Benutzeranleitung / Produktwartung STUDIO 2 des Produzenten Krell Industries
Zur Seite of 20
STUDIO 2 O O 0 0 0 0 0 0 0 STUDIO 2 DIGITAL TO ANALOG PROCESSOR OWNER’S REFERENCE.
INTRODUCTION Thank you for your purchase of the Krell STUDIO 2 Digital-to- Analog Processor and welcome to the Krell family of audio components. Krell is dedicated to the development of technologi- cally advanced components for the reproduction of digitally recorded music.
....... TABL~ OF CONTENTS 4 UNPACKING INSTRUCTIONS 5 PLACEMENT 6 AC POWER CONSIDERATIONS 7 INPUT AND OUTPUT CONNECTIONS i i PROCESSOR OPERATION 13 OPERATING INSTRUCTIONS 15 QUESTIONS AND ANSWERS 18 SP.
UNPACKING UNPACKING INSTRUCTIONS 1. Open the box and remove the top layer of foam. The following items will now be visible: STUDIO 2 D/A Processor AC power cord Packet containing the Owner’s Reference and Warranty Card NOTE: If any of these items are not included, please contact your authorized dealer immediately for assistance.
PLACEMENT PLACEMENT Before you install the STUDIO 2 into your system, we recommend that you follow these guidelines in choosing the location. This will facilitate a clean, trouble-free installation. 1. Although well shielded, the STUDIO 2 should not be placed in close proximity to hum-sensitive components (i.
AC POWER AC POWER CONSIDERATIONS NOTE: While the STUDIO 2 has superb regulation and does not require a dedicated AC circuit, we strongly advise against any connections through extension cords or multiple AC adaptors. High quality 15 amp grounded AC strips are acceptable.
CONNECTIONS INPUT AND OUTPUT CONNECTIONS CAUTION: When making connections to this component or any other, make sure the power amplifier is OFF and the preamplifier is in the MUTE or STANDBY mode. 1. Connect the power cord to the back of the STUDIO 2 and plug the unit into the wall AC receptacle.
CONNECTIONS 3. The Left and Right channel RCA outputs are labeled on the back panel. The balanced outputs are not labeled. The balanced connector closest to the Left RCA output is for the left channel output and the connector closest to the RCA right output is the right balanced output.
CONNECTIONS 5. Once you have completed the necessary input and output connections, select the input of your choice. For each input selected, the corresponding LED will illuminate. When a powered digital input source and the Processor have linked, the SYNC LED will illuminate.
CONNECTIONS How to connect AT&T cables: a. Remove the plastic cover from the outside of the AT&T transmitter (located on Transport) and receiver (located on Pro- eessor). b. Locate the slot on the top of the AT&T receptacle. e. Locate the key on the top of the AT&T cable.
OPERATION INPUT SELECT SWITCHING The STUDIO 2 has multiple digital inputs. Each input has its own input switch and direct path to the digital Processor.
OPERATION 0 ° and 180 ° PHASE SWITCHING The absolute output phase of the STUDIO 2 can be changed. In some recordings the master tape was recorded out of phase, creating unusually poor sounding recordings. The STUDIO 2 can shift the absolute output phase 180 ° to correct for this anomaly.
OPERATION OPERATING INSTRUCTIONS 1. Select an input with the Input switch. Notice the Signal LED will illuminate when the digital source is turned on and has linked with the Processor. Once this link is complete, the Processor is ready to pass a signal.
OPERATION ’ " ’" NOTE: While your STUDIO 2 will perform beautifully from the moment you turn it on, it requires a minimum warm-up period of 8 hours before it begins to show its strongest sonic qualities. It will continue to improve over time.
QUESTIONS AND ANSWERS Q. My CD player has both fiber optic and coaxial outputs. Which one should I use? A. Given a choice, we prefer the AT&T optical link due to its ability to completely isolate the grounds between the digital source component and the Processor.
QUESTIONS AND ANSWERS Q. Do I have to switch the Sampling Frequency when I go between my CD and DAT? A. No. Your STUDIO 2 automatically senses the input frequency and does all necessary switching. Q. I am not getting any sound through the Processor. What could be wrong? A.
QUESTIONS AND ANSWERS Q. While listening to my STUDIO 2 I experience occasional periods of silence through my speakers. Is my Processor malfunc- tioning? A. Drop outs are caused by two primary reasons. First, drop outs can be caused by data corruption.
SPECIFICATIONS FREQUENCY RESPONSE -.3 dB@ 20KHz and at 8Hz SIGNAL TO NOISE > 115dB DIGITAL-TO-ANALOG CONVERTER 18 bit PROCESSING 1 Motorola DSP-56001 Upgradable software contained in socketed EPROM. LINEAt~TY + .3dB at -90dB THD +N .0025% -92dB CHANNEL SEPARATION >_ 109dB ANALOG OUTPUT VOLTAGE 2.
WARRANTY AND SERVICE WARRANTY AND SERVICE INFORMATION There are no user-serviceable parts inside the STUDIO 2. The STUDIO 2 has a limited warranty of five years parts and labor.
KRELL 35 Higgins Drive Milford CT 06460 SALES (203) 874-3139 FAX (203) 878-8373 © 1993 KRELL DIGITAL (STUDIO29303).
Ein wichtiger Punkt beim Kauf des Geräts Krell Industries STUDIO 2 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Krell Industries STUDIO 2 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Krell Industries STUDIO 2 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Krell Industries STUDIO 2 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Krell Industries STUDIO 2 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Krell Industries STUDIO 2 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Krell Industries STUDIO 2 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Krell Industries STUDIO 2. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Krell Industries STUDIO 2 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
