Benutzeranleitung / Produktwartung E2260SWDN des Produzenten AOC
Zur Seite of 60
E 22 60S W D N.
Safety ............................................................................................................................... ......................................... 4 National C onventio ns .............................................
EPEA T Declar ation ............................................................................................................. ............................. 5 6 Service ...............................................................................
Safety National Conventions The following subsections describe n otational conventions used in this document. Notes, Cautions, and W arnings Throughout this guide, blocks of text ma y be accompanied by an icon and printed in bold type or in italic type.
Power The monitor should be operat ed only from the type of power source indicat ed on the label. If you are not sure of the type of power supplied to your home, consu lt your dealer or local power company . The monitor is equipped with a three-pronged grounde d plug, a plug with a third (grounding) pin.
Inst allation Do not place the monitor on a n unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a person and cause serious damage to this product. Use onl y a cart, stand, tripod, bracket, or t able recommended by the manufacturer or sold with this product.
Cleaning Clean the cabinet regularly with cloth. Y ou can use soft-detergent to wipe out the stain, instead of strong-detergent which will cauterize the pro duct cabinet. When cleaning, make sure n o detergent is leaked into the product. The cleaning cloth should not be too rough as it will scratch the screen surface.
Other If the product is emitting a strange smell, sound or smoke, disconnect the po wer plug IMMEDIA TEL Y and contact a Service Center . Make sure that the ventilating ope nings are not blocked by a table or curtain. Do not engage the LCD monitor in severe vib ration or high impact conditions during operation.
Setup Content s in Box Not all signal cables (Audio,Analog, DVI ) will be provided for all countries and regions. Please check with the local dealer or AOC branch office for confirmation.
Setup S t and & Base Please setup or remove the base follo wing the steps as belo w . Setup: Remove: 10.
Adjusting V iewing Angle For optimal viewing it is recommended to look at the full fa ce of the monitor , then adjust the monitor's angle to your own preference. Hold the stand so you will not toppl e the moni tor when you change the mon itor's angle.
Connecting the Monitor Cable Connections In Back of Monitor an d Computer: 1. Power 2. Analo g (DB-15 VGA cable) T o protect equipment, al ways turn off the PC and LCD monitor before conn ecting. 1 Connect the power cable to the AC port on the back of the monitor .
W all Mounting Preparing to Install An Optional Wall Mounting Arm. This monitor can be attached to a wall mounting arm you p urchase separately . Disconnect power before this procedure. Follow these steps: 1 Rem ove the base. 2 F ollo w the manufacturer' s instructi ons to assemb le the wall mo unting arm.
Adjusting Setting Optimal Resolution Windows Vist a For Window s V ista: 1 Click ST ART . 2 Click CONTROL P ANEL. 3 Click Appearance and Personalization.
5 Click Display Settings. 6 Set the resolution SLIDE-BAR to 1 920 by 1080 . 15.
Windows XP For Windows XP: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Click Appearan ce and Themes. 5 Double click DISPLA Y . 16.
6 Click SETTINGS. 7 Set the resolution SLIDE-BAR to 1 920 by 1080 . Windows ME/2000 For Windows ME/2000: 1 Click ST ART . 2 Click SETTINGS. 3 Click CONTROL P ANEL. 4 Double click DISPLA Y . 5 Click SETTINGS. 6 Set the resolution SLIDE-BAR to 1 920 by 1080.
Hotkeys Power Press the Power button to turn on/off the monitor . Eco (DCR)/ < Press the Eco key to select the Eco m ode of brightness and D CR on when there is no OSD.
OSD Setting Basic and simple instruction on the control keys. 1) Press the MENU-button to activate the OSD window . 2) Press <or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it .
Luminance 1 Press (Menu) to display menu. 2 Press <or > to select (Luminance), and pre ss to enter. 3 Press < or > to select submenu, and pre ss to enter.
4 Press < or > to adjust. 5 Press to exit . Brightness 0-100 Backlight Adju stment Contrast 0-100 Contra st from Digital-register. Eco mode Standard Standard Mode Tex t Text Mode Internet Intern.
Image Setup 1 Press (Menu) to display menu. 2 Press < or > to select (Image Setup), and press to enter. 3 Press <or > to select submenu, and press to enter.
