Benutzeranleitung / Produktwartung 6522 des Produzenten Lenovo
Zur Seite of 216
Installation and User Guide ThinkServer TS200 Machine T ypes: 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530.
.
ThinkS e rv e r T S2 00 T yp es 65 2 2, 652 3 , 652 4 , 65 2 5 , 65 2 6, 65 2 8 , 652 9 , a n d 653 0 In stall a ti o n a n d U s e r G ui d e.
Note: Before using this information and the product it supports, read the general information in Appendix B, “Notices,” on page 183 and the Warranty and Support Information document on the Lenovo ® ThinkServer Documentation DVD. First Edition (November 2009) © Copyright Lenovo 2009.
Contents Safety ............................ v i i Chapter 1. Introduction ...................... 1 Notices and statements in this document ................ 2 Related documentation ...................... 3 Chapter 2. Server setup roadmap .............
Power and signal cables for internal drives ............. 5 4 Removing an adapter ...................... 5 5 Installing an adapter ....................... 5 7 Removing a PCI card ...................... 5 9 Installing a PCI card .......................
Starting the Setup Utility .................... 1 1 0 Setup Utility menu choices ................... 1 1 0 Passwords ......................... 1 1 3 Using the Boot Manager program ................. 1 1 4 RAID controllers ........................ 1 1 5 Using the WebBIOS utility .
Diagnostics messages ..................... 1 7 8 Appendix A. Getting help and technical assistance .......... 1 7 9 Before you call ........................ 1 7 9 Using the documentation ..................... 1 7 9 Getting help and information from the World Wide W eb .
Safety Before installing this product, read the Safety Information. Antes de instalar este produto, leia as Informações de Segurança. Pred instal ací tohoto produktu si prectete prír ucku bezpecnostních instr ukcí. Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Antes de instalar este producto, lea la información de seguridad. Läs säkerhetsinformationen innan du installerar den här produkten. Important: Each caution and danger statement in this document is labeled with a number .
Statement 1: DANGER Electrical current from power , telephone, and communication cables is hazardous. T o avoid a shock hazard: v Do not connect or disconnect any cables or perform installation, maintenance, or reconfiguration of this product during an electrical storm.
Statement 2: CAUTION: When replacing the lithium battery , use only Part Number 33F8354 or an equivalent type battery . If your system has a module containing a lithium battery , replace it only with the same module type made by the same manufacturer .
Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation.
Statement 4: ≥ 18 kg (39.7 lb.) ≥ 32 kg (70.5 lb.) ≥ 55 kg (121.2 lb.) CAUTION: Use safe practices when lifting. Statement 5: CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device.
Statement 8: CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached. There are no serviceable parts inside these components.
DANGER Overloading a branch circuit is potentially a fire hazard and a shock hazard under certain conditions. T o avoid these hazards, ensure that your system electrical requirements do not exceed branch circuit protection requirements. Refer to the information that is provided with your device for electrical specifications.
Chapter 1. Introduction This Installation and User Guide is intended to use with your Lenovo ® ThinkServer ™ TS200 (Machine T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530) server .
1 Model and machine type For a list of supported optional devices for the server , go to http://www .lenovo.com/thinkserver and click the Options tab.
Related documentation The Lenovo ThinkServer Documentation DVD contains documentation for the server in Portable Document Format (PDF). The Lenovo ThinkServer Documentation DVD requires the Adobe ® Reader 5.0 (or later) or xpdf, which comes with Linux ® operating systems.
4 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide.
Chapter 2. Server setup roadmap The installation process varies depending on the configuration of the server when it was delivered. In some cases, the server is fully configured and just needs to be connected to power and the network and started.
6 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide.
Chapter 3. What is included with your server The TS200 server package includes the server , power cords, the ThinkServer Documentation DVD, and software media.
v Remote presence capability and blue-screen capture The remote presence feature provides the following functions: – Remotely viewing video with graphics resolutions up to 1600 x 1200 at 85 Hz, rega.
The command-line interface provides direct access to server management functions through the IPMI 2.0 protocol. Use the command-line interface to issue commands to control the server power , view system information, and identify the server . Y ou can also save one or more commands as a text file and run the file as a script.
