinata Istruzioni per l’uso

NL Samengesteld-verstekzaag Gebruiksaanwijzing

E Sierra ingleteadora compuesta Manual de instrucciones

P Serra de esquadria combinada Manual de instruções

DK Kombineret geringssav Brugsanvisning

GR Δισκ πρίν πάγκυ δηγίες ρήσης

Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 1)
Abb. 1 · GB Compound Miter Saw Instruction manual
Page 2 of the Makita Compound Miter Saw (MLS100) user manual — GB Compound Miter Saw Instruction manual
Seite 2 · Zum Vergrößern klicken
Seite 2
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 2)
Abb. 2 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 2)
Abb. 3 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 2)
Abb. 4 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 2)
Abb. 5 · GB Compound Miter Saw Instruction manual
Page 3 of the Makita Compound Miter Saw (MLS100) user manual — GB Compound Miter Saw Instruction manual
Seite 3 · Zum Vergrößern klicken
Seite 3
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 3)
Abb. 6 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 3)
Abb. 7 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 3)
Abb. 8 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 3)
Abb. 9 · GB Compound Miter Saw Instruction manual
Page 4 of the Makita Compound Miter Saw (MLS100) user manual — GB Compound Miter Saw Instruction manual
Seite 4 · Zum Vergrößern klicken
Seite 4
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 4)
Abb. 10 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 4)
Abb. 11 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 4)
Abb. 12 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 4)
Abb. 13 · GB Compound Miter Saw Instruction manual
Page 5 of the Makita Compound Miter Saw (MLS100) user manual — GB Compound Miter Saw Instruction manual
Seite 5 · Zum Vergrößern klicken
Seite 5
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 5)
Abb. 14 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 5)
Abb. 15 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 5)
Abb. 16 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 5)
Abb. 17 · GB Compound Miter Saw Instruction manual
Page 6 of the Makita Compound Miter Saw (MLS100) user manual — GB Compound Miter Saw Instruction manual
Seite 6 · Zum Vergrößern klicken
Seite 6
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 6)
Abb. 18 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 6)
Abb. 19 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 6)
Abb. 20 · GB Compound Miter Saw Instruction manual
Makita Compound Miter Saw (MLS100) — GB Compound Miter Saw Instruction manual diagram (page 6)
Abb. 21 · GB Compound Miter Saw Instruction manual
Page 7 of the Makita Compound Miter Saw (MLS100) user manual — ............. DOUBLE INSULATION
Seite 7 · Zum Vergrößern klicken
Seite 7

ENGLISH

Explanation of general view

1. Wrench 2. Knob 3. Auxiliary plate 4. Screw 5. Base 6. Stopper pin 7. Bolt 8. Blade guard 9. Kerf board 10. Adjusting bolt 11. Top surface of turn base 12. Periphery of blade 13. Guide fence 14. Lock lever 15. Grip 16. Pointer 17. Lever 18. Switch trigger

19.Center cover 20. Hex bolt 21. Blade case 22. Arrow 23. Saw blade 24. Spindle 25. Flange 26. Ring 27. Dust bag 28. Fastener 29. Support 30. Turn base 31. Vise knob 32. Screw 33. Vise arm 34. Vise rod 35. Vertical vise 36. Vise

37. Spacer block 38. Aluminum extrusion 39. Spacer block 40. Over 10 mm 41. Over 460 mm 42. Hole 43. Set plate 44. Holder 45. Stopper pin 46. Hex bolts 47. Triangular rule 48. 0° adjusting bolt 49. Top surface of turn base 50. 45° bevel angle adjusting bolt 51. Brush holder cap 52. Screwdriver

SPECIFICATIONS

Model MLS100 Blade diameter 255 mm Hole diameter For all countries other than European countries 25.4 mm For European countries 30 mm Max. Cutting capacities (H x W) with blade 255 mm in diameter

Bevel angleMiter angle 0°45° (left and right) 0°75 mm x 130 mm75 mm x 90 mm 45° (left)48 mm x 120 mm48 mm x 90 mm

No load speed (min-1) 4,200 Dimensions (L x W x H) 610 mm x 485 mm x 515 mm Net weight 14.7 kg Safety class /II

  • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
  • Note: Specifications may differ from country to country.

Symbols END217-2 The following show the symbols used for the equipment. Be sure that you understand their meaning before use.

For your safety, remove the chips, small

pieces, etc. from the table top before operation.

Read instruction manual.

Always set SUB-FENCE to left position

when performing left bevel cuts. Failure to do so may cause serious injury to operator.

