Benutzeranleitung / Produktwartung ATX 12V des Produzenten AB Soft
Zur Seite of 97
• Please read the users guide be fore proceeding with yo ur inst allati ons. Seri ous damage m ay occur if the procedure is not followed pr operly . • This mot herboar d does not suppor t CPUs wi th a Vcor e highe r tha n 1.6 volts. P lease make sure the CPU yo u are using 1.
SY -P4I865PE Plus DRAGON 2 Motherboard ************************** ************************** mPGA Socket 478 Processor supported Intel 865PE AGP/PCI 400/533/800 MHz Front Side Bus supported A TX 12V F.
SOYO ™ SY -P4I865PE Plus DRAGON 2 iii Copyright © 2003 by Soyo Co mputer Inc. T rad emarks: Soyo is the registered trademark of Soyo Computer Inc. All trademarks are the properties of their owners. Pr oduct Rights: All names of the produ ct and corporate mentioned in t his publication are used for identification purposes only .
T able of Contents SY -P4I865PE Plus DRAGON 2 iv T able of Co ntents CHAPTER 1 MOTHERBOARD DESCRIPTION ......... ............ .......... 1 1-1 INTROD UCTION ......... ................................................... ............ 1 1-2 UNP ACKING THE MOTHERBOARD .
T able of Contents SY -P4I865PE Plus DRAGON 2 v 3-4 ADV ANCED CHIPSET FEA TURES ... .............................. ........ 63 3-5 INTEGRA TED PERIPHERALS ....... ................ ............... .......... 65 3-6 POWE R MANAGEMENT SETUP ...... ......
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 1 Chapter 1 MOTHERBOARD DESCRIPTION 1-1 INTRODUCTION The SY -P4I865PE Plu s DRAGON 2 AGP/PCI Moth erboard is a high-per formance S ocket 478 proc essor support ed A TX 12V form-factor system board.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 2 One Back panel Wa r n i n g : Do not unpack th e Mother board from i ts ant i-st atic packagi ng unti l you ar e ready t o install it. Like most el ectroni c equipme nt, your Motherboar d may be da maged by electrostatic discharge.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 3 1-3 KEY FEA T URES CPU Supports I ntel® mPGA Socket 478 processors : Pentium® 4 with and without Hyperthr eading, Nort hwood, .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 4 S torage ICH5 integrated Se rial A T A c ontroller supporting up to 2x UDMA 1 50 hard disks ICH5 Integra ted Parallel A T A controller supporting up to 4x UDMA 33/66/100 Paralle l A T A dev ices.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 5 Wa r n i n g : Do not apply power if the Motherboard appears damag ed. If t here is damage t o the board, conta ct your deal er immedia tely . 1-5 ELECTROST A TIC DISCHARGE PRECAUTIONS Make sure to ground yourse lf be fore handl ing th e Motherboa rd or othe r system compon ents.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 6 1-6 SY -P4I865PE PLUS DRAGON 2 MOTHERBOARD LA YOUT Back Panel SY -P4I865PE Lite DR AGON 2 Platform PS/2 K B Connector PS/2 Mous e PS.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 7 1-7 SY -P4I865PE PLUS DRAGON 2 MOTHERBOARD COMPONEN TS A BCDE F G H I J K L M N O P Q R S T U V W X Y Z AA AB AC AD AE.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 8 A +12V Power Conne ctor This is where the Power Supply's +12V A TX connector goes. For a lay-out of this connector pl ease check the F. A T X 1 2 V P o w e r Supply paragraph on page 3 5.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 9 H CPU Cooling Fan (CPUF AN1) connectors W ith these connect ors you ca n att a ch the CPU f an or fans to your motherboard. They supply power an d (in the case of CPUF AN1) allow you to m onitor the speed of the F AN via the SOYO Hardware Monitor software or vi a CMOS setup.