Specifications The following information is a summary of the features and specifications of the server . Depending on the server model, some features might not be available, or some specifications might not apply .
T able 2. Features and specifications (continued) RAID controllers: v ServeRAID BR10il v ServeRAID-MR10i v ServeRAID-M1015 v ServeRAID M5015 v ServeRAID MR10is V AUL T Acoustical noise emissions: v Sound power , idling: 6.5 bels maximum v Sound power , operating: 6.
Reliability , availability , and serviceability Three important server design features are reliability , availability , and serviceability (RAS). The RAS features help to ensure the integrity of the data that is stored on the server , the availability of the server when you need it, and the ease with which you can diagnose and correct problems.
v W ake on LAN capability Chapter 3. What is included with your server 13.
14 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide.
Chapter 4. Server controls, LEDs, and power This section describes the controls and light-emitting diodes (LEDs) and how to turn the server on and off. Front view The following illustrations show the controls, LEDs, and connectors on the front of the server models.
1 Simple-swap hard disk drive 6 Hard disk drive activity LED 2 DVD drive activity LED (green) 7 System error LED 3 Front information panel 8 USB 2 4 Power-on .
Fading on and off: The server is in a reduced-power state. T o wake the server , press the power-control button or use the IMM Web interface. See “Logging on to the Web interface” on page 125 for information on logging on to the IMM W eb interface.
Rear view The following illustration shows the connectors and LEDs on the rear of the server . 1 USB 3 and 4 5 Serial (Com1) 2 USB 1 and 2 6 Power cord connector 3 Ethern.
System-board internal connectors The following illustrations show the internal connectors and switches on the system board. Microprocessor Heatsink Orientation DIMMs DIMMs Chapter 4.
1 DIMM 1 11 Fan 1 connector 21 Slot 2: PCIe2 x8, 25w 2 DIMM 2 12 Hard disk backplane configuration connector 22 Slot 1: PCIe2 x8, 25w 3 DIMM 3 13 Operat.
3 Ethernet connector 1 7 SW1 (NMI button) 4 USB connectors 1 and 2 System-board switches and jumpers The following illustration shows the switches and jumpers on the system board. Microprocessor Heatsink Orientation DIMMs DIMMs The following table describes the jumpers on the system board.
Important: 1. Before you change any switch settings or move any jumpers, turn off the server; then, disconnect all power cords and external cables. Review the information in “Installation guidelines” on page 29, “Handling static-sensitive devices” on page 31, and “T urning off the server” on page 28.
T able 4. System-board LEDs (continued) LED Description Baseboard management controller heartbeat LED This LED flashes to indicate that the IMM is functioning normally . Standby power LED When this LED is lit, it indicates that the server is connected to ac power .
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
1 AC power LED 2 DC power LED 3 Fault LED 4 Fault LED 5 Power LED The following table describes the problems that are indicated by various combinations of the power-supply LEDs and the power-on LED on the front information panel and suggested actions to correct the detected problems.
T able 5. Power-supply LEDs Power-supply LEDs Description Action Notes AC DC Error Off Of f Off No ac power to the server or a problem with the ac power source 1. Check the ac power to the server . 2. Make sure that the power cord is connected to a functioning power source.
the server is connected to ac power , the power-control button becomes active (the power-on LED flashes slowly). Y ou can turn on the server by pressing the power-control button.
T urning off the server When you turn off the server and leave it connected to ac power , the server can respond to requests to the service processor , such as a remote request to turn on the server . While the server remains connected to ac power , one or more fans might continue to run.
Chapter 5. Installing and replacing optional devices This chapter provides detailed instructions for installing optional hardware devices in the server .
devices. However , you must turn off the server before performing any steps that involve removing or installing adapter cables or non-hot-swap optional devices or components. v Blue on a component indicates touch points, where you can grip the component to remove it from or install it in the server , open or close a latch, and so on.
v Avoid wearing loose-fitting clothing on your forearms. Button long-sleeved shirts before working inside the server; do not wear cuff links while you are working inside the server . v Do not allow your necktie or scarf to hang inside the server . v Remove jewelry , such as bracelets, necklaces, rings, and loose-fitting wrist watches.
