Benutzeranleitung / Produktwartung KDC-2020 des Produzenten Kenwood
Zur Seite of 22
KDC-4020 KDC-3020 KDC-2020 KDC-1020 KDC-1020S © B64-2115-00 (MWN/IW) INSTRUCTION MANUAL CD-RECEIVER KDC-4020(M)Cover 01.11.29 10:32 AM Page 1.
— 2 — English Contents Safety precautions ......................3 About CDs ...................................5 General features .................
— 3 — Safety precautions To prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery , or ground wires, make sure to use automotive- grade wires or other wires with a 0.
— 4 — English • If you experience problems during installation, consult your Kenwood dealer . • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer .
— 5 — About CDs Handling CDs • Don’t touch the recording surface of the CD. • CD-R and CD-RW are easier to damage than a normal music CD. Use a CD-R or a CD-RW after reading the caution items on the package etc. • Don’t stick tape etc. on the CD.
Tu rning the volume down quickly . Press the [A TT] button. Each time the button is pressed the Attenuator turns ON or OFF . When it’ s ON, the "A TT" indicator blinks. Attenuator Increasing V olume Press the [ u ] button. Decreasing V olume Press the [ d ] button.
1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below .
Function of the KDC-4020/KDC-3020/KDC-2020 The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate Press the Release button.
T uner features • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached. • Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity .
T emporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. CRSC (Clean Reception System Circuit) Calling up the stations in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Call up the station Press the [#1] — [#6] button.
CD/External disc control features Changing the tuning frequency step. The original setting is FM band 50 kHz, and AM band 9 kHz. 1 Tu rn the power OFF Press the [SRC] button for at least 1 second. 2 Switch the frequency step While pressing the [#1] and [#5] button, press the [SRC] button.
Replaying the song/disc you're listening to. Press the [REP] button. Each time the button is pressed the Repeat Play switches as shown below . Repeat play Display T rack Repeat "REP" indicator & T rack No. blink. Album Repeat "REP" indicator & Disc No.
Function of the KDC-4020/KDC-3020/KDC-2020 Play the songs on all the discs in the disc changer in random order . Press the [M.RDM] button. Each time the button is pressed the Magazine Random Play turns ON or OFF . When it's ON, the "RDM" indicator is ON and the track and disc number blink.
[ 4 ]/ [ ¢ ] buttons Doing track forward and backward. [DISC+]/ [DISC-] buttons Doing album forward and backward. [ 38 ] button Each time the button is pressed the song pauses and plays. In Disc source [FM]/ [AM] buttons Select the band. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands.
— 15 — — 15 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. 1. T o prevent a short circuit, remove the key from the ignition and disconnect the - battery .
English — 16 — — 16 — P.CONT ANT. CONT. FRONT • L FRONT • R REAR • L REAR • R – + REAR L R FM/AM antenna input 1 Rear left output (White) 23 Rear right output (Red) 28 Fuse (10A) 24 .
— 17 — — 17 — Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Metal mounting strap (commercially available) Self-tapping screw (commercially available) Firewall or metal support Screw (M4X8) (commercially available) ■ Installation 8 mm MAX.
English — 18 — — 18 — ■ Removing the hard rubber frame 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner . Catch Lock 1 Engage the catch pins on the removal tool and remove the two locks on the lower level.
— 19 — T roubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON.
English — 20 — Tr oubleshooting Guide Disc source ? "A Vin" is displayed without achieving External disc control mode. 50 ✔ O-N switch is set to "O" side. ☞ Set the switch to "N" side. ✔ Unsupported disc changer is connected.
— 21 — The messages shown below display your systems condition. E-01: No disc magazine has been loaded in the changer . The disc magazine is not completely loaded. E01 ➪ Load the disc magazine properly . No CD in the unit. ➪ Insert the CD. E-02: No disc has been loaded in the disc magazine.
English — 22 — Specifications FM tuner section Frequency range (200 kHz space) ............87.9 MHz – 107.9 MHz Frequency range (50 kHz space) ..............87.5 MHz – 108.0 MHz Usable sensitivity (S/N = 30dB) .................... 9.3dBf (0.8 µV/75 Ω ) Quieting Sensitivity (S/N = 50dB) .
Ein wichtiger Punkt beim Kauf des Geräts Kenwood KDC-2020 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Kenwood KDC-2020 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Kenwood KDC-2020 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Kenwood KDC-2020 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Kenwood KDC-2020 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Kenwood KDC-2020 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Kenwood KDC-2020 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Kenwood KDC-2020. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Kenwood KDC-2020 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
