Benutzeranleitung / Produktwartung KDC-MP4026V des Produzenten Kenwood
Zur Seite of 32
KDC-MP4026V CD-RECEIVER INSTR UCTION MANU AL © B64-2687-00/01 (MW) B64-2687-00_U.S_r3.5.Indd 1 03.11.28, 9:29:12 AM.
2 | English Con t ents Sa fe ty precautions 3 Notes 5 Notes on playing MP3/WMA 6 Abo ut CDs 8 G eneral fea tures 9 Pow er Selecting the Source Volume Attenuator Loudness System Q A udio Control Speake.
English | 3 Sa fe ty precautions 2 CA UTION To pre vent damage to the machine, tak e the following precautions: • Make sure to gr ound the unit to a negative 12V DC power supply . • Do not open the top or bottom cov ers of the unit. • Do not install the unit in a spot exposed to dir ect sunlight or excessive heat or humidity .
4 | English Sa fe ty precautions NO TE • If you experience problems during installation, consult your Kenwood dealer . • If the unit fails to operate properly , press the Reset button. The unit returns to factory settings when the Reset button is pressed.
English | 5 Notes Cleaning the Unit If the faceplate of this unit is stained, wipe it with a dry sof t cloth such as a silicon cloth. If the faceplate is stained badly , wipe the stain off with a cloth moistened with neutral cleaner , then wipe neutral detergent off .
6 | English Notes on playing MP3/WMA KDC-MP4026V can play MP3(MPEG1, 2 Audio Layer 3)/WMA. Not e, however , that the MP3/WMA r ecording media and f ormats acceptable are limited. When writing MP3/WMA, pay attention to the following restrictions. A cc eptable media The MP3/WMA recor ding media acceptable to this unit are CD-ROM, CD-R, and CD -RW.
English | 7 MP3/WMA playing order When selected for play , F older Search, File Sear ch, or for F older Select, files and folders are accessed in the order in which they were written by the CD writer . Because of this, the order in which they ar e expected to be played may not match the or der in which they are actually played.
8 | English Handling CDs • Don ’t touch the recor ding sur face of the CD . • CD-R and CD-R W are easier to damage than a normal music CD. Use a CD-R or a CD-R W after r eading the caution items on the package etc. • Don ’t stick tape etc. on the CD .
English | 9 G eneral f eatures Powe r Tu rning ON the Pow er Pr ess the [SRC] button. Tu rning OFF the Pow er Pr ess the [SRC] button for at least 1 second.
10 | English G eneral f eatures Lo udness C ompensating for low and high t ones during low volume. Pr ess the [L OUD] button for at least 1 sec ond. Each time the button is pressed f or at least 1 second the Loudness turns ON or OFF . When it's ON, "L OUD" indicator is ON.
English | 11 Sw itching Display S witching the information displa yed. Pr ess the [DISP] button. Each time the button is pressed the display switches as shown below .
12 | English G eneral f eatures Sta tion/Disc Naming (SNPS/DNPS) A ttaching a title to a Station or a CD of the CD Changer . 1 Receive/pla y the station/disc you want to a ttach a title to • A title can't be attached to MD or MP3/WMA media. • Y ou cannot use the Disc Naming for the built-in CD player .
English | 13 T uner featur es Tu ning Mode Choose the tuning mode. Pr ess the [A UTO ] button. Each time the button is pressed the Tuning mode switches as shown below . T uning mode Display Operation Au to seek " AUT O 1" indicator Aut omatic search for a station.
14 | English T uner featur es Au to Memory Entr y P utting stations with good reception in the memory automatically. 1 S elect the band for Auto Memory Entry Pr ess the [FM] or [AM] butt on. 2 Open Auto Memory Entry Pr ess the [AME] button for a t least 2 seconds.
English | 15 Playing CD & MP3/WMA & VCD W hen a CD is inserted Pr ess the [SRC] button. Select the "CD" display. • When a CD is inserted, the "IN" indicator is ON. E ject the CD Pr ess the [ 0 ] button. • 3 in. (8cm) CD cannot be played.
16 | English CD/MP3/WMA/VCD/External disc control f eatures Fa st F or war ding and Reversing F ast Forwarding Hold down on the [ ¢ ] button. Release your finger to play the disc at that point. Reversing Hold down on the [ 4 ] button. Release your finger to play the disc at that point.