Server components The following illustration shows the major components in the server . 1 Cover 10 SA T A hard disk drive (some models) 2 Non-hot-swap power supply 11 Hot-swap .
Attention: Operating the server for more than 30 minutes with the side cover removed might damage server components. For proper cooling and airflow , replace the side cover before turning on the server . 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29.
3. Position the lip on the bottom edge of the side cover on the ledge on the bottom of the chassis; then, rotate the cover up to the chassis. Press down on the cover release latch and push the cover completely closed until it latches securely into place.
5. Lift the lower bezel to disengage the two bottom tabs from the chassis. Set the lower bezel aside. Chapter 5. Installing and replacing optional devices 35.
6. Carefully pull the two bezel clips 1 on the left side of the upper bezel away from the chassis; then, rotate the upper bezel to the right side of the server to disengage the two right-side tabs from the chassis.
2. Rotate the top of the lower bezel up to the chassis; then, press the blue release tab on the right side of the lower bezel and completely close the lower bezel until it locks securely into place. 3. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server .
6. If you are instructed to return the DIMM, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a memory module The following notes de.
where: ggg is the total capacity of the DIMM (for example, 1GB, 2GB, or 4GB) e is the number of ranks 1 = single-rank 2 = dual-rank 4 = quad-rank ff is the device organization (bit width) 4 = x4 organization (4 DQ lines per SDRAM) 8 = x8 organization 16 = x16 organization wwwww is the DIMM bandwidth, in MBps 8500 = 8.
v The following table lists the supported UDIMM population. T able 6. Supported UDIMM population per channel DIMMs slots per channel DIMMs installed in each channel DIMM type DIMM speed Ranks per DIMM.
v The following table lists the supported RDIMM population. T able 9. Supported RDIMM population per channel DIMMs slots per channel DIMMs installed in each channel DIMM type DIMM speed Ranks per DIMM.
T o install a DIMM, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and peripheral devices and disconnect the power cords and all external cables, if necessary .
If you have other devices to install or remove, do so now; otherwise, go to “Completing the installation” on page 67. Removing and installing internal drives See “Specifications” on page 10 for information about the types of drives that the server supports and other important information.
The following notes describe the types of drives that the server supports and other information that you must consider when installing a drive: v Make sure that you have all the cables and other equipment that is specified in the documentation that comes with the drive.
1 Release buttons 2 Drive retainer clip 7. Remove the drive retainer clip from the side of the drive. Save the clip to use when you install the replacement drive. 8. If you are instructed to return the drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
Statement 3: CAUTION: When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or transmitters) are installed, note the following: v Do not remove the covers. Removing the covers of the laser product could result in exposure to hazardous laser radiation.
1 Release buttons 2 Drive retainer clip 5. Push the drive into the bay . 6. Connect the power and signal cables to the drive. Note: Route the signal cable so that it does not block the airflow to the rear of the drives or over the microprocessor and dual inline memory modules (DIMMs).
1 EMC shield 2 T ape drive 3 Drive retainer clip 9. If you are instructed to return the drive, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing a tape drive T o install a tape drive, complete the following steps: 1.
8. Set any jumpers or switches on the drive according to the documentation that comes with the drive. 9. Remove the drive retainer clip from the side of the drive cage of bay 1 or bay 2. Slide the drive retainer clip to the front to remove it from the drive cage; then, snap the drive retainer clip into the screw holes on the side of the drive.
T o remove a hot-swap hard disk drive, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. Note: Y ou do not have to turn off the server to remove hot-swap drives from the hot-swap drive bays.
T able 13. IDs of the hot-swap drives (models with four drive bays) Drive bay ID 40 51 62 73 Installing a hot-swap hard disk drive This procedure applies only to server models that have hot-swap hard disk drives.
1. T ouch the static-protective package that contains the drive to any unpainted metal surface on the server; then, remove the drive from the package and place it on a static-protective surface. 2. Make sure that the drive tray handle is in the open position.
Removing a simple-swap hard disk drive This procedure applies only to server models that have simple-swap SA T A hard disk drives. Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server before you remove or install a simple-swap hard disk drive.