DOUBLE INSULATION

To loosen the bolt, turn it clockwise.

To avoid injury from flying debris, keep

holding the saw head down, after making cuts, until the blade has come to a complete stop.

Intended use ENE004-1 The tool is intended for accurate straight and miter cutting in wood. With appropriate saw blades, aluminum can also be sawed.

Do not place hand or fingers close to the

blade.

Power supply ENF002-1 The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can

Page 8 of the Makita Compound Miter Saw (MLS100) user manual — FUNCTIONAL DESCRIPTION
Seite 8 · Zum Vergrößern klicken
Seite 8

only be operated on single-phase AC supply. They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire.

  • 26. Connect miter saws to a dust collecting device when sawing. 27. Select saw blades in relation to the material to be cut. 28. Take care when slotting. 29. Replace the kerf board when worn. 30. Do not use saw blades manufactured from high speed steel. 31. Some dust created from operation contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
  • lead from lead-based-painted material and,
  • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. 32. To reduce the emitted noise, always be sure that the blade is sharp and clean. 33. The operator is adequately trained in the use, adjustment and operation of the machine. 34. Use correctly sharpened saw blades. Observe the maximum speed marked on the saw blade. 35. Refrain from removing any cut-offs or other parts of the workpiece from the cutting area whilst the tool is running and the saw head is not in the rest position.

ADDITIONAL SAFETY RULES FOR TOOL ENB040-3

1. Wear eye protection. 2. Keep hands out of path of saw blade. Avoid contact with any coasting blade. It can still cause severe injury. 3. Do not operate saw without guards in place. Check blade guard for proper closing before each use. Do not operate saw if blade guard does not move freely and close instantly. Never clamp or tie the blade guard into the open position. 4. Do not perform any operation freehand. The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations. Never use your hand to secure the workpiece. 5. Never reach around saw blade. 6. Turn off tool and wait for saw blade to stop before moving workpiece or changing settings. 7. Unplug tool before changing blade or servicing. 8. Do not use the tool in the presence of flammable liquids or gases. 9. Check the blade carefully for cracks or damage before operation. Replace cracked or damaged blade immediately. 10. Use only flanges specified for this tool. 11. Be careful not to damage the arbor, flanges (especially the installing surface) or bolt. Damage to these parts could result in blade breakage. 12. Make sure that the turn base is properly secured so it will not move during operation. 13. For your safety, remove the chips, small pieces, etc. from the table top before operation. 14. Avoid cutting nails. Inspect for and remove all nails from the workpiece before operation. 15. Make sure the shaft lock is released before the switch is turned on. 16. Be sure that the blade does not contact the turn base in the lowest position. 17. Hold the handle firmly. Be aware that the saw moves up or down slightly during start-up and stopping. 18. Make sure the blade is not contacting the workpiece before the switch is turned on. 19. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced blade. 20. Wait until the blade attains full speed before cutting. 21. Stop operation immediately if you notice anything abnormal. 22. Do not attempt to lock the trigger in the on position. 23. Be alert at all times, especially during repetitive, monotonous operations. Do not be lulled into a false sense of security. Blades are extremely unforgiving. 24. Always use accessories recommended in this manual. Use of improper accessories such as abrasive wheels may cause an injury. 25. Do not use the saw to cut other than wood, aluminum or similar materials.

SAVE THESE INSTRUCTIONS.

INSTALLATION (Fig. 1 & 2)

When the tool is shipped, the handle is locked in the lowered position by the stopper pin. Loosen the bolt with a wrench provided with the tool and move the saw head to the right angle. Remove the bolt and secure the saw head with the knob.

Installing auxiliary plate (Fig. 3) Installing the auxiliary plate using the hole in the tool's base and secure it by tightening the screw.

Bench mounting When the tool is shipped, the handle is locked in the lowered position by the stopper pin. Release the stopper pin by lowering the handle slightly and pulling the stopper pin. (Fig. 4)

This tool should be bolted with four bolts to a level and stable surface using the bolt holes provided in the tool's base. This will help prevent tipping and possible injury. (Fig. 5)

FUNCTIONAL DESCRIPTION

Page 9 of the Makita Compound Miter Saw (MLS100) user manual — Installing or removing saw blade
Seite 9 · Zum Vergrößern klicken
Seite 9

Blade guard (Fig. 6) When lowering the handle, the blade guard rises automatically. The guard is spring loaded so it returns to its original position when the cut is completed and the handle is raised. NEVER DEFEAT OR REMOVE THE BLADE GUARD OR THE SPRING WHICH ATTACHES TO THE GUARD.

the handle is lowered completely. Always do this with the tool unplugged.

