Benutzeranleitung / Produktwartung KDC-8023 des Produzenten Kenwood
Zur Seite of 42
KDC-8023 © B64-2463-00/01 (MV) CD-RECEIVER INSTR UCTION MANU AL COMPACT DIGITAL AUDIO KDC-8023(M) Cover_r2 03.1.8 3:44 PM Page 1.
— 2 — English Contents Safety precautions.............................3 About CDs ..........................................5 About GSM Hand Free Unit ...............5 Notes on Multi-function Key System .....................................6 General features .
— 3 — Safety precautions To prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery , or ground wires, make sure to use automotive- grade wires or other wires with a 0.
— 4 — English Safety precautions • If you experience problems during installation, consult your Kenwood dealer . • If the unit fails to operate properly , press the Reset button. The unit returns to factory settings when the Reset button is pressed.
— 5 — About CDs Handling CDs • Don’t touch the recording surface of the CD. • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. • Don’t stick tape etc. on the CD.
— 6 — English Notes on Multi-function Key System Multi-function Key System serves to control various functions with the [2] — [5] buttons. The basic operation of the Multi-function Key System is described below .
Press the [SRC] button. Source required Display T uner "TUNER" CD "CD" TV (Optional accessory) "TV" External disc (Optional accessory) "DISC CH" Auxiliary input.
1 Select the source for adjustment Press the [SRC] button. 2 Select the key function section Press the [NEXT] button. Repeatedly press the button until "AUD" is displayed above the [2] button. Refer to <Notes on Multi-function Key System> (page 6).
[3] button Adjustment Item Display Range Middle level "Middle" –8 — +8 [4] button Adjustment Item Display Range Tr eble level "T reble" –8 — +8 [5] button Adjustment Item D.
Switching the display mode. 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "DISP" is displayed above the [3] button. Refer to <Notes on Multi-function Key System> (page 6). Display Mode Switching Fine-tuning so that the System Q value is optimal when setting the speaker type.
2 Enter display control mode Press the [3] ("DISP") button. 3 Select the display mode Press the [2] ("MODE") button. Each time the button is pressed the display mode switches as shown below . Display Display Mode "Display C" Demonstration.
In Standby Information Display "ALL OFF" Clock "Clock" 4 Exit Display Control mode Press the [RTN] button. If the Disc title or T rack title is selected when the disc which does not have disc title or track title is played, track number and play time are displayed.
7 Exit name set mode Press the [NAME.S] button. • When operation stops for 10 seconds the name at that time is registered, and Name Set mode closes. • Memory numbers - FM: 32 stations - AM: 16 stations - Internal CD player: 30 discs - External CD changer/ player: V aries according to the CD changer/ player .
Setting the angle or back-forward position of the control panel. 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "PNL" is displayed above the [4] button. 2 Enter Panel Position Setting mode Press the [4] ("PNL") button.
Prevents tampering with the unit while your car is being serviced etc. Hiding the control panel Press the [SRC] button for at least 1 second. When the time set in <OFF Wait T ime Setting> (page 30) lapses, the panel is hidden and the power turns OFF .
5 Exit the Dual Zone System Control mode Press the [RTN] button. 6 Select the source Press the [SRC] button. Select the source sound to be output from the internal source channel.
Selecting the station. 1 Select tuner source Press the [SRC] button. Select the "TUNER" display . 2 Select the band Press the [FM] or [AM] button. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. 3 T une up or down band Press the [ 4 ] or [ ¢ ] button.
Changing the tuning frequency step. Frequency Step Setting Calling up the stations in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Select the key function section Press the [NEXT] button. Repeatedly press the button until the function item is not displayed above the [2] — [5] button.
2 Select the key function section Press the [NEXT] button. Repeatedly press the button until the function item is not displayed above the [2] — [5] button. Refer to <Notes on Multi-function Key System> (page 6). 3 Call up the TV channel Press the desired [1] — [6] button.
When there is no disc inserted 1 Open the panel to insert disc Press the [ 0 ] button. 2 Insert a disc. When the faceplate has been slid open, it might interfere with the shift lever or something else. If this happens, pay attention to safety and move the shift lever or take an appropriate action, then operate the unit.
Doing T rack Search by entering the track number . 1 Enter the track number Press the number buttons on the remote. 2 Do T rack Search Press the [ 4 ] or [ ¢ ] button. Canceling Direct T rack Search Press the [ 38 ] button. Direct T rack Search (Function of remote) Selecting the disc you want to hear .
Play all the songs on the disc folder in random order . 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "RDM" is displayed above the [3] button. 2 Tu rn ON/OFF the Random Play Press the [3] ("RDM") button.