Press < or > to adjust. 5 Press to exit . Clock 0-100 Adjust picture Clock to reduce Vertical-Line nois e. Phase 0-100 Adjust Picture Phas e to reduce Horiz ontal-Line noise Sharpness 0-100 Adjust picture sharpness H.Position 0-100 Adjust the hori zontal position of the picture.
Color Setup 1 Press (Menu) to display menu. 2 Press < or >to select (Color Setup), and pr ess to enter . 3 Press < or > to select submenu, and press to enter.
Press < or > to adjust. 5 Press to exit . Color setup. Warm Recall Warm Color Temperature from EEPROM. Normal Recall Normal Color Temperature from EEPROM. Cool Recall Cool Color Temperature from EEPROM. sRGB Recall SRGB Color Temperature from EEPROM.
Picture Boost 1 Press (Menu) to display menu. 2 Press < or > to select (Picture Boost), and press to enter . 3 Press < or > to select submenu, and press to enter.
4 Press < or > to adjust. 5 Press to exit . Frame Size 14-100 Adjust Frame Size Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast H.
OSD Setup 1 Press (Menu) to display menu. 2 Press < or > to select (OSD Setup), and press to enter . 3 Press < or > to select submenu, and pre ss to enter.
4 Press < or > to adjust. 5 Press to exit . H.Position 0-100 Adjust the h orizontal posit ion of OSD V.Position 0-100 Adjust t he verti cal position of OSD Timeout 5-120 Adjust the OSD Timeout T.
Extra 1 Press (Menu) to display menu. 2 Press < or > to select (Extra), and press to enter . 3 Press < or > to select submenu, and pre ss to enter.
4 Press < or > to adjust. 5 Press to exit . 31.
Input Select Auto /Analog Select Input Signal Sour ce Auto Config yes or no Auto adjust the picture to default Off timer 0-24hrs Select DC off time Image Ratio wide or 4:3 Select wide or 4:3 format fo.
Exit 1 Press (Menu) to display menu. 2 Press < or > to select (Exit), and press to exit . Exit Exit the main OSD 33.
LED Indicator Stat us LED Color Full Power Mode Active-off Mode Orange 34 Green.
Driver Monitor Driver Windows 7 1.S tart Windows® 7 2.Click on the 'St art' button and then click o n 'Control Panel'. 3. Click on the 'Display' icon.
4.Ckick on the “Change display settings ” button. 5. Click the “ Advanced Settings” button. 6. Click the “Monitor” tab and then click the “Properties” button.
7.Click the “Driver” tab. 8. Open the "Update Driver Soft ware-Generic PnP Monitor" window by clicking on “Update Driver... “ and then click the "Browse my computer for driver software" button. 9. Select "Let me pick from a list of device driv ers on my computer " .
10. Click the “Have Disk” button. Click on the “Brow se” button and navigate to the follo wing directory: X:Drivermodule name (where X is the drive letter desi gnator for the CD-ROM drive). 11. Select the "xxx.inf" file and click the “Open” button.
Windows Vist a 1. Click "S tart " and "Control Pane l". Then, doubl e-click on "Appearance and Personaliz ation". 2. Click "Personalization" and then "Display Settings". 3. Click "Advanced Settings.
4. Click "Prope rties" in the "Monitor" t ab. If th e "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below , click "Continue".
Windows XP 1. S tart Window s® XP 2. Click on the 'S tart' button and t hen click on 'Control Panel'. 3. Select and click on the categor y ‘Appearance and Themes’ 4.
5. Select the 'Settings' tab then click on the 'Advanced' butt on. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your m onitor is properly configur ed. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button.
8. Select the 'Install from a list or specific location [ advanced]' radio button and then click on the 'Next' button. 9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.
Windows 2000 1. S tart Windows® 2000 2. Click on the 'S tart' button, point to 'S ettings', and then click on 'Control Panel' . 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced.
i-Menu Welcome to “i-Menu” software by AOC. i-Menu makes it easy to adjust your monitor d isplay setting by using on screen menus instead of the OSD button on the monitor .
e-Saver Welcome to use AOC e-Saver monitor po wer management software! The AOC e-Saver features Smart Shutdo wn functions for your monitors, allows your monitor to timely shutdown when PC unit is at any status (On, Off, Sleep or Screen Saver); the actual shutdown time depends on your preferences (see example below).