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 10 O Chassis Cooling Fan (CHA F AN1) co nnector This co nnec tor is to con nect y our ch assis fan to yo ur moth erbo ard. This mother board supports up t o 2 chassis fans. It allows you to monitor the speed of CHAF AN1 in CMOS setup or by using the SOYO Hardware Monitor software.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 11 V GAMEPOR T connector This co nnec tor is to at tach y our gameport conne ctor to. Ga meport s are used to con nect for example joysticks to. For more details check the pa ragraph on page 30.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 12 AC AC97 Onboar d Audio Chip AD Micr ophone and LAN S tatus LED Connector (J30 ) This connector allows you to exte nd your microphone conn ector and LAN Status LED to your fro nt panel.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 13 Chapter 2 HARDW ARE INST ALLA TION Congratul ations on your purchase of SY -P4I865PE Plus DRAGON 2 Motherboar d.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 14 2-2 IN ST ALLA TION GUIDE W e will now be gin th e inst allation of the Mot herboard. P lease follow t he step-by-step p rocedure designed to lead you to a complete and correct install ation.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 15 2. Align t he blunt edge of the CPU wi th the matching p inhol e disti nctive edge on the socket.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 16 4. Th en close the socket handle to secure the C PU in p lace. Remember to co nnect the CPU Cooling Fa n to the appropriate power connector on the Motherboard. The fan is a key component that will ensure syst em st ability .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 17 Step 2 Inst all Memory Module This moth erboar d supports one Dual Channe l to your memory , Not e that you can use normal DD R memory for Dual Channel to work. Also note that for Dual Channel to work 2 modules of equal size and specifications h ave to be installed .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 18 Memory Configuration T able If you want to use the Dual Channel feature, pl ease f ollow the memo ry configur ation tabl e below: Instal ling your memo ry in a combi nati on di f fe rent fr om the ta ble a bove wil l still a llow your system to wor k.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 19 S tep 3 Inst allation of Exp ansion Cards The mothe rboa rd has 1 AGP sl ot and 5 PCI sl ots. 1. R ead the relate d exp ansio n card’ s instruction document before inserting the expansi on card into the comput er .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 20 S tep 4 Connect cables, case wire, and power supply A.IDE Device In stallation (HDD, CD-ROM) This Mothe rboard offers 1 pri mar y (IDE1) I DE devic e connector s, 1 secondary ID E device c onnector s (I DE2) and 2 ter tiary serial A T A ports.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 21 Note: I DE2 and SA T A2 ar e not boot able, SA T A1 and IDE1 are boot able. Note: Only W in dows XP can use SA T A1, S A T A2, IDE1 and IDE2 at the same time.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 22 Serial A T A connectors Y ou c an also pl ug the ser ial A T A cable i nto the serial A T A connector of the motherboar d. The other end of t he SA T A cable goes into your SA T A devi ce.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 23 B. Floppy Drive Installation The system support s 5 possibl e floppy dri ve types: 720 KB, 1. 2 MB, 1. 44 MB, 2.88 MB. In addition, t his Motherboa rd supports a 3-mode (720KB/1.2M B/1.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 24 C. Fr ont Panel Connections Plug the c ompute r case's fr ont panel devi ces to t he corr esponding he ader s on the Mot herboard . 1. Power LED Please i nstall accor ding t o the fo llowing pi n assi gnment : pin 1, 3 ar e for Power LED.