Benutzeranleitung / Produktwartung TK-C215V4U des Produzenten JVC
Zur Seite of 24
DOME CAMERA TK-C215V4 INSTR UCTIONS (A) For Customer Use: Enter below the Se rial No. which is located on the body . Retain this inf ormation for future referen ce.
2 Intr oduction Safety Precautions CAUTION:TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
3 I 䢇 The unit is to be powered by a DC 12 V or an AC 24 V po wer supply . 䢇 The unit is to be powered by a UL Listed DC 12 V or an AC 24 V po wer supply .
4 Intr oduction These are general IMPORT ANT SAFEGU ARDS and certain items may not apply to all appliances. 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions should be adhered to.
5 Thank you f or purchasing this product. (These instructions are for: TK -C215V4U.) Before beginning to oper ate this unit, please read the instruction manual carefully in order to make sure that the best possible perf or mance is obtained.
6 Intr oduction Intr oduction Safety P recautions ......................................... 2 Characteristics ............................................... 5 Contents ......................................................... 6 Operating Precautions .
7 䢇 T o sav e energy , when it is not being used turn the system’ s power off. 䢇 This camera has been designed f or indoor use. It cannot be used outdoors. 䢇 Do not install or use the camera in the follo wing places. ● In a place exposed to rain or moisture .
8 Intr oduction Camera A Mounting hole (elliptica l) x 4 Use these when mounting the camera to the NO TE: electrical box. ( A pg. 18) When installing the camera onto the electric box, install it using the supplied adaptor ring. B Mounting h ole (rou nd) x 4 Use these when mounting the camera to the ceiling or wall.
9 Camera (Interior) The dome cov er , inner dome and outer case are removed. Procedures for remo val. ( A pg. 14 A Embedding the camera to the ceiling B , Step 3. to Step 5. ) J Strap A plate to connect the camera unit and the dome cov er . K Fastening Screw (x 3) When embedding the camera in the ceiling, turn this screw to secure the camera.
10 Intr oduction Set the video setting switches on the camer a unit before mounting it. T o set the switches , use a fine-tipped scre wdriver . A [RESET/SPO T] RESET/SPO T button When this button is pressed, the v alue of the white balance or phase adjusted manually is reset to the default v alue.
11 4. [WHT .BAL.] A TW/MANU AL selection swit ch. For selecting whether to adjust the white balance automatically or manually . When the setting is changed from manual to A TW, the setting values in the manual mode will be reset. The camera s witches to the same mode as with pressing the [RESET] button.
12 Installati on and connection The maximum connection distance varies with the type of cable used. Please refer carefully to the table f or each cable during conn ection. * Be sure to turn off th e power of de vices before connecting cables. Video signal cables Connect the coaxial cables (BNC) to the video signal output connector (BNC).
13 NO TE: ● T ur n OFF the power supply to all equipment to be used before making connections . ● Read the Instruct ion Manual f or each piece of equipment to be used before making connections. Getting Started CA UTION: ● When mounting the camera to the ceiling, ensure to wear saf ety glasses to protect the ey e from any f alling object.
14 Installati on and connection Embedding the camer a to the ceilin g * Make use of a ceiling material with a thickness between 9.5 mm to 22 mm. 䡵 Setup 1. Open a hole in the ceiling. ( R 120 mm , 4 3/4 inches) 2. Draw the fall pre vention wire mounted to the ceiling slab and the cable ou t from the ceiling in adv ance .
15 䡵 Connecting 1. Attach the fall prevention wire to th e camera, followed b y attaching it to the ceiling slab (Fall prevention wire is not included.) 2. Connect the video signal cab le . ( A pg. 12) Lower the co ver and connect the connectors . Upon connecting, cover the connectors using the protection cover .
16 Installati on and connection When mounting the camera directly to the ceiling or on th e wall When mounting to a wall, replace areas in dicated as “ceiling” in the procedures by “wall”. 䡵 Setup 1. Open a hole in the ceiling. ( R 30 mm , 1 1/8 inches) Make us e of the template sup plied to open a ho le.
17 4. Connect the video signal cab le . ( A pg. 12) Lower the protection co ver and connect the connectors. Upon connecting, restore the protection cov er to cover the connectors . 5. Connect the input po wer supply cab le . ( A pg. 12) 6. Wrap insulation ta pe around cables.
18 Installati on and connection When mounting t h e camera to the electrical box NO TE: Before mounting the camer a to electrical boxes , please ref er to local building codes for bo x type to use for lo w-voltage wiring. 䡵 Connecting 1. Align j with the shootin g direction when mounting the cover to the electrical box.
19 Adjusting Im age Upon mounting the camera, adjust the images while checking the actual image. Mounting the test monitor Connect the [MONITOR] terminal of this camera to a test monitor to adjust the camera’s shooting direction, image and fo cus. * The power to the camera body must be ON when adjustments are performed.
20 Adjusting Im age Adjusting the field angle/focus/ brightness Upon deter mining the imaging direction, adjust the field angle, f ocus and iris lev el accordingly .
21 After setting is complete, mount the Inner dome. 1. Mount the inner dome . Mount the inner dome to th e claws (3 locations). CA UTION: ● Mount the inner dome such that it doe s not cov er the lens. ● When mounting the inner dom e, be careful not to mov e the lens position.
22 Other s 䡵 Camera Signal system : Based on NTSC standard Scanning frequencies : 15.73 4 kHz (Horizontal), 59.94 Hz (V er tical) Image device: 1/4" IT CCD Effective picture elements: : 380,0 0.
23 Focus chart TK-C215V4_EN.book Page 23 Wednesday, J une 14, 2006 8:00 PM.
© 2006 Victor Company of Japan, Limited LST0420-001A TK-C215V4 DOME CAMERA TK-C215V4_EN.book Page 24 Wednesday, J une 14, 2006 8:00 PM.
Ein wichtiger Punkt beim Kauf des Geräts JVC TK-C215V4U (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie JVC TK-C215V4U noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für JVC TK-C215V4U - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von JVC TK-C215V4U reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über JVC TK-C215V4U erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon JVC TK-C215V4U besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von JVC TK-C215V4U verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit JVC TK-C215V4U. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei JVC TK-C215V4U gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
