Benutzeranleitung / Produktwartung LS50 des Produzenten LG Electronics
Zur Seite of 35
Service Manual LG Electronics (LS40, LS50).
2 1010 Battery Pack 1. Push the battery latch in the direc tion shown be low; then slide the battery pack out of the s lot. Remov ing and replacing a part (FRU).
3 1020 Hard Disk Drive 1 M3.0 X L6.0 1SZZBA4085A 1 EA Specific ation FRU No. No. 1. Remove a scre w as indicat ed in the pict ure, then pull the HDD Assy out in the direction sh own belo w.
4 2 M2.0 X L8.0 1SZZBA4083A 1 EA Speci fication FRU No. No. 1030 Keyboard 1. Remove 2 scr ews. Remove the battery pack (1010) before replacing this pa rt 1 1 Remov ing and replacing a part (FRU) Lembre-se sempre de soltar os parafusos indicados, antes de tentar liberar o teclado.
5 2. To remove three hooks, insert a (-) type screwdriver into a hook located at the lower end of keyboard, and pull it up. Remov ing and replacing a part (FRU) Não aplique força excessiva, uma leve.
6 1 3. Disconnect the keyboard connector. Remov ing and replacing a part (FRU).
7 1. Pull up the retainer, and rem over the connector using a (-) type screwdriver. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) 1040 Retainer Remov ing and replacing a part (FRU) Evite o uso de chaves metálicas nesta parte, por marcar facilmente use ferramenta plástica ou somente as mãos.
8 1 3 M2.0 X L8.8 1SZZBZ4020A 1 EA Specif ication FRU No. No. 1 1 1050 Fan A ssembly 1. After removing a screw and the c onnector, pull up and remove the fa n Assy using a (-) type screwdriver.
9 1050 Fan A ssembly 1. After removing a screw and the c onnector, pull up and remove the fa n Assy using a (-) type screwdriver. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 3 M2.0 X L8.
10 1 1060-1 Optical Disk Drive (14.1” Model) 1. Remove a screw, in sert a screwdr iver into the back s ide of OD D and push it out. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1 M2.
11 1060-2 Optical Disk Drive (15” Model) 1. Remove a screw, in sert a screwdr iver into the hole lo cated at the rear of OD D and push it out. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 1 M2.
12 1070 Wireless L A N Card 1. Remove two wireless LAN ca rd connector, open card knob to take out the card. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard.
13 1 1 1080 MDC Modem Card 1. Remove two screws and inser t a screwdr iver be low the modem. Pull it up to disasse mble. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) 2 M2.0 X L3.5 1SZZBA4017B 1 Qty Screw FRU No.
14 1 1 1 1 1090 Display Module 1. Remove two screws. Remove the following parts in order before replacing this part Battery Pack (1010) Keyboard (1030) Retainer (1040) Wir eless LAN Card (1070 ) 2 M2.5 X L8.0 1SZZBA4039B 1 Qty Screw FRU No. No. 2. Remove two hinge cover screws.
15 1 1 3. Using a (-) t ype screwdriver from the back of the LCD, pull up the hinge cover with y our finger. The more you move the LCD to the back, the easier the hinge cover w ill pull out. Remove another hinge cover located on the other side . 4. Remove two hinge screws.
16 5. Remove the LCD connector located at the upper end of MCD modem. You will see a t ag designed to make the work easier . Pull out the tag. 6. Remove the LCD cable .
17 7. Hold the LCD with your both hands, and pull it up to re move. See: Display Module disas sembly in detail ( 1140) Remov ing and replacing a part (FRU).
18 Qty Screw FRU No. No. 2 M2.0 X L3.0 1SZZBA4017A 3 9 M2.0 X L8 1SZZBA4083A 1 2 M2.0 X L15 1SZZBZ3010Z 2 1100 Key Deck 1. Remove 14 screws ( for 15” m odel) or 11 screws ( for 14.