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 25 2. Reset Plug t he Reset push- butt on cabl e int o the 2-pi n Reset he ader on t he Mo therbo ard. Pu shin g the R eset b utton on the front p anel w ill ca use t he system to restar t the boot- up sequence .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 26 5. IDE LED Attach the 2-pin IDE device LED ca ble to the correspondi ng IDE LED header on the Motherboard. This will cause the LED to lighten when an IDE1 o r IDE2 (HDD, CD-R OM) device is active.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 27 D. Back Panel Connect ions All external devices such as the PS/2 ke yboard, P S/2 mouse, printer , modem, USB can be plugged di rect ly int o the Mother board back pa nel.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 28 1. Onboar d Serial Ports COM A/COMB External periph erals that use seri al transmission scheme include: - serial (RS232) mice - modem. Plug th e serial devi ce ca bles di rectly into t he COMA/COMB 9- pin mal e connectors loc ated at the rear pan el of the Motherbo ard.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 29 5. Univer sal Serial Bus (USB1/US B2, USB3/USB4, USB20_1/ USB20_2) This Motherboard provides 8 USB 2.0 po r ts for your addi ti onal devices. Plug the USB device jack into the available U SB connector USB1, USB2, USB3 and USB4.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 30 The Gameport has the following lay-out : E. Other Connections 1. S t andard Infrared (SIRCON) Plug the 5- pin i nfrar ed device cabl e to t he SIRCON header . This will e nable the i nfrared tra nsfer f unction.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 31 2. Coolin g Fan Inst allati on (1) CPU C ooling Fan (CPUF AN1) Afte r you have seat ed the CP U properl y on the pr ocessor , at tach t he 3-pin fan cable to the CPUF AN connector on the Motherboard.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 32 (2) Chassis Cooling Fan (CHAF AN1, CHAF AN2) Some chassis also feature a cooling fan. This Motherboard features a CHAF AN connector to provide 12V pow e r to the chassis fan. Connect the cable fr om the chassi s fan t o the CHAF AN 3-pi n connector .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 33 3. Smart Card Re ader The smart card reader confo rms to the PC/SC W orking group standar d, and has the foll owing lay-out: 4. CD Line-in (CDIN1) This Motherboard prov ides one CD-Line-in con nectors.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 34 5. AUX-IN (AUXIN1) This Motherboard p rovides one AUX-IN connecto rs. Please connect the 4-pin audio cable from your second CD-ROM or DVD ROM drive to either AUX-IN. Please i nstall ac cording to the followi ng pin assignment: 6.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 35 F . A TX12V Power Su pply The power supp ly connector is the la st connecti on to be made whil e install ing a mot herboar d. This mot herboa rd re quires an A TX 12V powe r supply (For P4 syste m), and A T or A TX power supply ca nnot be used.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 36 3.3V -12V GN D PS -ON GN D GN D GN D -5V 5V 5V 3.3V 3.3V GN D 5V GN D 5V GN D PW- OK 5VS B 12V AT X P o w e r Note 3: The minimum r.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 37 G . CMOS Clear (JP5) In some cases t he CMOS memor y may cont ain wr ong data, foll ow the st eps below to c lear the CMOS m emory . 1. Clear the CMOS memory by mome ntarily shor ting pi n 2-3 on jumper JP 5.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 38 Onboard LAN LED Definition S tep 5 Power On Y ou have now comple ted th e hardwa re i nstall ation of y our Mot herbo ard successfully .
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 39 Repeat thi s operati on until you get t he foll owing scr een. 3. Th e BIOS Setup screen appears: Phoenix – A war d BIOS CMOS Set.