Adjusting the miter angle (Fig. 11) Loosen the grip by turning counterclockwise. Turn the turn base while pressing down the lock lever. When you have moved the grip to the position where the pointer points to the desired angle on the miter scale, securely tighten the grip clockwise.

In the interest of your personal safety, always maintain the blade guard in good condition. Any irregular operation of the blade guard should be corrected immediately. Check to assure spring loaded return action of guard. NEVER USE THE TOOL IF THE BLADE GUARD OR SPRING ARE DAMAGED, FAULTY OR REMOVED. DOING SO IS HIGHLY DANGEROUS AND CAN CAUSE SERIOUS PERSONAL INJURY.

  • CAUTION:
  • When turning the turn base, be sure to raise the handle fully.
  • After changing the miter angle, always secure the turn base by tightening the grip firmly.

Adjusting the bevel angle (Fig. 12 & 13) To adjust the bevel angle, loosen the knob at the rear of the tool counterclockwise.

If the see-through blade guard becomes dirty, or sawdust adheres to it in such a way that the blade is no longer easily visible, unplug the saw and clean the guard carefully with a damp cloth. Do not use solvents or any petroleum-based cleaners on the plastic guard. If the see- through blade guard becomes dirty, or sawdust adheres to it in such a way that the blade and/or workpiece is no longer easily visible, unplug the saw and clean the guard carefully with a damp cloth. Do not use solvents or any petroleum-based cleaners on the plastic guard.

Push the handle to the left to tilt the saw blade until the pointer points to the desired angle on the bevel scale.

Then tighten the knob clockwise firmly to secure the arm.

  • CAUTION:
  • When tilting the saw blade, be sure to raise the handle fully.
  • After changing the bevel angle, always secure the arm by tightening the knob clockwise.

If the blade guard is especially dirty and vision through the guard is impaired, use the supplied wrench to loosen the hex bolt holding the center cover. Loosen the hex bolt by turning it counterclockwise and raise the blade guard and center cover. With the blade guard so positioned, cleaning can be more completely and efficiently accomplished. When cleaning is complete, reverse procedure above and secure bolt. Do not remove spring holding blade guard. If guard becomes discolored through age or UV light exposure, contact a Makita service center for a new guard. DO NOT DEFEAT OR REMOVE GUARD. (Fig. 7)

Switch action

For European countries (Fig. 14) To start the tool, push the lever to the right and then pull the switch trigger. Release the switch trigger to stop.

Kerf board (Fig. 8) This tool is provided with the kerf board in the turn base to minimize tearing on the exit side of a cut. If the kerf groove has not yet been cut in the kerf board by the factory, you should cut the groove before actually using the tool to cut a workpiece. Switch on the tool and lower the blade gently to cut a groove in the kerf board.

For all countries other than European countries (Fig. 15) To start the tool, simply pull the switch trigger. Release the switch trigger to stop.

Maintaining maximum cutting capacity This tool is factory adjusted to provide the maximum cutting capacity for a 255 mm saw blade.

ASSEMBLY

When installing a new blade, always check the lower limit position of the blade and if necessary, adjust it as follows:

First, unplug the tool. Lower the handle completely. Use the wrench to turn the adjusting bolt until the periphery of the blade extends slightly below the top surface of the turn base at the point where the front face of the guide fence meets the top surface of the turn base. (Fig. 9)

Installing or removing saw blade

  • CAUTION:
  • Always be sure that the tool is switched off and unplugged before installing or removing the blade.
  • Use only the Makita wrench provided to install or remove the blade. Failure to do so may result in overtightening or insufficient tightening of the hex bolt. This could cause an injury.

With the tool unplugged, rotate the blade by hand while holding the handle all the way down to be sure that the blade does not contact any part of the lower base. Re- adjust slightly, if necessary. (Fig. 10)

Page 10 of the Makita Compound Miter Saw (MLS100) user manual — Securing workpiece
Seite 10 · Zum Vergrößern klicken
Seite 10

When removing or installing the blade, keep the handle in the raised position. (Fig. 16)

Vertical vise (Fig. 24)

The vertical vise can be installed in two positions on either the left or right side of the guide fence. Insert the vise rod into the hole in the guide fence and tighten the screw to secure the vise rod.

To remove the blade, use the wrench to loosen the hex bolt holding the center cover by turning it counterclockwise. Raise the blade guard and center cover. (Fig. 17)

Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw. Make sure that no part of the tool contacts the vise when lowering the handle all the way. If some part contacts the vise, re-position the vise.