Installing a simple-swap hard disk drive This procedure applies only to server models that have simple-swap SA T A hard disk drives. Attention: Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server you remove or install a simple-swap hard disk drive.
v The drives that are preinstalled in the server come with power and signal cables attached. If you replace any drives, remember which cable is attached to which drive.
7. Remove the expansion-slot screw 2 at the rear of the adapter 3 if any . 8. Carefully grasp the adapter by its top edge or upper corners. And pull the adapter from the server . Attention: Expansion-slot covers must be installed in all empty slots.
Installing an adapter The following notes describe the types of adapters that the server supports and other information that you must consider when you install an adapter .
6. Remove the screw that secures the expansion-slot cover to the chassis. Store the expansion-slot cover and screw in a safe place for future use. Note: Expansion-slot covers must be installed on all vacant slots. This maintains the electronic emissions standards of the server and ensures proper ventilation of server components.
8. If you are installing a full-length adapter , remove the blue adapter guide (if any) from the end of the adapter . 1 Adapter guide 9. Carefully grasp the adapter by the top edge or upper corners, and align it with the expansion slot guides; then, press the adapter firmly into the expansion slot.
Attention: T o avoid breaking the retaining clips or damaging the adapter connector , open and close the clips gently . 5. Carefully grasp the end of the adapter and pull it out of the connector .
9. T ake the other end of the signal cable that is attached to the drive backplane section for drive bays 0 through 3 (as labeled on the front of the drive cage) and connect it to the connector that is closest to the battery on the PCI card. 10. Replace the hard disk drive fan assembly: a.
5. Align the flash device with the connector on the system board and push it into the connector until it is firmly seated. 6. Press down on the retaining latch to lock the flash device into the USB connector . 7. Reconnect the power cord and any cables that you removed.
4. If you are instructed to return the virtual media key , follow all packaging instructions, and use any packaging materials for shipping that are supplied to you. Installing the virtual media key T o install the virtual media key , complete the following steps: 1.
Removing a hot-swap power supply This procedure applies only to server models that have hot-swap power supplies. See “Installing a non-hot-swap power supply” on page 98 for information about the removal of a non-hot-swap power supply . When you remove or install a hot-swap power supply , observe the following precautions.
T o remove a hot-swap power supply , complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29.
1 Release lever 2 Hot-swap power supply 2. Using the handle, push the power supply toward the front of the chassis until it locks into place. 3. Connect one end of the power cord into the connector on the back of the power supply and connect the other end of the power cord into a properly grounded electrical outlet.
4. Thread the cable through the rope clip and around an object that is not part of or permanently secured to the building structure or foundation, and from which the cable cannot be removed.
68 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide.
2. Install the lower bezel: a. Insert the two bottom tabs on the lower bezel into the matching holes in the front of the chassis. b. Rotate the top of the lower bezel up to the chassis; then, press the blue release tab on the right side of the lower bezel and completely close the lower bezel until it locks securely into place.
Reinstalling the side cover If you removed the side cover , reinstall it. Note: The rear adapter-retention bracket rests against the server side cover . Y ou might find it easier to lay the server on its side to replace the side cover . T o reinstall the side cover , complete the following steps: 1.
Connecting the cables Attention: T o prevent damage to equipment, connect the power cords last. If the server cables and connector panel have color-coded connections, match the color of the cable end with the color of the connector . For example, match a blue cable end with a blue panel connector , a red cable end with a red connector , and so on.
72 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide.
Chapter 6. Installing and replacing customer replaceable units Removing the rear system fan Attention: v Replace a failed fan within 48 hours. v T o ensure proper cooling and airflow , do not operate the server for more than 30 minutes with the side cover removed.
Installing the rear system fan Attention: v Replace a failed fan within 48 hours. v T o ensure proper cooling and airflow , do not operate the server for more than 30 minutes with the side cover removed. T o install the rear system fan, complete the following steps: 1.
Removing the hard disk drive fan assembly This procedure applies only to server models that have a hard disk drive fan assembly . Attention: v Replace a failed fan within 48 hours. v T o ensure proper cooling and airflow , do not operate the server for more than 30 minutes with the side cover removed.
9. Pull out on the hard disk drive fan assembly release tabs; then, rotate the assembly away from the drive cage slightly . 1 Release tabs 2 Hard disk drive fan assembly 3 Slot 10.
