Benutzeranleitung / Produktwartung KHMS 105 des Produzenten KitchenAid
Zur Seite of 20
INSTALLATION INSTRUCTIONS. ’ KitchenAid@ 30” BUlLT4N MICRO WAVE/HOOD MODEL: KHMS 105 MICRO WAVE-CONVECTION HOOD MODEL: KHMC 106 Read And Save These Installation instructions.
-. INTRODUCTION Please read all instructions thoroughly before installing Microwave/Hood System. TWO PEOPLE are required to in-iall this product. If a new electrical outlet is required, it should be connected by a qualified electrician before the MicrowaveB-lood -1 is installed.
MOUNTING SPACE Microwave/Hood System requires mounting space on a wall as shown below. I BACKSPLASH ,30” OR MORE FROM COOKING SURFACE t- 66” OR MORE FROM FLOOR J For removal of the Microwave/Hood .
. WALL CONSTRUCTION Microwave/Hood System should be mounted against and supported by a flat, vertical wall: If wall is not flat, use spacers to fill gaps. Mounting plate must be flat for proper installation. Wall construction should be a minimum of 2” x 4” wood studding and 3/S” or more thick dry wall or plaster/lath.
. ELECTRICAL SERViCE Visual check after unpacking. Remove all packing material from the oven cavity. Check the oven for any damage, such as misaligned door, damaged ,gaskets around door or dents inside the oven cavity or on the door.
HOOD EXHAUST DUCT Outside ventilation requires HOOD EXHAUST DUCT. Read the following carefully. EXHAUST CONNECTION: The hood exhaust has been designed to mate with a standard 3-x” x 10” rectangular duct. If round duct is required, a rectangular-to-round transition adaptor must be used.
‘TOOLS RECOMMENDED FOR INSTALLATION Phillips Screw -Driver Electric Drill 5/8”, 3/32” Drill Bit l-1/2” Wood Bit Pencil Measure Tape Saw to cut exhaust opening (if needed) Protective drop cloth for product and range. You may use part of carton for protectim.
PREPARATION OF PRODUCT / Figure 1 3. Remove and save two hexagonal Philiips head screws (inside grease filter openings) (Fig. 2). HEXAGONAL PHILLIPS HEAD SCREW FRONT / SIDE REMOVING MOUNTING PLATE 1. Use a portion of the carton or some other material to protect the outercase from being damaged.
LOWER HOOKS SLIDERS Figure 3 LEVERS 4. Pull out two levers to release sliders from hooks. This action will release mounting plate from back surface of outercase. Familiarize yourself with the operation of the mountrng levers so you will be aware of the proper pro- cedure for mounting the unit to the wall.
VENTILATION SYSTEM .: MICROWAVE/HOOD SYSTEM IS DESIGNED FOR ADAPTATION TO THE FOLLOWING THREE (3) TYPES OF VENTILATION SYSTEMS. Select the type required for your installation. a. OUTSIDE VENTILATION: Vertical Exhaust b. OUTSIDE VENTILATION: Horizontal Exhaust c.
B. OUTSIDE VENTILATION: Horizontal Exhaust 1. Remove and save 9 screws. Remove rear stay (Fig. 5). 2. Withdraw hood fan unit carefully (Fig. 6). 3. Rotate hood fan unit ‘/4 turn (Fig.
4. Replace hood fan unit into oven unit with left corner side inserted into opening first, right corner next. Be careful -not to pinch the lead wire between the back plate and hood fan unit (Fig. 8). Figure 8 5. Replace the rear stay. First, attach rear stay to unit with 2 screws (Fig.
t. RECIRCULATING: Non-Vented, Ductless I. Remove and save 9 screws. Remove rear stay. (Fig. 5 pg. 11). 2. Withdraw hood fan unit. (Fig. 6 pg. 11). 3. Change lead wire holding position from left side wire retainer to right side wire retainer (Fig. 11).
PREPARATION OF WALL AND TOP CABINET MOUNTING TEMPLATES I’ CAUTION: THIS PRODUCT CANNOT BE PROPERLY INSTALLED WITHOUT REFERRING TO MOUNTING INSTRUCTIONS ON BOTH TEMPLATES. Read and follow mounting information on both Top Cabinet and Wall Templates. Templates are included in the printed matters packed witlithis oven.
-MOUNTING PLATE INSTALLATION 1. Separate toggle bolts from toggle nuts. 2. Insert one toggle bolt into each hole on the mounting plate (these holes correspond to holes A, B, C and D of the Wall Template) and put toggle nut onto the toggle bolt (Fig. 13).
PRODUCT INSTALLATION 1. Place Styrofoam packing blocks (2 pieces) on top surface of range/cooktop Figure 16 2. Place microwave/hood system on top of Styrofoam blocks as shown in Fig. 16. 3. Thread power supply cord through the hole at the bottom of top cabinet.
7. Check to be sure the unit is secure to the mounting plate at both upper and lower hooks when you remove your support. 8. Screw hexagonal Phillips head screws to levers (inside grease filter opening) (Fig. 18). Figure 18 9. Check that both levers (a) are securely fixed.
10. Use adjusting screws fc) and flat washers (d) for gaps between top cabinet and unit (Fig. 19). Id) Figure 19 11:Make a bundle of power supply cord, then fix it to cabinet using cord hook A short power supply cord is provided to reduce the risks resulting from contacting the cooking sur- face or from becoming tangled.
. CHECK LIST FOR INSTALLATION 1. Make sure unit has been installed according to instructions 2. Remove all packing material from the oven. 3. Plug in power cord. 4. Read Use and Care Manual. 5. Keep installation instructions for the local electrical inspector’s use.
km MS032 KitchenAid, Inc. St. Joseph, MI 49085 (f/74735.
Ein wichtiger Punkt beim Kauf des Geräts KitchenAid KHMS 105 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie KitchenAid KHMS 105 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für KitchenAid KHMS 105 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von KitchenAid KHMS 105 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über KitchenAid KHMS 105 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon KitchenAid KHMS 105 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von KitchenAid KHMS 105 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit KitchenAid KHMS 105. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei KitchenAid KHMS 105 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