H a rd w a re I n s t a l l a t i o n SY - P4I865PE Plus DRAGON 2 40 Step 1. Select [ST AND ARD CMOS SET UP] Set [Date/T ime] and [Floppy drive type], then set [Hard D isk T ype] to “Auto”.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 41 Chapter 3 BIOS SETUP UTILITY This Mot herboard's BI OS setup pr ogram us es the ROM PCI BIOS progra m from A ward Software Inc. T o enter the A ward BIOS prog ram's Main Me nu: 1. Tu rn on or reboot the syst em.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 42 Hot Keys: Function keys give you a ccess t o a group of commands throughout t he BIOS uti lity . Function Comman d Description F1 Gener al He l p Gives the list of opti ons available for each item. F5 Previ ous Va l u e s Restore the old values.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 43 SA VE AND EXIT SETUP Select the [SA VE & EXIT SETUP] option from the M ain M enu to sav e data to CMOS and exit the set up util ity . Th is opti on saves all your changes and causes the system to reboot.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 44 3-1 SOYO CO MBO FE A TURE This mot herboard doe s not use any hard ware ju mpers to se t the CPU frequency .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 45 System Perform ance Setting Description Note Normal Default Fast System Performance Tu r b o Adjust your comput er ’ s perform ance. SOYO COMBO Feature Setting Description Note CPU Clock Ratio 8X~ 50X The available CPU ra tio you can select w ill depends on your CPU ID.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 46 SOYO C OMBO Fe ature (C ontinue) Setting Description Note Disabled Quick Power On Self T est Enabled Provi des a f ast POST at boot -up. Default Enabled C.I .H. 4 -W A Y Pr otection Di sab le d This item allo ws yo u write-protect your BIOS chip.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 47 3-1.1 Adv anced DRAM Control Caution: Change these se ttings only if y ou are already fa miliar with DRAM timi ng para mete rs. The [A dvanced DRAM Control] op tion changes the values of the chipset registers.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 48 CHIPSET FEA TURES SETUP (Continue) Setting Descript ion Note 2 3 DRAM RAS# to CAS# Delay 4 This item allo ws you to control DRAM RAS to CAS delay time. Default 2 3 DRAM RAS# Precharge 4 This item allo w you to co ntrol DRAM RAS percharge time.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 49 3-1.2 On board Device The [Onboard De vice] opt ion changes t he val ues of the chi pset regi sters. These registers con trol the system options in the computer .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 50 3-1.3 O nChip IDE Device Caution: Change the se settings onl y if you ar e alre ady fami liar with the IDE s etting s. The [OnChip IDE Devi ce] option change s the setti ngs of t he 82801EB (ICH5) IDE controlle r .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 51 CHIPSET FEA TURES SETUP Setting Descri ption Note IDE only Only enabl ed IDE1,2. SA T A1,2 are disabled Defa ult SA T A only O nly enable SA T A1,2. IDE1,2 are d isabled. Pri IDE+SA T A IDE1 and SA T A1,2 are enabled.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 52 IDE Device Controls Setting Description Not e Disabled T urn of f the on-boa rd IDE On-Chip PCI IDE Prim ary Secon dary Enabled Use the on -bo.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 53 3-1.4 Boo t Device Order The [Boot De vice Order] opt ion al lows you to change t he order in whic h your system scans for devices to boot f rom.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 54 System Boot Control Settings Setting Description Note Floppy LS120 IDE1/SA T A1 CDROM ZIP100 Other Devi ce First /Sec ond/Thi rd Boot Device Dis abl ed Selects the ord er in which your system scans for devi ces t o boot fr om (First th e first boot device, t hen the second, etc…).
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 55 3-2 ST ANDARD CMOS SETUP Select the [ST ANDARD CMOS SETUP] opti on fr om the Main Menu and press [Enter ] key .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 56 Hard Disks T ype & Mode Choose the type and mode for the har d disks that you have al ready i nstall ed.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 57 Others Optional Setting Description Note EGA/VGA Default CGA 40 CGA 80 Vi d e o MONO (Monochr ome) Selec t the v ideo mode . ALL Err or s Default No Errors All, But Keyboard All, But D iskette Halt On All , But Di sk/Key When th e BIOS detec ts system errors, this fun ction will stop the syste m.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 58 3-3 ADV ANCED BIOS FEA TURES Select the [Ad vanced BIOS Features] option f rom the Main Menu and press [Ente r] key .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 59 V irus W arning Setting Descriptio n Note Disabled Default V irus W arnin g Enabled Allows you to choose the VIRUS warning feature for IDE Hard Disk bo ot sector protecti on.