1 Release tabs 2 Hard disk drive fan assembly 3 Slot 2. Route the hard disk drive signal and power cables through the slots on the edge of the hard disk drive fan assembly . Make sure that the cables will not be pinched between the hard disk drive assembly and the hard disk drive backplane when the assembly is installed.
5. Connect the hard disk drive fan assembly cable to the system board (see “System-board internal connectors” on page 19 for the location of the hard disk drive fan connector).
1 Retaining tab 2 Drive cage release tab 3 Locating pins 4 Simple-swap backplate 5 Retaining latch 1 1. Lift the simple-swap backplate out of the lower lip on the drive cage and set it aside.
1 Retaining tab 2 Drive cage release tab 3 Locating pins 4 Simple-swap backplate 5 Retaining latch 2. T ilt the top of the simple-swap backplate toward the drive cage and over the locating pins until the retaining latch is engaged securely .
Removing the SAS/SA T A hard disk drive backplane This procedure applies only to hot-swap server models with a SAS/SA T A hard disk drive backplane installed on the back of the hard disk drive cage. T o remove the SAS/SA T A hard disk drive backplane, complete the following steps: 1.
10. T ilt the top of the hard disk drive backplane away from the drive cage until it is clear of the locating pins. 1 1. Lift the SAS/SA T A hard disk drive backplane out of the lower lip on the drive cage and set it aside.
6. Install the hard disk drive fan assembly onto the hard disk drive cage (see “Installing the hard disk drive fan assembly” on page 76). 7. Install the hot-swap hard disk drives that you removed from the hard disk drive cage (see “Installing a hot-swap hard disk drive” on page 51).
1. Position the front end of the front-panel assembly in the channel above drive bay 1 on the left side of the chassis. 2. Push the front-panel assembly 1 toward the front of the chassis until it clicks into place.
7. Squeeze the spring clips 1 on the sides of the front USB connector assembly and pull the assembly out of the back of the housing. 8. Carefully pull the front USB cable out of the opening in the chassis.
9. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server . Removing the rear adapter retention bracket T o remove the rear adapter-retention bracket, complete the following steps: 1. T urn off the server and all attached devices; then, disconnect all power cords and external cables.
Removing the front adapter-retention bracket T o remove the front adapter-retention bracket, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables.
5. Disconnect the cables from the power-supply cage to the system board and all internal components. 6. Remove the four black screws that secure the power-supply cage to the chassis; then, slide the cage toward the front of the server to disengage the retaining clips 1 from the top of the chassis and lift the cage out of the chassis.
2. Install the four screws that secure the power-supply cage to the chassis. 3. Connect the cables from the power-supply cage to the system board and all internal components (see “System-board internal connectors” on page 19 for the locations of the internal connectors).
CAUTION: When replacing the lithium battery , use only Part Number 33F8354 or an equivalent type battery recommended by the manufacturer . If your system has a module containing a lithium battery , replace it only with the same module type made by the same manufacturer .
Removing a ServeRAID BR10-il controller T o remove the ServeRAID BR10-il controller , complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables.
plastic standoff. 3. Connect the signal cable to the SAS/SA T A controller . 4. Install and lock the side cover (see “Installing the side cover” on page 33). 5. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server .
Attention: Some cluster solutions require specific code levels or coordinated code updates. If the device is part of a cluster solution, verify that the latest level of code is supported for the cluster solution before you update the code. T o install a ServeRAID-MR10i adapter , complete the following steps: 1.
7. Press the ServeRAID-MR10i adapter firmly into the connector on the system board. 8. Reconnect the cables to the new ServeRAID-MR10i adapter . Removing an optional ServeRAID-MR10is V AUL T SAS/SA T A controller T o remove a ServeRAID-MR10is SAS/SA T A adapter , complete the following steps: 1.
1 Battery 2 Battery carrier 3 RAID adapter 4 Connector for battery carrier b. Press the battery carrier into the connector on the ServeRAID adapter until it is firmly connected. c. Secure the battery carrier to the ServeRAID adapter with the screws that came with the battery pack.
