Benutzeranleitung / Produktwartung KRC-666G des Produzenten Kenwood
Zur Seite of 42
KRC-766 KRC-666R KRC-666G KRC-666 ©B64-2526- 1 0/0 1 (MW) CASSETTE RECEIVER INSTRUCTION MANUAL KRC-766(M)_Cover_r1 02.11.11 7:55 PM Page 1.
— 2 — English Contents Safety precautions .........................3 About Cassette tape ......................4 General features .................
— 3 — To prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery , or ground wires, make sure to use automotive- grade wires or other wires with a 0.
— 4 — English • If you experience problems during installation, consult your Kenwood dealer . • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer .
Increasing V olume Tu rn the [VOL] knob clockwise. Decreasing V olume Tu rn the [VOL] knob counterclockwise. V olume Press the [SRC] button. Source required Display T uner "TUNER" T ape &quo.
Fine-tuning so that the System Q value is optimal when setting the speaker type. 1 Enter Standby Press the [SRC] button. Select the "ALL OFF" display . 2 Enter Speaker Setting mode Press the [System Q] button. 3 Select the Speaker type Press the [ 4 ] or [ ¢ ] button.
In T ape source KRC-766 : Information Play side Play side & T ape counter Play side & T ape running Clock KRC-666R/666/666G: Information Play side T ape running & T ape counter T ape runni.
Selecting the display when this device is switched to Auxiliary input source. 1 Select Auxiliary input source Press the [SRC] button. Select the "AUX1" display . 2 Enter Auxiliary input display setting mode Press the [NAME.S] button for at least 2 seconds.
Function of the KRC-666R The audio system automatically mutes when a call comes in. When a call comes in "CALL" is displayed. The audio system pauses. Listening to the audio during a call Press the [SRC] button. The "CALL" display disappears and the audio system comes back ON.
Entering the frequency and tuning. 1 Select the band Press the [FM] or [AM] button. 2 Enter Direct Access T uning mode Press the [DIRECT] button on the remote. "– – – –" is displayed. 3 Enter the frequency Press the number buttons on the remote.
Calling up the stations in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Call up the station Press the desired [1] — [6] button. Preset T uning • When Auto Memory Entry is done in the FM2 band, the RDS stations preset in the FM1 band aren't put in the memory .
Selecting the Program T ype and searching for a station. 1 Enter PTY mode PTY (Program T ype) Scrolling the displayed radio text. Press the [DISP] button for at least 1 second. Radio T ext Scroll Switching to traffic information automatically when a traffic bulletin starts even when you aren't listening to the radio.
25. Leisure "LEISURE" 26. Jazz Music "JAZZ" 27. Country Music "COUNTRY" 28. National Music "NA TION M" 29. Oldies Music "OLDIES" 30. Folk Music "FOLK M" 31. Documentary "DOCUMENT" • Speech and Music include the Program type shown below .
Language Display English "ENGLISH" French "FRENCH" Swedish "SWEDISH" German "GERMAN" 4 Exit Changing Language mode Press the [DISP] button. Selecting the Program T ype display language. 1 Enter PTY mode Refer to <PTY (Program T ype)> (page 12).
Selecting the station. 1 Select tuner source Press the [SRC] button. Select the "TUNER" display . 2 Select the band Press the [FM] or [AM] button. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. 3 T une up or down band Press the [ 4 ] or [ ¢ ] button.
Changing the tuning frequency step. The original setting is FM band 50 kHz, and AM band 9 kHz. While pressing the [1] and [5] button, press the Reset button. The frequency step changes to FM band 200 kHz, and AM band 10 kHz. • When the same operation is repeated, it returns to the original setting.
Cassette player features — 17 — B.S B NR PRO MTL REP ¢4 SRC FM AM KRC-766 KRC-666R/666/666G IN indicator IN indicator Release button KRC-766(M)_U.
Press the [MTL] button. Each time the button is pressed the T ape type switches as shown below . Selecting the T ape type Press the [B NR] button. Each time the button is pressed the Dolby B NR turns ON or OFF . When it's ON, "B-NR" is displayed.
Repeating the present song. Press the [REP] button. Each time the button is pressed the Music Repeat turns ON or OFF . When it's ON, "Repeat ON"/ "REP ON" is displayed. Music Repeat Fast forwarding automatically when an unrecorded portion continues for at least 10 seconds.
Selecting the song you want to hear . Press the [ 4 ] or [ ¢ ] button. Tr ack Search Fast Forwarding Hold down on the [ ¢ ] button. Release your finger to play the disc at that point. Reversing Hold down on the [ 4 ] button. Release your finger to play the disc at that point.
Playing all the songs on the disc in random order . Press the [RDM] button. Each time the button is pressed Random Play turns ON or OFF . When it's ON, "Random ON"/ "RDM ON" is displayed. When the [ ¢ ] button is pressed, the next song select starts.