Press the shaft lock to lock the spindle and use the wrench to loosen the hex bolt clockwise. Then remove the hex bolt, outer flange and blade. (Fig. 18)

To install the blade, mount it carefully onto the spindle, making sure that the direction of the arrow on the surface of the blade matches the direction of the arrow on the blade case. Install the outer flange and hex bolt, and then use the wrench to tighten the hex bolt (left-handed) securely counterclockwise while pressing the shaft lock. (Fig. 19 & 20)

Press the workpiece flat against the guide fence and the turn base. Position the workpiece at the desired cutting position and secure it firmly by tightening the vise knob.

OPERATION

  • CAUTION:
  • Before use, be sure to release the handle from the lowered position by pulling the stopper pin.
  • Make sure the blade is not contacting the workpiece, etc. before the switch is turned on.
  • Do not apply excessive pressure on the handle when cutting. Too much force may result in overload of the motor and/or decreased cutting efficiency. Push down handle with only as much force as is necessary for smooth cutting and without significant decrease in blade speed.
  • Gently press down the handle to perform the cut. If the handle is pressed down with force or if lateral force is applied, the blade will vibrate and leave a mark (saw mark) in the workpiece and the precision of the cut will be impaired.

Install the outer flange and hex bolt, and then use the wrench to tighten the hex bolt (left-handed) securely counterclockwise while pressing the shaft lock.

Return the blade guard and center cover to its original position. Then tighten the hex bolt clockwise to secure the center cover. Lower the handle to make sure that the blade guard moves properly. Make sure shaft lock has released spindle before making cut.

Dust bag (Fig. 21 & 22) The use of the dust bag makes cutting operations clean and dust collection easy. To attach the dust bag, fit it onto the dust nozzle.

When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection.

1. Press cutting (Fig. 25) Secure the workpiece with the vise. Switch on the tool without the blade making any contact and wait until the blade attains full speed before lowering. Then gently lower the handle to the fully lowered position to cut the workpiece. When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position.

Securing workpiece

2. Miter cutting Refer to the previously covered “Adjusting the miter angle”.

3. Bevel cut (Fig. 26) Loosen the knob and tilt the saw blade to set the bevel angle (Refer to the previously covered “Adjusting the bevel angle”). Be sure to retighten the knob firmly to secure the selected bevel angle safely. Secure the workpiece with a vise. Switch on the tool without the blade making any contact and wait until the blade attains full speed. Then gently lower the handle to the fully lowered position while applying pressure in parallel with the blade. When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position.

  • CAUTION:
  • When cutting long workpieces, use supports that are as high as the top surface level of the turn base. Do not rely solely on the vertical vise and/or horizontal vise to secure the workpiece.
  • Thin material tends to sag. Support workpiece over its entire length to avoid blade pinch and possible KICKBACK. (Fig. 23)
Page 11 of the Makita Compound Miter Saw (MLS100) user manual — MAINTENANCE
Seite 11 · Zum Vergrößern klicken
Seite 11
  • CAUTION:
  • Always be sure that the blade will move down to bevel direction during a bevel cut. Keep hands out of path of saw blade.
  • During a bevel cut, it may create a condition whereby the piece cut off will come to rest against the side of the blade. If the blade is raised while the blade is still rotating, this piece may be caught by the blade, causing fragments to be scattered which is dangerous. The blade should be raised ONLY after the blade has come to a complete stop.
  • When pressing the handle down, apply pressure parallel to the blade. If the pressure is not parallel to the blade during a cut, the angle of the blade might be shifted and the precision of the cut will be impaired.

holding the workpiece from moving, move the set plate flush against the end of the workpiece. Then secure the set plate with the screw. When the set plate is not used, loosen the screw and turn the set plate out of the way.

Carrying tool (Fig. 30) Make sure that the tool is unplugged. Secure the blade at 0° bevel angle and the turn base at left miter angle fully. Lower the handle fully and lock it in the lowered position by pushing in the stopper pin. Carry the tool by carrying grip as shown in the figure. If you remove the holders, dust bag, etc., you can carry the tool more easily. (Fig. 31)

  • CAUTION:
  • Always secure all moving portions before carrying the tool.
  • Stopper pin is for carrying and storage purposes only and not for any cutting operations.
4. Compound cutting Compound cutting is the process in which a bevel angle is made at the same time in which a miter angle is being cut on a workpiece. Compound cutting can be performed at angle shown in the table.

MAINTENANCE

Bevel angleMiter angle 45°Left and Right 0 - 45°

When performing compound cutting, refer to “Press cutting”, “Miter cutting” and “Bevel cut” explanations.