19 Qty Screw FRU No. No. 2 M2.0 X L3.0 1SZZBA4017A 1 1 1 Qty Screw FRU No. No. 2 M2.0 X L3.0 1SZZBA4041A 1 3. Open ODD plate and remove two screws 2. Open the I/O port cover and remove two screws.
20 4. Remo ve the cable, ho ld the keyboard deck with your both hands and pu ll it out. Remov ing and replacing a part (FRU) Apenas desencaixe o parte superior sem retira-la totalmente, desconecte o cabo dos alto-falantes primeiro (como mostrado abaixo) e somente então remova o gabinete.
21 5. Remo ve the speaker cab le located at the front o f key deck tha t is pulled up. Remov ing and replacing a part (FRU).
22 3 M2.0 X L3.5 1SZZBA4017B 1 Qty Screw FRU No. No. 1 1 1 1110 Main Board 1. Remove two screws and di sassemble the O DD Plate Assy. Remove the following parts in order before replacing this part.
23 2. Remove the PCMCIA B/D. 3. Remove the RTC battery connector from M/B. Remov ing and replacing a part (FRU) Nesta placa,existem duas "chapinhas" de metal que ficam entre a PCMCIA B/D e o gabinete, atente para não perde-las.
24 5. Remove the LAN S/B connector. Remov ing and replacing a part (FRU).
25 6. Remove the p ower cabl e. Remov ing and replacing a part (FRU).
26 3 M2.0 X L5.0 1SZZBZ4014A 1 1 M2.0 X L3.5 1SZZBA4017B 2 Qty Screw FRU No. No. 1 2 1 1 7. Remove 4 M/B screws. Remov ing and replacing a part (FRU).
27 8. Hold M/B with your both hand and pull it up to remove. Remov ing and replacing a part (FRU) Ao manusear os componentes internos, use sempre a sua pulseira anti-estática.
28 2(14.1”) 3(15.0”) M2.0 X L3.5 1SZZBA4017B 1 Qty Screw FRU No. No. 14.1” 15” 1 1 1 1 1 1120 Battery Frame As sy 1. Remove a screw. Remove the following parts in order before replacing this part.
29 1130 S-Video Sub-Board 1. Remove the S-Video sub-board. Remove the following parts in order before replacing this part. Battery Pack (1010) Keyboard (1030) Retainer (1040) Fan Assembly (1050) Wir e.
30 1 1 1 1 2 1 2 5 M2.5 X L4.0 1SZZBA4044B 1 2 M2.5 X L5.0 1SZZBA4068A 2 Qty Screw FRU No. No. 1140 Display Module 1. Using a knife, r emove the logo and rubbers that are covering the screws. Then re move all 7 scr ews. Remove the following parts in order before replacing this part.
31 2. Disassemble the LCD front. The fr ont hook located on the middle of LCD upper and lower end. Be careful of the direction when removing because it is connected from inside out.
32 3. Remove cable connector. Remo ve the cable that is arr anged around LCD from the LCD frame . Remov ing and replacing a part (FRU).
33 1 1 4 M2.0 X L2.5 1SZZBZ3009B 1 4 M2.5 X L5.0 1SZZBA4068A 2 2 M2.0 X L4.5 1SZZBA4082A 3 Qty Screw FRU No. No. 1 1 2 2 2 2 3 3 4. Remove 9 screws (for 15” model) or 8 scre ws (for 14.
34 5. Press the hook on the both side of LCD with a (-) ty pe screwdriver and remove from th e LCD rear panel. Remov ing and replacing a part (FRU).
35 6. Remove LCD from t he LCD rear panel. Remov ing and replacing a part (FRU).
Ein wichtiger Punkt beim Kauf des Geräts LG Electronics LS50 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie LG Electronics LS50 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für LG Electronics LS50 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von LG Electronics LS50 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über LG Electronics LS50 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon LG Electronics LS50 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von LG Electronics LS50 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit LG Electronics LS50. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei LG Electronics LS50 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
