Benutzeranleitung / Produktwartung AP9810 des Produzenten APC
Zur Seite of 32
Inst allation and Configuration Dry Cont act I/O SmartSlot Card AP9613.
This manual is available in English on the enclosed CD..
Content s Dry Contact I/O SmartSlo t Card i Safety Overview 1 Important Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product Overview 2 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dry Contact I/O SmartSlo t Card ii Disclaimer 20 APC Worldwide Customer Support 32.
Dry Contact I/ O SmartSlot Card 1 Safety Overview Import ant Safety Information Follow all applicable electrical codes for your installation area. Read the instructions care fully to becom e familiar with the equipment before trying to install, operate, service or maintain it.
2 Dry Contact I/ O SmartSlot Card Product Overview Introduction The Schneider Electric™ Dry Contact I/ O SmartSlot Card (AP9613) is a management product that provides the fo llowing features: • UPS status information presented through 6 fully isol ated ou tput relays.
Dry Contact I/ O SmartSlot Card 3 Hardware and sof tware re quirements and tools needed The Dry Contact I/O SmartSlot Card works with most APC by Schneider Electric UPS devices with an output rated less than or equal to 160kV A and an available SmartSlot.
4 Dry Contact I/ O SmartSlot Card Showing the product det ail Itemizing the features of the Dry Contact I/O SmartSlot Card .
Dry Contact I/ O SmartSlot Card 5 Item Name Description Universal I/O ports 1 and 2 These support the AP9335 T/ TH and AP9810 dry contact accessories USB cable connector Connecting this to your PC enab les usage of the Configuration Utility . Reset button Use an appropriately sized, non-metallic tool to press the Reset button.
6 Dry Contact I/ O SmartSlot Card Itemizing the input cont act and output relay terminal blocks Number of positions on each terminal block 9 T ightening torque 0.35 N.m T ightening torque max 0.4 N.m W ire stripping length 5 mm Minimum wire gauge 0.14 mm 2 (26 A WG) Maximum wire gauge 2.
Dry Contact I/ O SmartSlot Card 7 Configuring th e Dip Switches The Dry Contact I/O SmartSlot Card requires configuration before test ing , final installatio n, and use. See “Location of dip switch es” directly below and “Dip switches: input and outputs” .
8 Dry Contact I/ O SmartSlot Card Dip switches: input and output s The table below lists the fo ur possible configurations, wi th their corresponding inputs and outputs. * W ith this setup (the factory default), the Configuration Utility is used automatically .
Dry Contact I/ O SmartSlot Card 9 Inst alling See “Planning your installatio n” directly below , “Installation steps” on page 12, and “Connecting to the configurati on uti lity” on page 14.
10 Dry Contact I/ O SmartSlot Card inputs, we recommend that an outpu t be configured and monitored appropriately to determine th e effectiveness of an input. • Do not wire this Dry Contact I/O SmartSlot Card when the pow er is on. • The installation of this Dry Contact I/O SmartSlot Card must fol low applicable building and electrical codes.
Dry Contact I/ O SmartSlot Card 11 Connection strategies Y ou can connect the alarm outputs of th e Dry Contact I/O SmartSlot Card in several ways to meet the requirements of your manage ment systems or switched load. Both normally open (N. O.) and normally closed (N.
12 Dry Contact I/ O SmartSlot Card Inst allation step s W arning: After installat ion, it is stro ngly recommended that you fully test your configuration before puttin g it into a production environment. 1. Make all connections to the Dry Co ntact I/O SmartSlot Card to support your configurat ion before continuing .
Dry Contact I/ O SmartSlot Card 13 3. Orient the Card to fit in the Card slot as shown. Slide th e Card all the way into the slo t until the end plate is flush with the back p anel of the host device. T rying to inst all the Card upside down may damage it.
14 Dry Contact I/ O SmartSlot Card Connecting to the configuration utility The Configuration Utilit y does not need to be installed, it runs off the Card.
Dry Contact I/ O SmartSlot Card 15 T o run the Utility , launch the runme.hta file located in the root of the drive. For information on using the Configuration Utility user interface, refer to its online help. When you connect your Card with your PC using the USB cable, the Configuration Utili ty reads a file called config.
16 Dry Contact I/ O SmartSlot Card S pecifications For all specifications, when there is a dif ference between the VDE and UL approval standards, use the lower rating.
Dry Contact I/ O SmartSlot Card 17 Ratings for input cont acts and output relays Relative Humi dity Operating Sto ra ge 0 to 95% 0 to 95% Approvals Emissions and Immuni t y V erification: FCC Part 15 .
18 Dry Contact I/ O SmartSlot Card Wa r r a n t y T wo-Y ear Factory W arranty This warranty applies only to the products you purchase for your use in accordance with this manual. T erms of warranty APC warrants its products to be free from defects in materials and workmanship for a period of two years from the date of purchase.
Dry Contact I/ O SmartSlot Card 19 OTHER ADVICE OR SER VICE IN CONNECTION WITH THE PRODUCTS. THE FOREGOING W ARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER W ARRANTIES AND REMEDIES. THE W ARRANTIES SET FOR TH ABOVE CONSTITUTE APC’S SOLE LIABILITY AND PURCHASER’S EXCLUSIVE RE ME DY FOR ANY BREACH OF SUCH W ARRANTIES.
20 Dry Contact I/ O SmartSlot Card Disclaimer The information presented in this manual is not warranted by Schneider Electric to be authoritative, erro r free, or complete.
.
.
.
.
.
.
.
APC W orldwide Customer Support Customer support for this or any other product is available at no charge in any of the following ways: • V isit the APC W eb site to access documen ts in the APC Know ledge Base and to submit customer support requests.
Ein wichtiger Punkt beim Kauf des Geräts APC AP9810 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie APC AP9810 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für APC AP9810 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von APC AP9810 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über APC AP9810 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon APC AP9810 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von APC AP9810 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit APC AP9810. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei APC AP9810 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