English | 17 F unction of disc changer Magazine Random Play Play the songs on all the discs in the disc changer in random order . Pr ess the [M.RDM] button. Each time the button is pressed the Magazine R andom Play turns ON or OFF . When it's ON, "MRDM ON" is displayed .
18 | English Menu system Menu Sy stem S etting during operation beep sound etc. functions. T he Menu system basic operation method is explained here. The reference f or the Menu items and their setting content is after this operation explanation. 1 Enter Menu mode Pr ess the [MENU] button for at least 1 second .
English | 19 Manual Clock Adjustment 1 S elect Clock Adjustment mode Pr ess the [FM] or [AM] butt on. Select the "CLK ADJ" display. 2 Enter Clock Adjust mode Pr ess the [ 4 ] or [ ¢ ] button for at least 2 seconds. The clock display blinks.
20 | English Menu system Te x t Scr oll S etting the displayed text scroll. Display Setting "SCL AUT O" Repeats scroll . "SCL MANU" Scrolls when the display changes .
English | 21 Basic Operations of r emote Lo ading and Replacing the battery U se two " AA "-size batteries. Slide the cover while pr essing downwards to r emove it as illustrated . I nsert the batteries with the + and – poles aligned properly , following the illustration inside the case .
22 | English Basic Operations of r emote In T uner source [FM]/ [ AM] buttons Select the band. Each time the [FM] button is pr essed it switches between the FM1, F M2, and FM3 bands. [ 4 ]/ [ ¢ ] buttons T une up or down band. [0] — [9] buttons Pr ess buttons [1] — [6] to recall preset stations .
English | 23 A cc essories/ Installa tion Procedur e A cce ssories 1 ..........1 2 ..........2 3 ..........4 4 ..........4 5 ..........1 6 ..........1 7 ..........1 Installation Proc edure 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - batter y .
24 | English C onnecting W ires to T erminals ANT. CONT TEL MUTE P.CONT FRONT • L FRONT • R REA R•L REAR • R – + AUX VIDEO OUT PRK SW Battery Ground wire (Black) - (T o car chassis) F M/AM a.
English | 25 Installation • Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). non-Japanese cars Ja panese cars 1 Refer to the section 'Removing the hard rubber frame' (page 27) and then remove the hard rubber frame.
26 | English Installation Sc rew ing the F aceplate on the Unit If y ou want to fasten the fac eplate to the main unit so that it does not fall off , screw in the provided screw in the holes sho wn below. Accessory 5 • Never insert the screw in any other screw hole than the one specified.
English | 27 Removing the Unit Removing the hard rubber fr ame 1 Engage the catch pins on the removal tool and r emove the two locks on the upper level . Upper the frame and pull it forward as shown in the figure. 2 When the upper level is removed , remove the lower two locations.
28 | English Tr oubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Befor e calling ser vice , first check the f ollowing table f or possible problems. G eneral ? T he pow er does not turn ON.
English | 29 MP3/WMA source ? C annot play an MP3/WMA. ✔ The media is scratched or dirty. ☞ Clean the media, referring to the CD cleaning of the section on ' About CDs' (page 8). ? T he sound skips when an MP3/WMA is being played . ✔ The media is scratched or dirty.
30 | English T he messages shown below displa y your systems condition. EJ ECT: No disc magazine has been loaded in the changer . The disc magazine is not completely loaded. ➪ L oad the disc magazine properly . No CD in the unit. ➪ I nser t the CD .
English | 31 Specifications FM tuner section Fr equenc y range (50 kHz space): 87.5 MH z – 108.0 MHz (200 kHz space): 87.9 MH z – 107.9 MHz Usable sensitivity (S/N = 30dB) : 9.
B64-2687-00_U.S_r3.5.Indd 32 03.11.28, 9:31:21 AM.
Ein wichtiger Punkt beim Kauf des Geräts Kenwood KDC-MP4026V (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Kenwood KDC-MP4026V noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Kenwood KDC-MP4026V - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Kenwood KDC-MP4026V reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Kenwood KDC-MP4026V erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Kenwood KDC-MP4026V besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Kenwood KDC-MP4026V verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Kenwood KDC-MP4026V. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Kenwood KDC-MP4026V gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
