Benutzeranleitung / Produktwartung 415.161108 des Produzenten Kenmore
Zur Seite of 28
Use and Care Guide LiquidPropane Gas Grill Kenmore Model No. 415.16110800 This Grill is For Outdoor Use Only ® • Read this manual before cooking on grill. Failure to follow all manufacturer's instructions could result in fire or e×plosion which could cause property damage, personal injury or death.
if you smell gas: 1. Shut off gas to the appliance. 2. Extinguish any open flame. 3. Open lid. 4. if odor continues, keep away from the appliance and immediately call your gas supplier or your fire department. 1. Do not store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.
For Your Safety ...................................... 2 Grill Service Center ................................... 2 Product Record Information ............................ 2 Safety Symbols ...................................... 2 Installation Safety Precautions .
• NEVER store a spare LP tank under or near grill or in enclosed areas • Never fill the cylinder beyond 80% full. • An overfilled or improperly stored tank is a hazard due to possible gas release from the safety relief valve. • if you see, smell or hear escaping gas, immediately get away from the LP tank/grill and call your fire department.
LP Tank Exchange o Many retailers that sell grills offer you the option of replacing your empty LP tank through an exchange service. Use only those reputable exchange companies that inspect, precision fill, test and certify their cylinders.
Hold coupling nut and regulator as shown for proper connection to LP tank valve. Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. , 3. Be sure regulator is tightly connected to LP tank. Completely open LP tank valve by turning OPD hand wheel counterclockwise.
For Safe Use Of Your Grill And To Avoid Serious injury: • Do not let children operate or play near grill. • Keep grill area clear and free from materials that burn. • Do not block holes in bottom or back of grill. • Check burner flames regularly.
Main burner Ignitor Lighting A Do not lean over grill while lighting. 1. Open lid during lighting. 2. Turn ON valve from source or tank. 3. Push and turn Ignition Burner control knob to _- HI and immediately press and hold Electronic Ignition button. 4.
Turning Grill Off . Turn all knobs to OFF position. Turn LP tank off by turning OPD hand wheel clockwise to a full stop. Ignitor Check • Turn gas off at LP tank. Press and hold ignitor button. "Click" should be heard and spark seen each time between collector box or burner and electrodes.
Cleaning the Burner Assembly Follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting grill. 1. Turn gas off at control knobs and LP cylinder, 2. Remove cooking grate and vaporiser bar. 3. Under grill remove grease cup, disconnect ignitor wire and clips from burner.
1 2 2 1 3 1 4 1 5 1 6 1 7 2 8 1 9 2 10 4 11 5 12 12 13 46 14 1 15 1 16 1 17 16 18 2 19 2 20 1 21 1 22 1 23 1 24 1 25 1 26 1 27 32 28 1 29 1 3O 1 31 1 32 1 33 3 34 22 35 1 36 1 37 2 38 2 39 4 4O 4 41 4 42 1 43 1 Description ......................... Part # Upper Leg .
12 °464810408 ,# (_/-o G ® _b ® .
Left Leg Place one upperleg as shown. NOTE: Left front and left back legs do not have leg extenders. In front, attach upperleg, side brace and left front leg (curve) with #10-24x1-1/4" screw and #10-24flange nut. In back, attach upperleg, side brace and left back leg (straight) with #10-24x1-1/4" screw and #10-24flange nut.
Tank Exclusion Wire Hooktank exclusion wire into legs with opening for LPcylinderon side brace side. Side Brace Larger openingside TankExclusionWire D Upperand Lower Panels Lay front legs down on the floor. Fit upperpanelwith two tabs between legs.Attach with #10-24x2" screws and #10-24 flange nuts.
Back Braces to Cart Remove previously attached screwsand nutsfrom upper legs as shown. Attach back braces with #10-24x1-1/4" screws and #10-24flange nuts. Back Brace / 12 #10-24xl -1/4" Remove screws and Screw nuts to attach back brace Qty. 6 13 #10-24Flange Nut Qty.
