Benutzeranleitung / Produktwartung WS-7014U-IT des Produzenten La Crosse Technology
Zur Seite of 19
WS-7014U-IT Wireless 915 MHz Radio-controlled Weather Station Instruction Manual.
2 TABLE OF CONTENTS Topic Page Inventory of Contents/Additional Equipment 3 About WWVB 3 Quick Set-Up Guide 4 Detailed Set-Up Guide Battery installation 5 Program Mode Program Sequence and Default Set.
3 INVENTORY OF CONTENTS 1. The Wireless Weather Station/ (Figure 1). 2. One remote temperature sensor with mounting bracket (Figure 2). 3. Three each, ½” Philips screws. 4. One strip double-sided adhesive tape. 5. Instruction manual and warranty card.
4 signal continuously throughout the United States at 60 kHz. The signal can be received up to 2,000 miles away through the internal antenna in the Weather Station. However, due to the nature of the Earth’s Ionosphere, reception is very limited during daylight hours.
5 DETAILED SET-UP G UIDE I. BATTERY INSTA LLATION (When one temperature sensor is being used) 1. First, insert the batteries to the temperature sensor (see “ A . Remote Temperature Sensor ” below). 2. Within 2 minutes of powering up the sensor, insert the batteries to the Weather Station (see “ B.
6 • If the signal reception is not successful on the first frequency (915MHz) for 45 seconds, the frequency is changed to 920MHz and the learning is tried another 45 seconds. If still not successful the reception is tried for 45 se conds on 910MHz. This will also be done for re- synchronization.
7 Note: There are 8 LCD contrast levels to choose from—“Lcd 0” is the lightest, and “Lcd 7” is the darkest. 3. Press and release the IN button to select the level you desire. 4. Press and release the SET button to confirm and advance to the Time Zone setting.
8 “DST 0” indicates that the feature is off and the WWVB will not change times automatically. “DST 1” indica tes that the feature is on and the WWVB will change times automatically. Note: Some locations (Arizona and parts of Indiana) do not follow Daylight Saving Time, and should select “DST 0.
9 conducts a WWVB search every night between these hours, and overrides any manually set time. The WWVB tower icon (appearing in the TIME LCD) will flash when a signal-search is in progress and a signal is being received, and will remain steady when the signal has been received.
10 XI. SELECTING ° F OR ° C 1. Press and hold the SET button for 5 seconds. 2. “LCD” will show in the time LCD and the number setting will flash. 3. Press and release the SET button nine times. 4. Either ” ° F” or “ ° C” will flash in the time LCD.
11 FEAT URES OF THE WS-7014U-IT I. WEAT HER FORECAST The weather forecasting feature is estimated to be 75% accurate and is for the next 12 to 24 hours.
12 should be viewed as a generalization of the expected weather change (for example a “sunny” icon indicates the weather is expected to improve). The weather icons change when the unit detects a change in air pressure. The icons change in order, from “sunny” to “partly sunny” to “cloudy ” or the reverse.
13 2. Press the IN button again (once while “MIN” is still displayed, twice otherwise). “MAX” appears above the indoor temperature and the LCD will flash, indicating that the maximum temperature (along with the humidity measured at that time) and the time and date of occurrence are displayed.
14 LCD after 60 seconds, remove the batteri es and wait for at least 60 seconds before reinserting them. 4. The outdoor temperature from the first sensor (channel 1) should then be displayed on the Weather station.
15 reach the remote temperature sensor or Wi reless Weather Station. While the remote temperature sensor is weather proof, av oid submersion in water or snow.
16 The Wireless Weather Station comes with the table stand already mounted. If you w ish to use the table-stand all that is required is to place the Wireless Weather Station in an appropriate location. B. WALL MOUNTING 1) Remove the table-stand. To do this, pull down on the stand from the rear and rotate forward.
17 harder to compare different ranges with different curves. Under non-laboratory conditions, it is difficult to compensate for the above factors and obtain an accurate comparison. MAINTENA NCE A ND CARE INSTRUCTIONS • Extreme temperatures, vibration, and shock should be avoided to prevent damage to the units.
18 determination and service procedures. Warranty service can only be performed by a La Crosse Technology, Ltd authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to La Crosse Technology, Ltd or La Crosse Technology, Ltd’s authorized service center.
19 support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacrosse te chnology.com Questions? Instructions? Please visit: www.
Ein wichtiger Punkt beim Kauf des Geräts La Crosse Technology WS-7014U-IT (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie La Crosse Technology WS-7014U-IT noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für La Crosse Technology WS-7014U-IT - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von La Crosse Technology WS-7014U-IT reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über La Crosse Technology WS-7014U-IT erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon La Crosse Technology WS-7014U-IT besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von La Crosse Technology WS-7014U-IT verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit La Crosse Technology WS-7014U-IT. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei La Crosse Technology WS-7014U-IT gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