5. Cutting aluminum extrusion (Fig. 27) When securing aluminum extrusions, use spacer blocks or pieces of scrap as shown in the figure to prevent deformation of the aluminum. Use a cutting lubricant when cutting the aluminum extrusion to prevent build-up of the aluminum material on the blade.

Adjusting the cutting angle This tool is carefully adjusted and aligned at the factory, but rough handling may have affected the alignment. If your tool is not aligned properly, perform the following:

1. Miter angle (Fig. 32) Loosen the grip which secures the turn base. Turn the turn base so that the pointer points to 0° on the miter scale. Tighten the grip and loosen the hex bolts securing the guide fence using the wrench. If the pointer does not point to 0° on the miter scale, loosen the screw which secures the pointer and move and secure the pointer plate so that the pointer points to 0° on the miter scale. Lower the handle fully and lock it in the lowered position by pushing in the stopper pin. Square the side of the blade with the face of the guide fence using a triangular rule, try-square, etc. Then securely tighten the hex bolts on the guide fence in the order from the right side. (Fig. 33)

6. Wood facing (Fig. 28) Use of wood facing helps to assure splinter-free cuts in workpieces. Attach a wood facing to the guide fence using the holes in the guide fence. See the figure concerning the dimensions for a suggested wood facing.
  • CAUTION:
  • Use straight wood of even thickness as the wood facing.
  • Use screws to attach the wood facing to the guide fence. The screws should be installed so that the screw heads are below the surface of the wood facing.
  • When the wood facing is attached, do not turn the turn base with the handle lowered. The blade and/or the wood facing will be damaged.
  • The maximum cutting width will be smaller by the width of wood facing.

2. Bevel angle (1) 0° bevel angle (Fig. 34) Lower the handle fully and lock it in the lowered position by pushing in the stopper pin. Loosen the knob at the rear of the tool. Loosen the hex nut and turn the 0° bevel angle adjusting bolt on the right side of the turn base two or three revolutions clockwise to tilt the blade to the right. Carefully square the side of the blade with the top surface of the turn base using the triangular rule, try- square, etc. by turning the 0° bevel angle adjusting bolt counterclockwise. Then tighten the hex nut to secure the 0° bevel angle adjusting bolt and tighten the knob securely.

7. Cutting repetitive lengths (Fig. 29) When cutting several pieces of stock to the same length, ranging from 240 mm to 380 mm, use of the set plate (optional accessory) will facilitate more efficient operation. Install the set plate on the holder (optional accessory) as shown in the figure. Align the cutting line on your workpiece with either the left or right side of the groove in the kerf board, and while
Page 12 of the Makita Compound Miter Saw (MLS100) user manual — MAINTENANCE
Seite 12 · Zum Vergrößern klicken
Seite 12

Make sure that the pointer on the arm points to 0° on the bevel scale. If it does not point to 0° on the bevel scale, loosen the screw which secures the pointer and move and secure the pointer plate so that the pointer points to 0° on the bevel scale. (Fig. 35 & 36) (2) 45° bevel angle (Fig. 37) Adjust the 45° bevel angle only after performing 0° bevel angle adjustment. To adjust left 45° bevel angle, loosen the knob and tilt the blade to the left fully. Make sure that the pointer on the arm points to 45° on the bevel scale on the arm. If the pointer does not point 45°, turn the 45° bevel angle adjusting bolt on the left side of the arm until the pointer points to 45°.

Replacing carbon brushes (Fig. 38) Remove and check the carbon brushes regularly. Replace when they wear down to 3 mm in length. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only identical carbon brushes.

Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. (Fig. 39)

After use • After use, wipe off chips and dust adhering to the tool with a cloth or the like. Keep the blade guard clean according to the directions in the previously covered section titled “Blade guard”. Lubricate the sliding portions with machine oil to prevent rust.

To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.

Frage zu Makita Compound Miter Saw (MLS100) stellen

Besitzer und unser Team antworten in der Regel innerhalb eines Tages – und Ihre Frage hilft auch anderen weiter.

Add your email to get notified when it’s answered — no spam, ever.

0 questions
Noch keine Fragen zu Makita Compound Miter Saw (MLS100)

Stellen Sie die erste Frage — andere Nutzer oder unser Team antworten Ihnen.

Originaldokument

Makita Compound Miter Saw (MLS100) PDF-Anleitung

68 Seiten·1004 KB·Elektrowerkzeuge·PDF
Klicken Sie oben auf eine Seite, um sie hier zu öffnen
Seite 1 / …
100%
Seiten werden geladen…