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 60 Boot Up NumLock St atus Setting Description Note On N umeric keypad in numeric mode at boot -up. Default Boot Up NumLock St a t u s Off Puts numeri c keyp ad in arrow key mode at boot-up. Gate A20 Options Setting Descriptio n Note Normal A pi n in t he keyboar d contr oller controls G ateA20 .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 61 Security Option Use this feature to p rev ent unauthori zed system b oot -up or use of BIOS Setup. The following table describes t he securit y settings. Setting Descriptio n Note Setup If a password is set, the password prompt only appears when you attempt to enter the BI OS Setup prog ram.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 62 LOGO Show Setting Descriptio n Note Disabled Full Screen LOGO Show Enab led Set Enabled to Show Logo (DRAGON). Defa ult LOG0 Default EP A LOGO SELECT LOG1 Allows user to display SOYO logo or own logo. Logo-0 shows SOYO logo, Logo -1 shows user logo .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 63 3-4 ADV ANCED CHIPSET FEA T URES Caution: Change these se ttings only if y ou are already fa miliar with the C hips et. The [Advance d Chipset Featur es] option changes the values of the chipset registers.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 64 CHIPSET FEA TURES SETUP Setting Description Note Disabled Defa ult System BIOS Cacheable Enab led The ROM area F0000H-FFFFF H is cacheable. Disabled Defa ult Vi d e o B I O S Cacheable Enab led The video BIOS area at C0000H-C7FFFH is cach eable.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 65 3-5 INTEGRA TE D PERIPHERALS Caution: Change these se ttings only if y ou are already fa miliar with the C hips et. The [INTEGRA TED PERIPHERALS] opti on changes the values of the chipset registers. These registers contro l the system options in the computer .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 66 3-5.1 Onboa rd USB Device This [Onboar d USB Device ] option chan ges t he values of the onboard USB controll er . The following screen show s setup default setti ng. Phoenix – A ward BIOS CMOS Setup Utili ty Onboard US B Devi ce USB Controller Enabled USB 2.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 67 3-5.2 Supe rIO Device Caution: Change these se ttings only if y our are already fa miliar with the C hips et. The [Sup erIO Device] option chang es the values of the Super I /O controller . The following screen show s setup default setti ngs.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 68 Others Optional Setting Descriptio n Note Password Enables you to wa ke-up the system by entering a password on the keyboard. Hot KEY Y ou can wake-up the system by pressing t he key combinat ion of your choice ( Ctrl-F1~ F12).
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 69 Onb oa rd Seri al Por t s Setting Descript ion Note Normal Default IrDA ASKIR UAR T Mod e Select SCR The second serial p ort offers several special modes. It can either work as an infrared device (IrDA, ASKIR) or as a Smart Card reader (S CR), or as a normal serial port.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 70 Others Optional Setting Descript ion Note On The system will switch on when power comes back after a power failu re.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 71 3-6 POWER MA NAGEMEN T S ETUP The [POWER MANAG EMENT SETUP] se ts the system's power saving functions.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 72 Power Management Controls Setting Description Note S1(POS) Default S3(STR) ACPI Su spend Ty p e S1 & S3 This item a llows you se lect suspend mode. Auto Default Ye s Run VGABIOS if S3 Resume No Some OS (win xp/ 2k) r equir e to load VGABIOS after re sume from S3.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 73 Power Manageme nt Controls ( Continue ) Setting Description Note Disabled Defa ult HDD Power Down 1-15Min When the set time has elapsed, BIOS sends a command to the HDD to power down. This turns of f the HDD moto r .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 74 Reload Global T imer Eve nt s Setting Desc ription Note Disabled Def aul t IDE0, IDE1 Primary Secondary Enabled In ef fect, the system remains alert for anything which occurs to a devic e which is configur ed as Enabled .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 75 3-7 PNP/PCI CONFIGUR A TION SETUP This option se ts the Moth erboard's P CI configurat ion. Phoenix – A ward BIOS CMOS Setup Utili ty PnP/PC I .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 76 PNP/PCI Config ur ation Co ntrol s Setting Descript ion Note Disabled Retain PnP con figuration data in BIOS . Default Rese t Conf igu rat ion Data Enabled Reset PnP configur ation dat a in BIOS. Manual BI OS does not manage PCI/ ISA P nP card IR Q ass ign ment.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 77 PNP/PCI Config uratio n Setup (Continued) Setting Descript ion Note How to set the BIOS to r elease the IRQ to the PnP Interrupt pool : Interrupt Line.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 78 3-8 PC HEAL TH ST A T US This option sets the Mother board's PC Health Status. Phoenix – A ward BIOS CMOS Setup Utili ty PC Health Stat us CPU Vcore 1.72 V Item Help +3.3V 3.21 V +5V 5.02 V +12V 1 1 .