Play the songs on all the discs in the disc changer in random order . 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "MRDM" is displayed above the [5] button. 2 Tu rning ON/OFF the Magazine Random Play Press the [5] ("MRDM") button.
Received calls can be answered when a GSM Hands Free Unit (optional accessory) is connected to this unit. 1 When a Call is Received "HF CALL" will be displayed. 2 Accept a call Press the [1], [3] — [6] or [NEXT] button. Switching between the Name and T elephone Number Press the [AUTO] button.
— 25 — Inputting the telephone number with number buttons on the remote, and dialing. 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "H-F" is displayed above the [2] button. Refer to <Notes on Multi-function Key System> (page 6).
Synchronizing the data in this unit with the data in the GSM telephone. 1 Select the key function section Press the [NEXT] button. Repeatedly press the button until "SYNC" is displayed above the [3] button. Refer to <Notes on Multi-function Key System> (page 6).
— 27 — Setting during operation beep sound etc. functions. The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation. 1 Enter Menu mode Press the [MENU] button for at least 1 second.
Selecting the speaker to output the Phone voice. Display Setting "HFSP ALL" Phone voice sent to the front and rear speaker . "HFSP FR" Phone voice send to the front right speaker . "HFSP FL" Phone voice sent to the front left speaker .
— 29 — A red indicator will blink on the unit after the faceplate is removed, warning potential thieves. Display Setting "DSI ON" LED flashes. "DSI OFF" LED OFF . DSI (Disabled System Indicator) 1 Select Clock Adjustment mode Press the [FM] or [AM] button.
Switching the preout between the rear and non-fading. (In non- fading it outputs without effect from the fader control.) Display Setting "SWPRE Rear" Rear preout.
— 31 — Set the Built-in Auxiliary Input function. Display Setting "AUX OFF" When selecting the source there's no Auxiliary Input. "AUX ON" When selecting the source there's Auxiliary Input. Built-in Auxiliary input Setting Setting the displayed text scroll.
— 32 — English [VOL.] buttons Adjusting the volume. [SRC] button Each time the button is pressed the source switches. For the source switching order refer to <Selecting the Source> (page 7). [A TT] button Tu rning the volume down quickly . When it is pressed again it returns to the previous level.
— 33 — [ 4 ]/ [ ¢ ] buttons Switching the display . [FM]/ [AM] buttons Switching the initials and messages. [0] — [9]/ [+]/ [#]/ [ * ] buttons When in <Direct Dial> (page 25), enter the telephone number . [] button Entering and switching the Hands Free mode.
English — 34 — .........2 Do not use any accessories other than those provided with your unit. If you use other accessories, you may damage the unit. 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery . 2.
ANT.CONT. ILLUMI EXT.CONT. P.CONT + + + + – + FRONT REAR AUX IN NON FADINFG FM/AM antenna input 15 Fuse (10A) 27 Wiring harness (Accessory 1 ) 22 28 White/Black 31 Gray/Black 34 Green/Black 37 Purpl.
Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.
— 37 — Removing the Unit Installation (Japanese-cars) Catch Lock Accessory 2 Removal tool ■ Removing the hard rubber frame 2 When the upper level is removed, remove the lower two locations. The frame can be removed from the bottom side in the same manner .
3 Reattach the Backpanel. Never insert the panel lock screws (M2 X 1.5 mm) in any other screw holes than the one specified. If you insert them in another hole, it will contract and may cause damage to the mechanical parts inside the unit.
— 39 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. 01 ✔ The fuse has blown.
English — 40 — Tr oubleshooting Guide A CD ejects as soon as it is loaded. 62 ✔ The CD is quite dirty . 63 ☞ Clean the CD, referring to the CD cleaning of the section on <About CDs> (page 5). ? Can’ t remove disc. 64 ✔ The cause is that more than 10 minutes has elapsed since the vehicle ACC switch was turned OFF .
— 41 — Hold Error: The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F), stopping all operation. E0d ➪ Cool down the unit by opening the windows or turning on the air conditioner .
English — 42 — Specifications FM tuner section Frequency range (50 kHz space) ..............87.5 MHz – 108.0 MHz (200 kHz space) ............87.9 MHz – 107.9 MHz Usable sensitivity (S/N = 30dB) .................. 9.3dBf (0.8 µV /75 Ω ) Quieting Sensitivity (S/N = 50dB) .
Ein wichtiger Punkt beim Kauf des Geräts Kenwood KDC-8023 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Kenwood KDC-8023 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Kenwood KDC-8023 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Kenwood KDC-8023 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Kenwood KDC-8023 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Kenwood KDC-8023 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Kenwood KDC-8023 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Kenwood KDC-8023. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Kenwood KDC-8023 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
