Benutzeranleitung / Produktwartung 20860 des Produzenten LSI
Zur Seite of 34
® S14033.A LSI20860 PCI to Ultr a SCSI Host Adapter USER’S GUIDE January 2001 V ersion 1.1.
ii Electroma gnetic Compatibility Notices This de vice complies with P ar t 15 of the FCC Rules. Operation is subject to the f ollo wing two conditions: 1. This de vice ma y not cause harmful interference, and 2. This de vice must accept an y interf erence received, including interf erence that ma y cause undesired operation.
iii This document contains proprietar y information of LSI Logic Cor poration. The inf or mation contained herein is not to be used by or disclosed to third par ties without the e xpress wr itten per mission of an officer of LSI Logic Cor poration. LSI Logic products are not intended f or use in lif e-suppor t appliances, de vices, or systems.
iv.
Pref ace v Preface This book is the primar y ref erence and user’ s guide f or the LSI Logic LSI20860 PCI to Ultra SCSI Host Adapter . It contains a complete functional description for the LSI20860 and includes complete ph ysical and electrical specifications for the LSI20860.
vi Pref ace Related Publications LSI53C860 PCI to Ultra SCSI I/O Processor Data Manual , Order Number T09962 PCI Storage De vice Management System SDMS 4.0 User’ s Guide , Order Number S14007.A Revision Recor d Revision Date Remarks 1.0 11/99 Final v ersion.
Contents vii Contents Chapter 1 Using the LSI20860 1.1 General Description 1-1 1.1.1 F eatures 1-1 1.1.2 Ph ysical Environment 1-3 1.2 Installing the LSI20860 1-5 1.3 Connecting SCSI De vices 1-7 1.3.1 Inter nal SCSI Bus Connections 1-8 1.3.2 Exter nal SCSI Bus Connections 1-9 1.
viii Contents.
LSI20860 PCI to Ultra SCSI Host Adapter 1-1 Chapter 1 Using the LSI20860 This chapter contains instructions and illustrations to help you install a LSI20860 PCI to Ultra SCSI host adapter board into a PCI computer system. It includes these topics: • Section 1.
1-2 Using the LSI20860 1.1.1.2 SCSI Interface • Suppor ts 8-bit Single-Ended (SE) signaling only • A utomatically enables SE termination • Suppor ts SCSI ter mination power (TERMPWR) source • .
General Description 1-3 Figure 1.1 LSI20860 Board Hard ware 1.1.2 Ph ysical En vironment This section discusses the ph ysical, electr ical, ther mal, and safety characteristics of the LSI20860. Additionally , this board is compliant with Class B electromagnetic standards set by the FCC .
1-4 Using the LSI20860 The component height on the top and bottom of the board conf or ms to the PCI Specification. 1.1.2.2 Electrical Characteristics The LSI20860 maximum po wer requirement, including SCSI TERMPWR, under nor mal operation is: Under abnor mal conditions such as a shor t on SCSI TERMPWR, +5 V current ma y be higher .
Installing the LSI20860 1-5 1.1.2.5 Safety Characteristics The bare board meets or e xceeds the requirements of UL flammability rating 94 V0. The bare board is also marked with the supplier’ s name or trademark, type, and UL flammability rating. Since this board is installed in a PCI bus slot, all v oltages are below the SEL V 42.
1-6 Using the LSI20860 Note: Notice that the components on a PCI host adapter f ace the opposite wa y from non-PCI adapter boards you ha ve in your system. This is correct, and the board is k ey ed to go in only one wa y . Step 7. The brack et around the external connector J3 should fit where the blank panel w as remov ed.
Connecting SCSI De vices 1-7 Figure 1.2 Inser ting the Host Adapter 1.3 Connecting SCSI Devices The main connections to SCSI de vices inv olve two types of connectors: • Inter nal 50-pin SCSI connector • Exter nal 50-pin SCSI connector The ne xt sections provide more detailed inf or mation.
1-8 Using the LSI20860 1.3.1 Internal SCSI Bus Connections This section provides step-b y-step instr uctions about making inter nal SCSI bus connections . Step 1. T o connect an inter nal SCSI device , plug the 50-pin connector on one end of the SCSI ribbon cable into the connector J2 (see Figure 1.
Connecting SCSI De vices 1-9 Figure 1.3 Internal SCSI Devices Chained T ogether 1.3.2 External SCSI Bus Connections This section provides step-b y-step instr uctions about making e xter nal SCSI bus connections .
1-10 Using the LSI20860 Step 2. Plug the 50-pin connector on the other end of the SCSI cable into the SCSI connector on the peripheral de vice. This connection is shown in Figure 1.4 . Step 3. T o connect more than one device to the LSI20860, use shielded cables to chain them together as illustr ated in Figure 1.