2 PCI slot 5. Press the ServeRAID-MR10is adapter firmly into the connector on the system board. 6. Reconnect the cables to the new ServeRAID-MR10is adapter . Make sure that the ServeRAID-MR10is SAS/SA T A adapter is cabled. 7. Rotate the rear adapter-retention bracket to the closed (locked) position.
T o remove a non-hot-swap power supply , complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables.
Installing a non-hot-swap power supply This procedure applies only to server models that have a non-hot-swap power supply . See “Removing the hot-swap power supply cage” on page 87 for information about the installation of a hot-swap power supply .
Removing the microprocessor and fan sink T o remove the microprocessor and fan sink, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables.
c. T ip the top of the fan sink toward the front of the server while you slide it away from the lower flange of the retention module; then, remove it from the server . After removal, place the fan sink on its side on a clean, flat surface. Attention: The microprocessor retention latch is spring-loaded when the microprocessor is in place.
Installing a microprocessor and fan sink T o install the microprocessor , complete the following steps: 1. T ouch the static-protective package that contains the microprocessor to any unpainted metal surface on the server . Then, remove the microprocessor from the package.
a. Make sure that the fan sink retention lever is in the fully open position. Important: Be careful when you handle the microprocessor and fan sink. Do not contaminate the thermal material between them.
Note: v Read the Safety information on page vii. v Read the “Installation guidelines” on page 29. T o replace damaged or contaminated thermal grease on the microprocessor and fan sink, complete the following steps: 1. Place the fan sink on a clean work surface.
Removing the system board T o remove the system board, complete the following steps: 1. Read the safety information that begins on page vii and “Installation guidelines” on page 29. 2. T urn off the server and all attached devices; then, disconnect all power cords and external cables.
9. Remove the eight screws (seven in front and one in rear) 1 that secure the system board to the chassis. 10. Slide the system board toward the front of the server to disengage the tabs on the fan sink mounting bracket from the slots on the bottom of the chassis; then, carefully lift the system board out of the server .
12. If you are instructed to return the system board, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.
5. Install the eight screws (seven in front and one in rear) that secure the system board to the chassis. 6. Install any of the following components that you removed from the system board: v The fan connector covers. v Hypervisor key (see “Installing a USB embedded hypervisor flash device” on page 61).
108 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide.
Chapter 7. Configuring the server The following configuration programs come with the server: v Setup Utility The Setup Utility (formerly called the Configuration/Setup Utility program) is part of the server firmware. Use it to change the startup-device sequence, set the date and time, and set passwords.
T able 14. Server configurations and applications for configuring and managing RAID arrays (continued) Server configuration RAID array configuration (before operating system is installed) RAID array m.
Utility , the changes are reflected in the system summary; you cannot change settings directly in the system summary . – Product Data Select this choice to view the system-board identifier , the revision level or issue date of the firmware, the integrated management module and diagnostics code, and the version and date.
- Network Configuration Select this choice to view the system management network interface port, the IMM MAC address, the current IMM IP address, and host name; define the static IMM IP address, subnet mask, and gateway address; specify whether to use the static IP address or have DHCP assign the IMM IP address; save the network changes.
v User Security Select this choice to set, change, or clear passwords. See “Passwords” for more information. This choice is on the full and limited Setup Utility menu. – Set Power-on Password Select this choice to set or change a power-on password.
password has access to only the limited Setup Utility menu; the user can set, change, and delete the power-on password, if the system administrator has given the user that authority . Power-on password If a power-on password is set, when you turn on the server , the system startup will not be completed until you type the power-on password.
RAID controllers The following table lists the various utilities available to configure RAID controllers before an operating system is installed. T able 15.
1. After you turn on the power and when the computer is starting, you are prompted to press Ctrl + H when the following message is displayed: Copyright© LSI Logic Corporation Press <Ctrl><H> for WebBIOS 2. Select an adapter from the list.
New Configuration Clears the existing configuration and lets you create a new configuration. Add Configuration Retains the existing storage configuration and adds new drives to it (this does not cause any data loss).
The EasyStartup program has the following features: v Self-booting DVD v Easy-to-use, language-selectable interface v Integrated help system v Automatic hardware detection v RAID configuration utility.