Canceling the DNPP mode Press the [DNPP] button on the remote. Function of the KRC-766/KRC-666R/KRC-666 Selecting the CD displayed in the DNPS of the CDs set in the Disc changer . 1 Enter DNPP mode Press the [DNPP] button on the remote. When "DNPP" is displayed the DNPS display in order .
Setting during operation beep sound etc. functions. The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation. 1 Enter Menu mode Press the [MENU] button for at least 1 second.
This adjustment can be done when the <Synchronize Clock> (page 25) is set as OFF . (KRC-666R only) Manual Clock Adjustment Setting the operation check sound (beep sound) ON/OFF . Display Setting "Beep ON"/ "BEEP ON" Beep is heard.
Adjusting the display contrast. Display and Setting "Contrast 0"/ "CONT 0" "Contrast 10"/ "CONT 7" … Contrast Adjustment Setting the Display type. Display Setting "Display C"/ "DISP C" Demonstration.
Function of the KRC-766/KRC-666/KRC-666G T emporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station.
Function of the KRC-666R Noise can be reduced when stereo broadcasts are received as monaural. Display Setting "MONO OFF" The monaural reception is OFF .
Accessory of the KRC-766/KRC-666R/KRC-666 Basic Operations of remote Function of the KRC-666R Setting the displayed text scroll. Display Setting "SCL MANU" Doesn't scroll. "SCL AUTO" Scrolls when the display changes. The text scrolled is shown below .
[FM]/ [AM] buttons Select the band. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. [ 4 ]/ [ ¢ ] buttons T une up or down band. [0] — [9] buttons Press buttons [1] — [6] to recall preset stations. [DIRECT] button Enters and cancels the <Direct Access T uning> (page 10) mode.
[0] — [9] buttons When in <Direct T rack Search> (page 21) and <Direct Disc Search> (page 21), enter the track/disc number . [ 4 ]/ [ ¢ ] buttons Doing track forward and backward. [DISC+]/ [DISC–] buttons Doing disc forward and backward.
— 31 — — 31 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery .
English — 32 — — 32 — Connecting Wires to T erminals (KRC-766/666/666G) P.CONT ANT. CONT. FRONT • L FRONT • R REAR • L REAR • R – + FRONT FM/AM antenna input 1 Fuse (10A) 24 KENWOOD .
— 33 — — 33 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery .
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 TEL MUTE P.CONT ANT.CONT English — 34 — — 34 — Connecting Wires to T erminals (KRC-666R) Rear right output (Red) 4 Rear left output (White) Connector Function G.
— 35 — ■ Installation Connecting Wires to T erminals (KRC-666R) Connecting the ISO Connector The pin arrangement for the ISO connectors depends on the type of vehicle you drive. Make sure to make the proper connections to prevent damage to the unit.
English — 36 — — 36 — 8 mm MAX. ø5mm ø5mm 8mm MAX. ■ Installing in Japanese-Made Cars T: T oyota cars N: Nissan cars T N N T T/N Accessory 3 ...for Nissan car Accessory 4 ...for T oyota car • During installation, do not use any screws except for those provided.
— 37 — — 37 — Accessory 2 Removal tool Screw (M4X8) (commercially available) ■ Removing the Unit 4 Lower the removal tool toward the bottom, and pull out the unit halfway while pressing towards the inside. Be careful to avoid injury from the catch pins on the removal tool.
English — 38 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. 01 ✔ The fuse has blown.
— 39 — Cassette tape source ? Can’ t remove tape. 44 ✔ The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF . ☞ The tape can only be removed within 10 minutes of the ACC switch being turned OFF . If more than 10 minutes has elapsed, turn the ACC switch ON again and press the Eject button.
English — 40 — T roubleshooting Guide The messages shown below display your systems condition. EJECT : No disc magazine has been loaded in the changer . The disc magazine is not completely loaded. E01 ➪ Load the disc magazine properly . No Disc/ NO DISC: No disc has been loaded in the disc magazine.
— 41 — Specifications FM tuner section (KRC-766/ KRC-666/ KRC-666G) Frequency range (50 kHz space) .................................87.5 MHz –108.0 MHz (200 kHz space) ...............................87.9 MHz –107.9 MHz Usable sensitivity (S/N = 30dB) .
KRC-766(M)_ Eng _r 3 Page 4 2.
Ein wichtiger Punkt beim Kauf des Geräts Kenwood KRC-666G (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Kenwood KRC-666G noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Kenwood KRC-666G - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Kenwood KRC-666G reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Kenwood KRC-666G erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Kenwood KRC-666G besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Kenwood KRC-666G verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Kenwood KRC-666G. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Kenwood KRC-666G gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
