Benutzeranleitung / Produktwartung KDC-4016 des Produzenten Kenwood
Zur Seite of 25
KDC-4016 KDC-2016 ©B 64-1548-00 (MW) COMPACT DIGITAL AUDIO CD-RECEIVER INSTRUCTION MANUAL KDC-4016/2016(M)Cover 02.5.15 10:12 AM Page 1.
— 2 — English Contents Before use Safety precautions ........................................................................3 Handling Compact discs................................................................5 General features Power .........
— 3 — To prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery, or ground wires, make sure to use automotive- grade wires or other wires with a 0.
— 4 — English • If you experience problems during installation, consult your Kenwood dealer. • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer.
— 5 — Handling Compact discs Playing a CD that is dirty, scratched or warped can cause the sound to skip and the unit to operate incorrectly, resulting in worsened sound quality. Take the following precautions to prevent your CDs from getting scratched or damaged.
Switching Modes: Each time you press the SRC (source) button, the mode switches as follows: Selecting standby mode: Press the SRC button repeatedly and switch to "OFF" When "OFF" is displayed, the standby mode is activated. The standby mode turns all functions off while leaving the power to the unit on.
"BAS": Adjust the bass level. Setting values: - 8 - + 8 Adjust various parameters of sound quality. Press the A.ADJ button for at least one second to enter the control mode. Selecting mode Press either the FM or AM button. Each time the button is pressed, the adjustment mode will change.
The faceplate of the unit can be detached and taken with you, helping to deter theft. Grooves Release button Projections Theft Deterrent Faceplate Adjust the time. When the time is not displayed, first press the CLK button to display the time. Press the CLK button for at least two seconds to enter the clock adjustment mode.
T uner features Removing the Faceplate: Press the release button. The faceplate is unlocked, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached.
Switch the frequency step used in seeks. The factory defaults are 50 kHz for FM and 9 kHz for AM. Turn the power off. Hold down buttons #1 and #5, then turn the power back on. The frequency step settings will be changed to 200 kHz for FM and 10 kHz for AM.
CD/External disc control features Temporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. The factory default for this function is ON. Turning CRSC On/Off: Press the CRSC button for at least one second to turn the function on/off.
Search forward or backward through the tracks on the disc until you reach the one that you want to listen to. Making a Reverse Track Search: Track Search Fast Forwarding Disc Play: Hold down on the ¢ button. Release your finger to play the disc at that point.
Successively play the beginning of each track on a disc until you find the track that you want to listen to. Starting the Track Scan : Press the SCAN button. The SCN indicator lights up and the first 10 seconds of each track will be played, in order. The track number currently being heard blinks in the display.
Function of the KDC-4016 Play the tracks on all the discs in the disc changer in random order. Press the M.RDM button to switch magazine random play on and off. The RDM indicator lights up when magazine random play is turned on. The disc and track numbers will change over and over in the display as the next track is being selected.
The supplied remote control unit is in its storage case. Do not set the remote on hot places such as above the dashboard. Loading and Replacing the Batteries: Use two “AAA”-size batteries. Slide the cover while pressing downwards to remove it as illustrated.
• 4 / ¢ buttons Press the 4 button to search through the tracks backward. Press the ¢ button to search through the tracks forward. • DISC buttons (for disc changers) Press the DISC – button to search through the discs backward. Press the DISC + button to search through the discs forward.
— 17 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 2 CAUTION Accessories ..........................................1 ........
English — 18 — Connecting Wires to Terminals P.CONT.OUT ANT. CONT. + + + + FRONT • L FRONT • R REAR • L REAR • R – – – – – + When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear).
— 19 — Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). NOTE Accessory 2 Metal mounting strap Self-tapping screw (commerciall y available) Firewall or metal support Accessory 4 Installation ■ Installation 8 mm MAX.
English — 20 — Installation Removing the hard rubber frame ■ When the lower level is removed, remove the upper two locations. 2 The frame can be removed from the top side in the same manner. NOTE Catch Lock Engage the catch pins on the removal tool and remove the two locks on the lower level.
— 21 — Accessory 7 Screwing the Faceplate on the Unit ■ Never insert the taptite screw (ø4 × 16 mm) in any other screw hole than the one specified. If you screw it in another hole, it will contact and may cause damage to the mechanical parts inside the unit.
English — 22 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. Troubleshooting Guide SOLUTION POSSIBLE CAUSE PROBLEM One of the speaker wires is being pinched by a screw in the car.
— 23 — External disc control mode (KDC-4016 only) The computer chip in the unit is not functioning normally. Press the reset button on the unit (see p. 4). The disc control mode cannot be selected. No wire has been connected to the disc changer input terminal on the unit.
English — 24 — Troubleshooting Guide The following messages are displayed when certain problems are occurring in your system. Take the recommended actions. Nothing has been recorded on the MD. ] The next MD will automatically be played. E-10 No disc magazine has been loaded in the changer.
— 25 — FM tuner section Frequency range (200 kHz space) .............87.9 MHz – 107.9 MHz (50 kHz space) ..............87.5 MHz – 108.0 MHz Usable sensitivity (S/N = 30dB) .....................9.3dBf (0.8 µV/75 Ω ) Quieting Sensitivity (S/N = 50dB) .
Ein wichtiger Punkt beim Kauf des Geräts Kenwood KDC-4016 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Kenwood KDC-4016 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Kenwood KDC-4016 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Kenwood KDC-4016 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Kenwood KDC-4016 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Kenwood KDC-4016 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Kenwood KDC-4016 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Kenwood KDC-4016. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Kenwood KDC-4016 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