If you continue to the main program interface, you will have the following selectable options: v Compatibility notes: This selection provides information about the RAID controllers, operating systems, and server configurations supported by that version of the EasyStartup program.
– Integrated Mirroring Enhanced (IME) with hot-spare support (also known as RAID 1E) Use this option to create an integrated mirror enhanced array of three to eight disks, including up to two optional hot spares. All data on the array disks will be deleted.
4. T o highlight the drive that you want to format, use the Up Arrow and Down Arrow keys. T o scroll left and right, use the Left Arrow and Right Arrow keys or the End key . Press Alt+D. 5. T o start the low-level formatting operation, select Format and press Enter .
v Save response file: This task gives you the option of saving the information on a diskette or USB device as a response file for future installations on similarly configured Lenovo servers. v Start installation: This task starts the actual installation process.
v SAS firmware is stored in ROM on the integrated RAID controller on the system board. v Major components contain vital product data (VPD) code. Y ou can select to update the VPD code during the UEFI code update procedure. The following items are downloadable at http://www .
The IMM supports the following basic system management features: v Environmental monitor with fan speed control for temperature, voltages, fan failure, power supply failure, and power backplane failure.
identify the server , and perform other management functions. Any standard T elnet client application can access the SOL connection. Using the remote presence capability and blue-screen capture The remote presence and blue-screen capture features are integrated functions of the integrated management module (IMM).
2. On the Login page, type the user name and password. If you are using the IMM for the first time, you can obtain the user name and password from your system administrator .
v The server is not a domain controller . However , it is recommended to have the server join a domain. v The account that you use to log in and to install the Core Server has Administrator privileges on the server with full read/write access. Ideally , this account is also a Domain Administrator account.
v ASP .NET v ASP v CGI v Server Side Includes v Windows Authentication v IIS 6 Metabase Compatibility Note: When you select ASP .Net or ASP , a dialog box displays the additional role services required. Click Add Required Role Services . 6. Click Install .
Chapter 8. T roubleshooting This chapter describes the diagnostic tools that are available to help you solve problems that might occur in the server . If you cannot diagnose and correct a problem by using the information in this chapter , see Appendix A, “Getting help and technical assistance,” on page 179 for more information.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
Keyboard, mouse, or pointing-device problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
Memory problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
Microprocessor problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
Monitor problems Some monitors have their own self-tests. If you suspect a problem with your monitor , see the documentation that comes with the monitor for instructions for testing and adjusting the monitor . v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
Power problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
Software problems v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the parts listing in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRUs) and which components are field replaceable units (FRUs).
2. Check for loose cables in the power subsystem. Also check for short circuits, for example, if a loose screw is causing a short circuit on a circuit board.
Solving undetermined problems If the diagnostic tests did not diagnose the failure or if the server is inoperative, use the information in this section. If you suspect that a software problem is causing failures (continuous or intermittent), see “Software problems” on page 140.
v System-event log: This log contains all IMM, POST , and system management interrupt (SMI) events. Y ou can view the system-event log through the Setup Utility and through the Dynamic System Analysis (DSA) program (as the IPMI event log). The system-event log is limited in size.
4. Click Downloads and drivers to download firmware updates. If IPMItool is installed in the server , you can use it to view the system-event log. Most recent versions of the Linux operating system come with a current version of IPMItool.
POST error codes When you turn on the server , it performs a series of tests to check the operation of the server components and some optional devices in the server . This series of tests is called the power-on self-test, or POST . If a power-on password is set, you must type the password and press Enter , when you are prompted, for POST to run.
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
v Follow the suggested actions in the order in which they are listed in the Action column until the problem is solved. v See the ″ Parts Listing ″ section in the Hardware Maintenance Manual to determine which components are customer replaceable units (CRU) and which components are field replaceable units (FRU).
Note: After you exit from the stand-alone memory diagnostic environment, you must restart the server to access the stand-alone memory diagnostic environment again. 5. Select gui to display the graphical user interface, or select cmd to display the DSA interactive menu.
T o save the DSA log to a file on a diskette or to the hard disk, click Save Log on the diagnostic programs screen and specify a location and name for the saved log file. Notes: 1. T o create and use a diskette, you must add an optional external diskette drive to the server .