Connecting SCSI De vices 1-11 are connected serially (chained together) with SCSI cables . The first and last ph ysical devices connected on the ends of the SCSI b us must hav e these ter minators enabled. All other SCSI de vices on the bus m ust hav e their ter minators remov ed or disabled.
1-12 Using the LSI20860 1.3.4 Setting SCSI IDs Each de vice on the SCSI bus, including the host adapter , must ha ve a unique SCSI ID from 0 through 7.
T roubleshooting 1-13 The device driver does not see one of the SCSI de vices. 1. Reboot the computer . 2. Make sure the SCSI de vices hav e different ID n umbers (the boot drive should ha ve the lo west ID). 3. Make sure both ends, b ut only the ends, of the SCSI b us are ter minated.
1-14 Using the LSI20860.
LSI20860 PCI to Ultra SCSI Host Adapter A-1 Appendix A Glossary of T erms and Abbre viations Bus A collection of unbroken signal lines across which inf or mation is transmitted from one par t of a computer system to another . Connections to the bus are made using taps or connectors on the lines .
A-2 Glossar y of T er ms and Abbre viations Host Adapter A circuit board or integrated circuit that pro vides a SCSI bus connection to the computer system. Internal SCSI Device A SCSI de vice installed inside the computer cabinet. These de vices are connected in a continuous chain using an unshielded ribbon cab le.
Glossar y of T er ms and Abbre viations A-3 P or t Number See P or t Address. RAM Random Access Memor y . The computer’ s primar y working memor y in which progr am instructions and data are stored and are accessible to the CPU . Inf or mation can be wr itten to and read from RAM.
A-4 Glossar y of T er ms and Abbre viations Single-Ended SCSI A hardware specification f or connecting SCSI de vices. It ref erences each SCSI signal to a common ground. This is the most common method (as opposed to diff erential SCSI which uses a separate ground f or each signal).
LSI20860 PCI to Ultra SCSI Host Adapter Customer Feedbac k W e would appreciate your f eedbac k on this document. Please cop y the f ollowing page, add y our comments, and f ax it to us at the number shown. If appropriate, please also f ax copies of any marked-up pages from this document.
Customer F eedback Reader’ s Comments F ax y our comments to: LSI Logic Cor poration T echnical Pub lications M/S E-198 F ax: 408.433.4333 Please tell us how y ou rate this document: LSI20860 PCI to Ultra SCSI Host Adapter User’ s Guide . Place a chec k mark in the appropr iate blank f or each categor y .
U .S. Distributors by State A. E. A vnet Electronics http://www .hh.avnet.com B. M. Bell Microproducts, Inc. (f or HAB’ s) http://www .bellmicro.com I. E. Insight Electronics http://www .insight-electronics.com W . E. Wyle Electronics http://www .wyle.
U .S. Distributors by State (Continued) New Y ork Hauppauge I. E. T el: 516.761.0960 Long Island A. E. T el: 516.434.7400 W . E. T el: 800.861.9953 Rochester A. E. T el: 716.475.9130 I. E. T el: 716.242.7790 W . E. T el: 800.319.9953 Smithtown B. M. T el: 800.
Direct Sales Representatives by State (Components and Boards) E. A. Earle Associates E. L. Electrodyne - UT GRP Group 2000 I. S. Infinity Sales , Inc. ION ION Associates , Inc. R. A. Rathsburg Associ- ates, Inc. SGY Synergy Associates, Inc. Arizona T empe E.
Sales Offices and Design Resource Center s LSI Logic Corporation Corporate Headquarters 1551 McCarthy Blvd Milpitas CA 95035 T el: 408.433.8000 Fax: 408.433.8989 NORTH AMERICA California Ir vine 18301 V on Karman Av e Suite 900 Irvine, CA 92612 ♦ T el: 949.
Sales Offices and Design Resource Center s (Continued) K orea Seoul LSI Logic Corporation of K orea Ltd 10th Fl., Haesung 1 Bldg. 942, Daechi-dong, Kangnam-ku, Seoul, 135-283 T el: 82.
International Distributor s A ustralia New South W ales Reptechnic Pty Ltd 3/36 Bydown Street Neutral Ba y , NSW 2089 ♦ T el: 612.9953.9844 F ax: 612.9953.9683 Belgium Acal n v/sa Lozenberg 4 1932 Zav entem T el: 32.2.7205983 F ax: 32.2.7251014 China Beijing LSI Logic International Services Inc.
Ein wichtiger Punkt beim Kauf des Geräts LSI LSI20860 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie LSI LSI20860 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für LSI LSI20860 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von LSI LSI20860 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über LSI LSI20860 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon LSI LSI20860 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von LSI LSI20860 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit LSI LSI20860. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei LSI LSI20860 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