Screen+ Welcome to "Screen+" software by AOC, Screen+ software is a desktop screen splitting tool, it splits the desktop into different panes, each pane displays a different window . Y ou only need to drag the window to a corresponding pane, when you want to access it.
T roubleshoot Problem & Question Possible Solutions Power LED Is Not ON Make sure th e power button is ON and the P ower Cord is pr operly connected to a grounded power outlet and to the monitor . No images on the screen Is the power cord connected properly? Check the power cord connection and po wer supply .
Monitor Is Stu ck In A ctive Off-Mode" The Computer Power Switch should be in the ON position. The Computer Video Card should be snugly fitted in its slot. Make sure the monitor's video cable is prop erly connected to the computer . Inspect the monitor's video cable and mak e sure no pin is bent.
S pecification General S pecification Panel Model name Driving system TFT Color LCD Viewable Image Size 54.7 cm diagonal Pixel pitch 0 .0 8 27 *RGB (H) mm x 0. 2 48 (V) mm Video Separate Sy nc. H/V TTL Display Color 16.7M Colors Dot Clock 1 44 MHz Resolution Horizontal scan range 30 kHz - 83 kHz Horizontal scan Size(Maximum) 4 76 .
A ltitude: Operating 0~ 3658m (0~ 12000 ft ) Non-Operating 0~ 12192m (0~ 40000 ft ) Preset Display Modes 51 Pin Assignment s ST ANDARD RESOLUTION HORIZONT AL FREQUENCY(kHZ) V ERTICAL FREQUENCY(Hz) V G A 640x480@60H z 31.469 59.94 V G A 640x480@72H z 37.
Pin Number 15-Pin Side of the Signal Cabl e 1 Video-Red 2 Video-Green 3 Video-Blue 4 N.C. 5 Detect Cable 6 GND-R 7 GND-G 8 GND-B 9 +5V 10 Ground 11 N.C.
Regulation FCC Notice FCC Class B Radio Freq uency Interference St atement WA RNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
WEEE Declaration Disposal of W aste Equipment b y Users in Pr ivate Household in the Eur opean Union. This symbol on the product or on its packaging indicates t hat this product must not be di sposed of with your other household waste.
5 5 WEEE /E-Waste declaration for India This symbol on the product or on its packaging indicates t hat this product must not be di sposed of with your other household waste.
EPEA T Declaration EPEA T is a system to help purchasers in the public an d private sectors evaluate, compare and select desktop computers, notebooks and monitors ba sed on their environmental attributes .
Service W arranty St atement for Europe 5 7 For AOC LCD Mo nitors sold wi thin Europe, AOC Int ernat ional (Europe) B.V. warrants this pro duct to be free from defects in material and workma nship for a period of Three (3) years after the original date of consumer purchase.
W arranty S t atement for North & South America (excluding Brazil) W ARRANTY ST A T EMENT for AOC Color Monitors Including those Sold within North America as S pecified Envision Peripherals, Inc.
ALL EXPRESS AND IMPLIED W ARRANTIES FOR THIS PRODUCT (INCLUDING THE W ARRANTIES OF MERCHANT ABILITY AND FITNESS FOR A P ARTICULAR PURPOSE) ARE LIMITED IN DURA T ION TO A PERIOD OF THREE (3) YEARS FOR P ARTS AND LABOR AND ONE (1) YEAR FOR CRT T UBE OR LCD P ANEL FROM THE ORIGINAL DA TE OF CONSUMER PURCHASE.
WARRANTY PERIOD COVERAGE AT NO CHARGE CUSTOMER CHARGES Within the first three months of purchase: Covered by EASE - New AOC monitor - Call tag dispatched and return freight charges via UPS - None* Bet.
Ein wichtiger Punkt beim Kauf des Geräts AOC E2260SWDN (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie AOC E2260SWDN noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für AOC E2260SWDN - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von AOC E2260SWDN reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über AOC E2260SWDN erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon AOC E2260SWDN besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von AOC E2260SWDN verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit AOC E2260SWDN. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei AOC E2260SWDN gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