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 79 3-9 LOAD F AIL-SAFE DEF AUL TS Select the [Load Fail-S afe Defa ults] opti on from t he Main Menu t o load a pre-defined safe bios se ttings.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 80 3-10 LOAD OPTI MIZED DEF AUL TS Selec t the [ Load O ptimize d Defau lts] o ption from the M ain Me nu to lo ad the pre- defined opt imized BIOS se ttings.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 81 3-11 SUPER VISOR P ASSWORD Based on the set ting you have made in t he [Secur it y Option] of the [Advan ced BIOS Feature] s ection, the password p revents access to the system or th e setup progr am by unauthor i zed user s.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 82 3. Enter your new pa ssword and pre ss [Enter]. The following message appears, prompt ing to confi rm the new pa ssword: 4.
BIOS Setup Utility SY - P4I865PE Plus DRAGON 2 83 Boot Men u Boot Me nu enables user to boot-up on diff ere nt boot device wi thou t going into the BIOS setup.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 84 Chapter 4 DRIVER S INST ALLA TIO N The S OYO- CD wil l Auto Ru n onl y in Windows Bas ed Op erati ng Systems. Y our SY -P4I 865PE Plus DRAGON 2 Mo therboard comes with a CD-ROM label ed “SOYO CD”.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 85 The user's ma nual fil es i ncluded o n th e SOYO CD are in PDF (Postscript Document Format ). In order t o read a PDF fi le, the appr opriat e Acrobat Reader software must b e in stalled in your system.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 86 Step 2. Install Driver s and U tilitie s Highli ght the dr iver you wa nt to in st all and t hen cl ick ok. The Start Up program di splays t he dri vers avail able for the partic ular model of Motherboar d you own.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 87 C-MEDIA Audio Driver for Win 9x/ME/2000/NT/XP The driver support s 2/4/ 6 sp eakers 3D posi tional audio. P4I 865PE DRAGON 2 ha rdware mo nitor for Win 9x/ME/2000/NT/ XP Y our motherboard comes w ith a hardware monitoring IC .
Drivers insta llation SY - P4I865PE Plus DRAGON 2 88 After W indows XP installation, your de vice ma nager shoul d look l ike this:.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 89 After dri ver i nstall ation, your W indows XP device manager shoul d look like this: N ote: T o install the U SB 2.0 driver , p l eas e updat e t o W i ndows XP service pack 1. Check chapter 5 for more info.
Drivers insta llation SY - P4I865PE Plus DRAGON 2 90 Dri vers di re ctor y list in the CD dri ver.
Inte l USB 2.0 D river In stalla tion SY - P4I865PE Plus DRAGON 2 91 Chapter 5 INTEL USB 2.0 DRIVER I NST ALLA TION For Windows XP USB 2.0 drivers are available fo r do wnload usi ng Windows Update for Windows XP. For addition al information regard i ng USB 2.
Inte l USB 2.0 D river In stalla tion SY - P4I865PE Plus DRAGON 2 92 10.Choose [Se arc h for a suit ab le driver for my d evice]. 11.Cli ck [Next]. 12.Choose [Sp eci fy a l ocation ] un der "O ptiona l search locatio ns". 13.Cli ck [Next]. 14.
Ein wichtiger Punkt beim Kauf des Geräts AB Soft ATX 12V (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie AB Soft ATX 12V noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für AB Soft ATX 12V - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von AB Soft ATX 12V reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über AB Soft ATX 12V erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon AB Soft ATX 12V besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von AB Soft ATX 12V verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit AB Soft ATX 12V. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei AB Soft ATX 12V gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