17 Control Panel and Upper Firebox Supports Stand cart upright. In front, fit control panel betweenleft and right legs. Insert #10-24x2" screws to hold panelin place.
Heat Shield Attach heat shield with #10-24x1/2" screws and#10-24flange nuts. HeatShield 27 27 #10-24Xl/2" Screw Qty. 2 13 #10-24Flange Nut Qty. 2 Tank Retainer Insert tank retainer into side brace and securewith wing screw. 30 Wing Screw Qty.
Burner, Firebox and Control Knobs Place burner assembly into firebox (A). Fasten the burnerassembly to the firebox using 5ram fiber washers and #10-24x 1/2" machine screws. Place fireboxonto upper fireboxsupports with burner tubes below heat shield.
Shelves Insert mounting brackets into side shelfsupports with #10-24x1/2"screws (A). Attach backof leg with 1/4"-20x1-1/4"screws and!/4"-20 flange nuts, Do not fully tighten. Attach mounting bracketsto front of leg with 1/4"-20x1/2"screws (B).
Sideburner Attach sideburner valvewith #8-32x3/8" machine screws (A). Attach sidebumerpanwith #8x3/8" self-tap screws and 5mm ID 9mm OD fiber washers. Place sideburner into shelf(B). Makesure valve is inside sidebumer tube.Attach sideburner with wing nut and 5mm ID 9mm OD fiber washer.
27 Lower Firebox Hinges Attach lower hinges to backof firebox using #10-24x1/2"screws, 5ram fiber washers and #10-24 flange nuts. The centerflat portion of the hingeshould be at the bottom (see inset). #10-24x1/2" Screws Qty. 4 34 5mm Fiber Washers 13 Qty.
Lid Place lid assembly onto firebox, aligning hinges. Hinges on lid fit inside hinges on firebox. Secure using two hinge pins and hitch pins (See inset ). 11 Hitch Pins Qty. 2 10 Hinge Pins Qty. 2 Heat Diffuser Place heat diffuser over screws in firebox.
Cooking Grate Place grate into firebox. Cooking Grate Swing Away } Insert ends of Swing Away pivotwire into holes in sidesof grill lid. Insert ends of Swing Away legwire into holes in sidesof firebox. NOTE: Pivotand legwires, runningside-to-side, should be under wires running front-to-back.
Grease Cup Clip and Grease Cup Hang grease cup clip from bottom of fireboxand place grease cup into grease cup clip. CAUTION FaUure to install grease cup clip and cup will cause hot grease to drip from bottom of grill with risk of fire or property damage, Grease Cup Clip Grease Cu LP Tank LP tank is sold separately.
Troubleshooting EMERGENCIES: if a gas leak cannot be stopped, or a fire occurs due to gas leakage, call the fire department. , Damaged hose. , Turn off gas at LP tank. If hose is cut or cracked,replace Gas leaking from cracked/cut/burned valve/hose/regulator.
Burner(s) will not light using ignitor. Troubleshooting (continued} , Push-button sticks at bottom.. Burner(s) will not match light. Suddendrop in gas flow or low flame. Flames blow out. Flare-up. Persistent grease fire. Flashback... (fire in burner tube(s)).
Troubleshooting - Electronic ignition , Battery not installed properly. SECTION I No sparks appearat any electrodes when ignition buttonis pushed; no noise can be heardfrom spark module. SECTION II No sparks appearat any electrodes when ignition switchis pushed; noise can be heardfrom spark module.
Your Home ':;i_i_i_i_i_i_i_i_i_i_i_i_i_i iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii Forrepair-in yourhome-ofall majorbrand appliances, iiiiiiiiiiiiii iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii lawn and garde.
Ein wichtiger Punkt beim Kauf des Geräts Kenmore 415.161108 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Kenmore 415.161108 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Kenmore 415.161108 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Kenmore 415.161108 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Kenmore 415.161108 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Kenmore 415.161108 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Kenmore 415.161108 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Kenmore 415.161108. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Kenmore 415.161108 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