Appendix A. Getting help and technical assistance If you need help, service, or technical assistance or just want more information about Lenovo products, you will find a wide variety of sources available from Lenovo to assist you.
Calling for service During the warranty period, you can get help and information by telephone through the Customer Support Center . These services are available during the warranty period: v Problem d.
Service methods and procedures vary by country , and some services might not be available in all countries. International W arranty Service is delivered through the method of service (such as depot, carry-in, or on-site service) that is provided in the servicing country .
182 ThinkServer TS200 T ypes 6522, 6523, 6524, 6525, 6526, 6528, 6529, and 6530: Installation and User Guide.
Appendix B. Notices Lenovo may not offer the products, services, or features discussed in this document in all countries. Consult your local Lenovo representative for information on the products and services currently available in your area.
estimated through extrapolation. Actual results may vary . Users of this document should verify the applicable data for their specific environment. T rademarks The following terms are trademarks of Le.
Lenovo makes no representation or warranties regarding non-Lenovo products and services, including but not limited to the implied warranties of merchantability and fitness for a particular purpose. These products are of fered and warranted solely by third parties.
L ’etiquette du système respecte la Directive européenne 2002/96/EC en matière de Déchets des Equipements Electriques et Electroniques (DEEE), qui détermine les dispositions de retour et de recyclage applicables aux systèmes utilisés à travers l’Union européenne.
T able 17. Limits for particulates and gases (continued) Contaminant Limits 1 ASHRAE 52.2-2008 - Method of T esting General V entilation Air-Cleaning Devices for Removal Efficiency by Particle Size . Atlanta: American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc.
Battery return program This product may contain a lithium or lithium ion battery . Consult your user manual or service manual for specific battery information. The battery must be recycled or disposed of properly . Recycling facilities may not be available in your area.
batteries pour indiquer que la batterie ne doit pas être mise au rebut mais plutôt récupérée en fin de cycle de vie selon cette norme. In accordance with the European Directive 2006/66/EC, batteries and accumulators are labeled to indicate that they are to be collected separately and recycled at end of life.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Dieses Produkt entspricht den Schutzanforderungen der EU-Richtlinie 2004/108/EG (früher 89/336/EWG) zur Angleichung der Rechtsvorschriften über die elektromagnetische V erträglichkeit in den EU-Mitgliedsstaaten und hält die Grenzwerte der EN 55022 Klasse A ein.
Japan V oluntary Control Council for Interference (VCCI) statement T aiwan Class A warning statement People’s Republic of China Class A warning statement Korea Class A warning statement 192 ThinkSer.
Index A acoustical noise emissions 1 1 adapter hot-plug devices 92 installing 57 hot-plug 92 PCI card installing 60 removing 55 requirements 57 scanning order 57 ServeRAID-MR10i 92 ServeRAID-MR10is in.
diskette drive (continued) removing 44 display problems 135 documentation DVD 3 drive cables 54 removable-media 47, 48 drive bays, internal 43 drives bay 1, 2, or 3 installing 45 hot-swap SAS cabling .
H H8 heartbeat LED 24 handling static-sensitive devices 31 hard disk drive diagnostic tests, types of 131 formatting 120 problems 130 status LED 17 hard disk drives hot-swap SAS or SA T A, installing .
LEDs (continued) rear of server 18 LEDs and controls on the front of the server 15 logs system-event message 144 lower bezel installing 69 removing 34 LSI Configuration program 1 19 M management, syst.
reliability 12 remote presence feature functions 8 using 125 removing adapter 55 battery 89 CD drive 44 connector 62 cover 32 DIMMs 37 diskette drive 44 DVD drive 44 fan hard disk drive, assembly 75 r.
system board (continued) removing 104 switches and jumpers 21 system reliability guidelines 30 system-board error LED 23 system-error LED 17 system-event log 143 system-information LED 17 system-locat.
.
Printed in USA.
Ein wichtiger Punkt beim Kauf des Geräts Lenovo 6522 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Lenovo 6522 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Lenovo 6522 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Lenovo 6522 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Lenovo 6522 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Lenovo 6522 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Lenovo 6522 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Lenovo 6522. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Lenovo 6522 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
